ORCID Profile
0000-0002-3992-8602
Current Organisation
University of Portsmouth
Does something not look right? The information on this page has been harvested from data sources that may not be up to date. We continue to work with information providers to improve coverage and quality. To report an issue, use the Feedback Form.
Publisher: Elsevier BV
Date: 2022
Publisher: MDPI AG
Date: 09-04-2022
DOI: 10.3390/MA15082765
Abstract: In this study, mechanical testing of glass bead (GB), glass fiber (GF), and hybrid (GB/GF) composites was carried out. Following that, drilling tests were undertaken on glass bead/fiber-reinforced hybrid Polyamide 66 (PA66) polymer composites. The purpose of this study is to determine the mechanical properties of the cutting elements and the effect of cutting parameters (spindle speed and feed rate) and reinforcement ratios on thrust force and surface roughness (Ra). The contribution of the cutting parameters to the investigated outcomes was determined using statistical analysis. Optical microscopy and scanning electron microscopy (SEM) was used to inspect the hole quality and damage mechanisms. The results revealed that the feed rate was the most contributing factor to thrust force (96.94%) and surface roughness (63.59%). Furthermore, in comparison to other hybrid composites, the lowest Ra value was obtained as 0.95 µm in s les containing 30% GB, while the Ra value was 1.04 µm in s les containing 10% GF + 20% GB. Polymer PA reinforced with 30% GF had the highest strength, modulus of elasticity, impact strength, and hardness.
Publisher: MDPI AG
Date: 29-05-2021
DOI: 10.3390/MET11060891
Abstract: Millions of holes are produced in many industries where efficient drilling is considered the key factor in their success. High-quality holes are possible with the proper selection of drilling process parameters, appropriate tools, and machine setup. This paper deals with the effects of drilling parameters such as spindle speed and feed rate on the chips analysis and the hole quality like surface roughness, hole size, circularity, and burr formation. Al7075-T6 alloy, commonly used in the aerospace industry, was used for the drilling process, and the dry drilling experiments were performed using high-speed steel drill bits. Results have shown that surface roughness decreased with the increase in spindle speed and increased with the increase in the feed rate. The hole size increased with the high spindle speed, whereas the impact of spindle speed on circularity error was found insignificant. Furthermore, short and segmented chips were achieved at a high feed rate and low spindle speed. The percentage contribution of each input parameter on the output drilling parameters was evaluated using analysis of variance (ANOVA).
Publisher: MDPI AG
Date: 09-07-2023
Abstract: This paper deals with an experimental investigation of hole quality in Al2024-T3, which is one of the aerospace alloys used in aircraft fuselage skin due to its high level of resistance to fatigue crack propagation. The experiments are conducted with 6 mm uncoated carbide and HSS drill bits using a CNC machine under dry conditions and different drilling parameters. The characteristics of the hole quality are investigated in terms of its perpendicularity, cylindricity, circularity and hole size. An ANOVA (analysis of variance) and Pareto charts are used to analyze the effects of the drilling parameters on the hole quality. The hole quality is also assessed using a digital microscope to observe the formation of hole burrs. Moreover, scanning electron microscopy is also used to investigate the inside-hole surface defects. Further investigations are carried out using optical microscopy to inspect the post-drilling tool condition at high drilling parameters. The results show that hole quality reduces as the feed rate and spindle speed increase. However, from the ANOVA results and Pareto charts, the influence of the feed rate on the hole quality is found to be insignificant. At the same time, the type of drill bit material shows the highest percentage of contribution affecting the hole quality, following the spindle speed. The HSS drill bit shows more adhesion and built-up edges than the uncoated carbide drill bit. There were more burrs formed at the hole edges when the holes were drilled with uncoated HSS drill bits. In the same way, the SEM analysis reveals more surface deformation and damage defects inside the hole walls of holes drilled using the uncoated HSS drill bit.
Publisher: MDPI AG
Date: 17-08-2022
Abstract: In this study, a new machining approach (aqueous machining) is applied for mill machining and its performance is compared with traditional wet machining. AISI 1020 steel is employed as the test material and Taguchi statistical methodology is implemented to analyze and compare the performance of the two machining approaches. The cutting speed, feed rate, and depth of cut were the machining parameters used for both types of machining, while the selected response variables were surface roughness and hardness. Temperature variations were also recorded in aqueous machining. Compared with wet machining, aqueous machining resulted in lower surface roughness (up to 13%) for the same operating conditions and about 14% to 16% enhancement in hardness due to the formation of finer pearlite, as revealed by the microstructure analysis. Compared to the parent unmachined surface, the hardness of machined surfaces was 24% to 31% higher in wet machining and 44% to 51% higher in aqueous machining. Another benefit of aqueous machining was the energy gain, which ranged from 718 to 8615.96 J. This amount of heat energy can be used as waste heat for preheating domestic hot water, running the organic Rankine cycle with waste heat and preheating the inlet saline water for desalination, vacuum desalination, etc. If successfully implemented in the future, this idea will provide a step towards achieving sustainable machining by saving lubricants and toxic wastes in addition to saving energy for secondary applications.
Publisher: MDPI AG
Date: 02-12-2020
DOI: 10.3390/APP10238633
Abstract: Multi-spindle drilling simultaneously produces multiple holes to save time and increase productivity. The assessment of hole quality is important in any drilling process and is influenced by characteristics of the cutting tool, drilling parameters and machine capacity. This study investigates the drilling performance of uncoated carbide, and coated carbide (TiN and TiCN) drills when machining Al2024 aluminium alloy. Thrust force and characteristics of hole quality, such as the presence of burrs and surface roughness, were evaluated. The results show that the uncoated carbide drills performed better than the TiN and TiCN coated tools at low spindle speeds, while TiCN coated drills produced better hole quality at higher spindle speeds. The TiN coated drills gave the highest thrust force and poorest hole quality when compared with the uncoated carbide and TiCN coated carbide drills. Additionally, a multi-layer perceptron neural network model was developed, which could be useful for industries and manufacturing engineers for predicting the surface roughness in multi-hole simultaneous drilling processes.
Publisher: MDPI AG
Date: 20-08-2021
DOI: 10.3390/MA14164704
Abstract: Belt grinding of flat surfaces of typical parts made of steel and alloys, such as grooves, shoulders, ends, and long workpieces, is a good alternative to milling. Several factors can influence the belt grinding process of flat surfaces of metals, such as cutting speed and pressure. In this work, the importance of pressure in the belt grinding was investigated in terms of technological and experimental aspects. The grinding experiments were performed on structural alloy steel 30KhGSN2/30KhGSNA, structural carbon steel AISI 1045, corrosion-resistant and heat-resistant stainless steel AISI 321, and heat-resistant nickel alloy KHN77TYuR. The performance of the grinding belt was investigated in terms of surface roughness, material removal rate (MRR), grinding belt wear, performance index. Estimated indicators of the belt grinding process were developed: cutting ability reduced cutting ability for belt grinding of steels and heat-resistant alloy. It was found that with an increase in pressure p, the surface roughness of the processed surface Ra decreased while the tool wear VB and MRR increased. With a decrease in plasticity and difficulty of machinability, the roughness, material removal rate, reduced cutting capacity (Performance index) qper, material removal Q decreased, and the tool wear VB increased. The obtained research results can be used by technologists when creating belt grinding operations for steels and alloys to ensure the required performance is met.
Publisher: MDPI AG
Date: 12-02-2021
DOI: 10.3390/JMSE9020196
Abstract: Composite materials are used in various industries such as marine, aircraft, automotive, etc. In marine applications, composites are exposed to seawater, which can affect their mechanical properties due to moisture absorption. This work