Germanas Peleckis

Thermoelectric properties of Ca₃Co₄O₉ and Ca_2.8Bi_0.2Co₄O₉ thin films in their island formation mode

Publisher: Springer Science and Business Media LLC

Date: 17-06-2013

DOI: 10.1557/JMR.2013.163

Epitaxial growth mechanism of silicene on Ag(111)

Publisher: IEEE

Date: 02-2014

DOI: 10.1109/ICONN.2014.6965253

Magnetic and transport properties of transition metal ion doped diluted magnetic semiconductors In2-xTMxO3 (TM = Cr, Mn, Fe, V)

Publisher: IEEE

Date: 05-2006

DOI: 10.1109/INTMAG.2006.375645

Enhanced thermoelectric properties of NaxCoO2 whisker crystals

Publisher: AIP Publishing

Date: 29-12-2003

DOI: 10.1063/1.1634371

A Liquid-Metal-Based Magnetoactive Slurry for Stimuli-Responsive Mechanically Adaptive Electrodes

Publisher: Wiley

Date: 17-07-2018

DOI: 10.1002/ADMA.201802595

Abstract: Electrical communication between a biological system and outside equipment allows one to monitor and influence the state of the tissue and nervous networks. As the bridge, bioelectrodes should possess both electrical conductivity and adaptive mechanical properties matching the target soft biosystem, but this is still a big challenge. A family of liquid-metal-based magnetoactive slurries (LMMSs) formed by dispersing magnetic iron particles in a Ga-based liquid metal (LM) matrix is reported here. The mechanical properties, viscosity, and stiffness of such materials rapidly respond to the stimulus of an applied magnetic field. By varying the intensity of the magnetic field, regulation within a factor of 1000 of the Young's modulus from ≈kPa to ≈MPa, and the ability to reach GPa with more dense iron particles inside the LMMS are demonstrated. With the advantage of high conductivity of the LM matrix, the functions of the LMMS are not only limited to the soft implanted electrodes or penetrating electrodes in biosystems: the electrical response based on the LMMS electrodes can also be precisely tuned by simply regulating the applied magnetic field.

Comparative studies of IR spectra of deprotonated serine with classical and thermostated ring polymer molecular dynamics simulations

Publisher: AIP Publishing

Date: 09-2021

DOI: 10.1063/4.0000124

Abstract: Here we report the vibrational spectra of deprotonated serine calculated from the classical molecular dynamics (MD) simulations and thermostated ring-polymer molecular dynamics (TRPMD) simulation with third-order density-functional tight-binding. In our earlier study [Inakollu and Yu, “A systematic benchmarking of computational vibrational spectroscopy with DFTB3: Normal mode analysis and fast Fourier transform dipole autocorrelation function,” J. Comput. Chem. 39, 2067 (2018)] of deprotonated serine, we observed a significant difference in the vibrational spectra with the classical MD simulations compared to the infrared multiple photon dissociation spectra. It was postulated that this is due to neglecting the nuclear quantum effects (NQEs). In this work, NQEs are considered in spectral calculation using the TRPMD simulations. With the help of potential of mean force calculations, the conformational space of deprotonated serine is analyzed and used to understand the difference in the spectra of classical MD and TRPMD simulations at 298.15 and 100 K. The high-frequency vibrational bands in the spectra are characterized using Fourier transform localized vibrational mode (FT-νNAC) and interatomic distance histograms. At room temperature, the quantum effects are less significant, and the free energy profiles in the classical MD and the TRPMD simulations are very similar. However, the hydrogen bond between the hydroxyl–carboxyl bond is slightly stronger in TRPMD simulations. At 100 K, the quantum effects are more prominent, especially in the 2600–3600 cm−1, and the free energy profile slightly differs between the classical MD and TRPMD simulations. Using the FT-νNAC and the interatomic distance histograms, the high-frequency vibrational bands are discussed in detail.

Al-Doped Zinc Oxide Nanocomposites with Enhanced Thermoelectric Properties

Publisher: American Chemical Society (ACS)

Date: 26-09-2011

DOI: 10.1021/NL202439H

Abstract: ZnO is a promising high figure-of-merit (ZT) thermoelectric material for power harvesting from heat due to its high melting point, high electrical conductivity σ, and Seebeck coefficient α, but its practical use is limited by a high lattice thermal conductivity κ(L). Here, we report Al-containing ZnO nanocomposites with up to a factor of 20 lower κ(L) than non-nanostructured ZnO, while retaining bulklike α and σ. We show that enhanced phonon scattering promoted by Al-induced grain refinement and ZnAl(2)O(4) nanoprecipitates presages ultralow κ ∼ 2 Wm( -1) K(-1) at 1000 K. The high α∼ -300 μV K(-1) and high σ ∼ 1-10(4) Ω(-1 )m(-1) result from an offsetting of the nanostructuring-induced mobility decrease by high, and nondegenerate, carrier concentrations obtained via excitation from shallow Al donor states. The resultant ZT ∼ 0.44 at 1000 K is 50% higher than that for the best non-nanostructured counterpart material at the same temperature and holds promise for engineering advanced oxide-based high-ZT thermoelectrics for applications.

Effect of gallium doping and ball milling process on the thermoelectric performance of n-type ZnO

Publisher: Springer Science and Business Media LLC

Date: 24-07-2012

DOI: 10.1557/JMR.2012.220

Co valence by K-edge X-ray absorption spectroscopy, magnetic properties, and structure of polycrystalline bulk Zn/sub 1-x/Co/sub x/O

Publisher: Institute of Electrical and Electronics Engineers (IEEE)

Date: 10-2005

DOI: 10.1109/TMAG.2005.854689

Synthesis of functional oxides by a novel mechanical milling-electric discharge method

Publisher: Royal Society of Chemistry (RSC)

Date: 2006

DOI: 10.1039/B608437K

Microscopic unravelling of nano-carbon doping in MgB2 superconductors fabricated by diffusion method

Publisher: Elsevier BV

Date: 09-2015

DOI: 10.1016/J.JALLCOM.2015.05.082

Ferromagnetism in Mn-doped In2O3 oxide

Publisher: Elsevier BV

Date: 06-2006

DOI: 10.1016/J.JMMM.2005.07.004

Colossal Electroresistance and Giant Magnetoresistance in Doped PbPdO₂Thin Films

Publisher: Wiley

Date: 05-06-2009

DOI: 10.1002/ADMA.200802868

Phase formation and magnetotransport of alkali metal doped Na0.75CoO2 thermoelectric oxide

Publisher: AIP Publishing

Date: 21-04-2010

DOI: 10.1063/1.3365491

Abstract: Synthesis and characterization of bulk NaxCoO2 s les substituted by K and Rb is reported. Phase formation studies revealed a narrow stable region for Na-alkali metal-Co system. Whisker and platelike single crystalline structures have been found to form on the surface of the pellets in case of K doping. All s les were metallic and no characteristic anomaly in R-T curves was observed for Rb doped s le. Magnetoresistance measured has a pronounced positive response only for K-doped and pure NaxCoO2 phases, reaching 11% and 7% at 5 K temperature, respectively.

Band structures, and magnetic and transport properties of La doped two dimensional Sr2CoO4

Publisher: AIP Publishing

Date: 05-2007

DOI: 10.1063/1.2714196

Abstract: In this work, we report on our studies on the band structure calculations, structures, transport, and magnetic properties in two dimensional layer structured perovskite compounds Sr2−xLaxCoO4. Structure refinement results reveal that these compounds crystallized in K2NiF4-type structures with space group I4∕mmm. The temperature dependence of resistivity shows a semiconductorlike behavior over a wide range of temperatures, a metal-insulator transition at 240K, and an upturn at 160K for the x=1, 1.25, and 0.75 s les. A coercive field is about 1T for the s le with x=0.75, while it is about 0.05T for x=0.75 and 0.1T for the x=1.25 s les. A negative field hysteresis magnetoresistance in close correlation with the coercive field has been observed and can be explained by the grain boundary tunneling effect. The first-principles band structure calculations were carried out for Sr1.5La0.5CoO4 and the results indicate that the system is metallic with a high spin polarization which is responsible for the observed large magnetoresistance.

Synthesis and structural characterization of a TCNQ based organic semi-conducting material with a 2:5 stoichiometry

Publisher: American Chemical Society (ACS)

Date: 22-11-2011

DOI: 10.1021/JO2018334

Abstract: The tetrabutylammonium complex with a 2:5 stoichiometry, (n-Bu(4)N)(2)(TCNQ)(5), has been prepared and structurally characterized by X-ray crystallography. Diagnostic bands in the Raman spectrum and signature features in the electrochemistry confirm that the TCNQ moieties are partially charged in the solid state. EPR, magnetic susceptibility, and electrical conductivity measurements are all consistent with (n-Bu(4)N)(2)(TCNQ)(5) behaving as a quasi-one-dimensional organic semiconductor.

Large positive magnetoresistance effect below Curie temperature in In1.90−xMn0.1SnxO3

Publisher: AIP Publishing

Date: 05-2007

DOI: 10.1063/1.2714192

Abstract: We report on the magnetoresistance (MR) and magnetic properties of In1.90−xMn0.1SnxO3 (0⩽x⩽0.06) oxide. All s les were found to be ferromagnetic below TC=46K. Sn doping changed In1.90Mn0.1O3 from an insulator to a highly conducting phase at 300K. A positive MR effect was observed over a wide temperature range just below TC. Calculated MR values reached a maximum of 20% at 5K. A change in the MR effect, from positive to negative, occurred under magnetic field H& T at 5K. The results of x-ray absorption near-edge spectroscopy indicated that Mn ions are present both as Mn2+ and Mn4+.

Magnetotransport and magnetic properties of weak ferromagnetic semiconductors: Ca doped LaCrO3

Publisher: AIP Publishing

Date: 26-03-2008

DOI: 10.1063/1.2837624

Abstract: We report the magnetic and magnetotransport properties of Ca doped La1−xCaxCrO3 (x=0, 0.1, 0.2, and 0.3). Both the magnetic and transport properties are very sensitive to Ca substitution. The Néel temperature TN decreases substantially with increasing calcium doping concentration from 290to160K. A weak ferromagnetic state with large coercive fields of up to 3T is present for the Ca doped LaCrO3. The temperature dependence of the resistivity shows that all the Ca doped compounds are semiconducting and their resistivities decrease with increasing Ca for low doping levels. The resistivity curves show thermally activated behavior and a variable range hopping behavior at high temperatures. The magnetotransport measurements show a negative magnetoresistance. Furthermore, an anomalous peak was observed in the field dependence of magnetoresistance for the LCCO materials.

Giant positive magnetoresistance in Fe doped In2O3 and InREO3 (RE=Eu,Nd) composites

Publisher: AIP Publishing

Date: 06-02-2008

DOI: 10.1063/1.2830830

Abstract: Synthesis and characterization of Fe and rare earth (RE) (RE=Eu,Nd) codoped bulk In2O3 oxide are reported. Composites consisting of Fe-doped In2O3 and InREO3 phases were formed, as determined by x-ray diffraction and transmission electron microscopy, with particle sizes of 50–120nm. The composites exhibit superparamagnetic and semiconducting behavior. A giant positive magnetoresistance is observed at low temperatures, reaching 81% and 50% at 5K in Eu–Fe and Nd–Fe codoped s les, respectively.

Facile electrochemical synthesis of ultrathin iron oxyhydroxide nanosheets for the oxygen evolution reaction

Publisher: Royal Society of Chemistry (RSC)

Date: 2019

DOI: 10.1039/C9CC02941A

Abstract: Ultrathin iron oxyhydroxide nanosheets were synthesised by multiple potential cyclings on thermally annealed iron foils, acting as an efficient oxygen evolution electrocatalyst.

Sol–gel chemistry approach in the preparation of precursors for the substituted superconducting oxides

Publisher: Elsevier BV

Date: 12-2002

DOI: 10.1016/S0022-3093(02)01377-7

Room-temperature ferromagnetism in Mn and Fe codoped In2O3

Publisher: AIP Publishing

Date: 27-03-2006

DOI: 10.1063/1.2191093

Abstract: The synthesis and characterization of polycrystalline room-temperature ferromagnetic semiconductor (In0.9Fe0.1−xMnx)2O3 (x=0–0.1) oxide are reported. All of the s les with intermediate x values are ferromagnetic at room temperature. The highest saturation magnetization moment at 300K per total amount of magnetic ion is reached in the (In0.9Fe0.04Mn0.06)2O3 s le. The lattice constant a increases linearly with increasing Mn content. Fe-only doped s les were paramagnetic, while a Mn-only doped s le was found to be ferromagnetic below TC=46K.

Electronic structure and thermoelectric properties of Bi2Te3 crystals and graphene-doped Bi2Te3

Publisher: Elsevier BV

Date: 10-2010

DOI: 10.1016/J.TSF.2010.03.124

Isovalent substitution effects in the Na layer of γ-Na0.75CoO2 thermoelectric oxide

Publisher: Elsevier BV

Date: 09-2007

DOI: 10.1016/J.PHYSC.2007.03.062

Preparation and characterization of hybrid conducting polymer–carbon nanotube yarn

Publisher: Royal Society of Chemistry (RSC)

Date: 2012

DOI: 10.1039/C2NR11580H

Abstract: Hybrid polypyrrole (PPy)-multi walled carbon nanotube (MWNT) yarns were obtained by chemical and electrochemical polymerization of pyrrole on the surface and within the porous interior of twisted MWNT yarns. The material was characterized by scanning electron microscopy, electrochemical, mechanical and electrical measurements. It was found that the hybrid PPy-MWNT yarns possessed significantly higher mechanical strength (over 740 MPa) and Young's modulus (over 54 GPa) than the pristine MWNT yarn. The hybrid yarns also exhibited substantially higher electrical conductivity (over 235 S cm(-1)) and their specific capacitance was found to be in excess of 60 F g(-1). Measurements of temperature dependence of electrical conductivity revealed semiconducting behaviour, with a large increase of band gap near 100 K. The collected low temperature data are in good agreement with a three-dimensional variable range hopping model (3D-VRH). The improved durability of the yarns is important for electrical applications. The composite yarns can be produced in commercial quantities and used for applications where the electrical conductivity and good mechanical properties are of primary importance.

Superconductivity and critical current density in LaFeAsO1−xFx compounds

Publisher: Elsevier BV

Date: 10-2010

DOI: 10.1016/J.TSF.2010.03.129

Ice-Assisted Synthesis of Highly Crystallized Prussian Blue Analogues for All-Climate and Long-Calendar-Life Sodium Ion Batteries

Publisher: American Chemical Society (ACS)

Date: 28-01-2022

DOI: 10.1021/ACS.NANOLETT.1C04492

Abstract: For practical sodium-ion batteries, both high electrochemical performance and cost efficiency of the electrode materials are considered as two key parameters. Prussian blue analogues (PBAs) are broadly recognized as promising cathode materials due to their low cost, high theoretical capacity, and cycling stability, although they suffer from low-crystallinity-induced performance deterioration. Herein, a facile "ice-assisted" strategy is presented to prepare highly crystallized PBAs without any additives. By suppressing structure defects, the cathode exhibits a high capacity of 123 mAh g

Electrochemical Synthesis and Characterization of Semiconducting Ni(TCNQF4)2(H2O)2 (TCNQF4=2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane)

Publisher: Wiley

Date: 20-04-2012

DOI: 10.1002/EJIC.201101420

Polarisable force fields: what do they add in biomolecular simulations?

Publisher: Elsevier BV

Date: 04-2020

DOI: 10.1016/J.SBI.2019.12.012

Very strong intrinsic flux pinning and vortex avalanches in (Ba,K ) Fe2As2superconducting single crystals

Publisher: American Physical Society (APS)

Date: 28-07-2010

DOI: 10.1103/PHYSREVB.82.024525

Microstructure and magnetic properties in Sn1-xFexO2 (x = 0.01, 0.05, 0.10) nanoparticles synthesized by hydrothermal method

Publisher: Elsevier BV

Date: 02-2010

DOI: 10.1016/J.JALLCOM.2009.11.044

Spin wave scattering and interface magnetism in superconducting-ferromagnet-superconducting hybrid structures

Publisher: AIP Publishing

Date: 04-2009

DOI: 10.1063/1.3076544

Abstract: In this work we report on interlayer spin-polarized transport studies carried out on YBa2Cu3O7-δ/La2/3Sr1/3MnO3/YBa2Cu3O7-δ thin film multilayers. Anisotropic YBa2Cu3O7-δ high-temperature superconductors (YBCO) and the manganite La2/3Sr1/3MnO3 (LSMO) are layered metallic systems where the c-axis interlayer current transport occurs via sequential tunneling of charge carriers. The temperature dependence of the resistance R(T) for different applied fields shows that these heterostructures are clearly influenced by both the insulator-to-metal transition of the LSMO layers at ∼320 K and the stripe fluctuations in the conductivity of the YBCO layers at the onset of electronic inhomogeneity at ∼210 K. Furthermore, the tunneling of spin-polarized charge carriers between the YBCO layers through LSMO showed sharp switching between the high and low resistance states, which we assume corresponds to antiparallel and parallel alignments of the magnetic (spin) moments of these hybrid structures. The investigation of these promising hybrid structures is aimed at understanding the science of the new spin-based devices, laying the foundation for a new generation of ultrafast, nonvolatile electronics.

Magnetic and Transport Properties of Transition Metal Doped Polycrystalline In$_2$O$_3$

Publisher: Institute of Electrical and Electronics Engineers (IEEE)

Date: 10-2006

DOI: 10.1109/TMAG.2006.878846

Enhancement of flux pinning in a MgB2 superconductor doped with tartaric acid

Publisher: IOP Publishing

Date: 14-12-2007

DOI: 10.1088/0953-2048/20/1/020

Absence of ferromagnetism and strong spin-orbital coupling in polycrystalline in and Co codoped Zn/sub 1-x/Co/sub 0.075/In /sub x/O oxide

Publisher: Institute of Electrical and Electronics Engineers (IEEE)

Date: 10-2005

DOI: 10.1109/TMAG.2005.854731

Transport properties of HTS/CMR/HTS multilayers for spin injection devices

Publisher: Elsevier BV

Date: 09-2007

DOI: 10.1016/J.PHYSC.2007.03.428

Very high critical field and superior Jc-field performance in NdFeAsO0.82F0.18 with Tc of 51 K

Publisher: Wiley

Date: 02-01-2009

DOI: 10.1002/ADMA.200801527

Silicene: A Promising Anode for Lithium-Ion Batteries

Publisher: Wiley

Date: 22-03-2017

DOI: 10.1002/ADMA.201606716

Abstract: Silicene, a single-layer-thick silicon nanosheet with a honeycomb structure, is successfully fabricated by the molecular-beam-epitaxy (MBE) deposition method on metallic substrates and by the solid-state reaction method. Here, recent progress on the features of silicene that make it a prospective anode for lithium-ion batteries (LIBs) are discussed, including its charge-carrier mobility, chemical stability, and metal-silicene interactions. The electrochemical performance of silicene is reviewed in terms of both theoretical predictions and experimental measurements, and finally, its challenges and outlook are considered.

The mechanical and the electrical properties of conducting polypyrrole fibers

Publisher: AIP Publishing

Date: 15-05-2010

DOI: 10.1063/1.3425793

Abstract: The mechanical and the electrical properties of polypyrrole (PPy) fibers and electrochemically deposited PPy films were studied. It was found that the PPy fibers showed a significantly higher strength than the PPy films due to better orientation of the molecular structure. The electrochemically prepared PPy films had a higher electrical conductivity than that of the fibers at high temperature. At low temperature, the PPy fibers showed the higher conductivity. The conductivity results were analyzed in the frame of the three-dimensional variable range hopping model. The results showed that at room temperature the average hopping distance for the fibers was about 4 Å while for the films it increases to about 5.7 Å. This corresponds to about 1 and 2 monomer units in length for the fiber and film s les, respectively.

Spin-Polarised Transport and Evidence for Novel Spin Valve Behaviour in YBCO/LSMO/YBCO Hybrid Structures

Publisher: IEEE

Date: 2006

DOI: 10.1109/ICONN.2006.340614

Tuning the band gap in silicene by oxidation

Publisher: American Chemical Society (ACS)

Date: 30-09-2014

DOI: 10.1021/NN504451T

Abstract: Silicene monolayers grown on Ag(111) surfaces demonstrate a band gap that is tunable by oxygen adatoms from semimetallic to semiconducting type. With the use of low-temperature scanning tunneling microscopy, we find that the adsorption configurations and amounts of oxygen adatoms on the silicene surface are critical for band gap engineering, which is dominated by different buckled structures in √13 × √13, 4 × 4, and 2√3 × 2√3 silicene layers. The Si-O-Si bonds are the most energy-favored species formed on √13 × √13, 4 × 4, and 2√3 × 2√3 structures under oxidation, which is verified by in situ Raman spectroscopy as well as first-principles calculations. The silicene monolayers retain their structures when fully covered by oxygen adatoms. Our work demonstrates the feasibility of tuning the band gap of silicene with oxygen adatoms, which, in turn, expands the base of available two-dimensional electronic materials for devices with properties that is hardly achieved with graphene oxide.

Boosting NIR-driven photocatalytic water splitting by constructing 2D/3D epitaxial heterostructures

Publisher: Royal Society of Chemistry (RSC)

Date: 2019

DOI: 10.1039/C9TA02780G

Abstract: YF 3 :Yb, Tm@BiOCl possesses epitaxial heterostructure, which can quantitatively activate multiple energy transfer channels including excited-state energy transfer and fluorescence reabsorption, and then promote the NIR-driven photocatalytic properties.

High temperature ferromagnetism in Ni-doped In2O3 and indium-tin oxide

Publisher: AIP Publishing

Date: 10-07-2006

DOI: 10.1063/1.2220529

Abstract: Observation of high temperature ferromagnetism in Ni-doped In2O3 and indium-tin-oxide (ITO) s les prepared by a solid state synthesis route is reported. Both Ni-doped compounds showed a clear ferromagnetism above 300K with the magnetic moments of 0.03–0.06μB∕Ni and 0.1μB∕Ni at 300 and 10K, respectively. Ni-doped In2O3 s les showed a typical semiconducting behavior with a room temperature resistivity of ρ∼2Ωcm, while Ni-doped ITO s les were metallic with ρ∼2×10−2Ωcm. Analysis of different conduction mechanisms suggested that variable range hopping model explains our ρ-T data for the Ni-doped In2O3 s le the best.

National Institute Of Pharmaceutical Education And Research Hyderabad

Location: India

View Organisation

D.E.Shaw & Co

Location: India

View Organisation

Rajiv Gandhi University Of Health Sciences

Location: India

View Organisation

Vilniaus Universitetas

Location: Lithuania

View Organisation

University Of Wollongong

Location: Australia

View Organisation

Tokyo Institute Of Technology

Location: Japan

View Organisation

A Complete Near Field Scanning Optical Microscope For Advanced Characterization Of Novel And Functional Materials

Start Date: 2011

End Date: 2011

Funder: Australian Research Council

Materials Science And Superconductivity In The New Fe-based High Temperature Superconductors

Start Date: 2010

End Date: 2014

Funder: Australian Research Council

Titanium Dioxide 101: Characterisation And Utilisation Of Well Defined Single Crystal TiO2/dye Surfaces For Solar Energy Conversion

Start Date: 2009

End Date: 2009

Funder: University of Wollongong

Development Of Novel High Efficiency Thermoelectric Oxides For High Temperature Power Generation

Start Date: 2008

End Date: 2010

Funder: Australian Research Council

Development Of Nano-structured Thermoelectric Materials For Power Generation From Heat

Start Date: 2008

End Date: 2010

Funder: Australian Research Council

Nanostructure Engineered Iron-based Superconductors

Start Date: 2012

End Date: 2014

Funder: Australian Research Council

Synergetic Combination Of Localised Internal Magnesium Diffusion Process With Cold Compaction Technique For Fabrication Of Magnesium Diboride (MgB2) Superconductor Wires

Start Date: 2012

End Date: 2014

Funder: Australian Research Council

Combined Scanning Tunnelling Microscope System For Materials Characterization And Manipulation At Nano Scale

Start Date: 2010

End Date: 2010

Funder: Australian Research Council

Design And Exploration Of Novel P-block Materials For Solar Energy Conversion

Start Date: 2014

End Date: 2016

Funder: Australian Research Council

A Complete Thermo-electric Characterization Facility For Exploration Of Novel Materials And Devices At High Temperatures

Start Date: 2012

End Date: 2012

Funder: Australian Research Council

New Generation Cryogen-free Physical Property Measurement System

Start Date: 2015

End Date: 2015

Funder: Australian Research Council

Field Emission Gun Transmission Electron Microscope For The Research In Nanomaterials, Metal Alloys And Biological Sciences

Start Date: 2010

End Date: 2010

Funder: Australian Research Council

High Field Magnet For Materials Processing And Characterization

Start Date: 2008

End Date: 2008

Funder: Australian Research Council

Discovery Projects - Grant ID: DP140102581

Start Date: 2014

End Date: 06-2017

Amount: $520,000.00

Funder: Australian Research Council

Linkage Infrastructure, Equipment And Facilities - Grant ID: LE220100085

Start Date: 2022

End Date: 06-2023

Amount: $521,816.00

Funder: Australian Research Council

Discovery Projects - Grant ID: DP170101467

Start Date: 2017

End Date: 12-2020

Amount: $513,000.00

Funder: Australian Research Council

Linkage - International - Grant ID: LX0881969

Start Date: 2008

End Date: 12-2011

Amount: $58,600.00

Funder: Australian Research Council

Discovery Projects - Grant ID: DP1094073

Start Date: 07-2010

End Date: 06-2014

Amount: $555,000.00

Funder: Australian Research Council

Linkage Infrastructure, Equipment And Facilities - Grant ID: LE150100043

Start Date: 2015

End Date: 12-2015

Amount: $420,000.00

Funder: Australian Research Council

Discovery Projects - Grant ID: DP0879714

Start Date: 2008

End Date: 12-2011

Amount: $105,000.00

Funder: Australian Research Council

Discovery Projects - Grant ID: DP120100095

Start Date: 2012

End Date: 12-2015

Amount: $420,000.00

Funder: Australian Research Council

Linkage Infrastructure, Equipment And Facilities - Grant ID: LE110100099

Start Date: 2011

End Date: 12-2011

Amount: $290,000.00

Funder: Australian Research Council

Linkage Infrastructure, Equipment And Facilities - Grant ID: LE100100081

Start Date: 08-2010

End Date: 12-2010

Amount: $600,000.00

Funder: Australian Research Council

Linkage Projects - Grant ID: LP120100173

Start Date: 06-2012

End Date: 08-2016

Amount: $270,000.00

Funder: Australian Research Council

Linkage Infrastructure, Equipment And Facilities - Grant ID: LE0882347

Start Date: 2008

End Date: 12-2008

Amount: $340,000.00

Funder: Australian Research Council

Linkage Infrastructure, Equipment And Facilities - Grant ID: LE100100195

Start Date: 2010

End Date: 12-2011

Amount: $1,000,000.00

Funder: Australian Research Council

Linkage Infrastructure, Equipment And Facilities - Grant ID: LE120100069

Start Date: 01-2012

End Date: 12-2012

Amount: $200,000.00

Funder: Australian Research Council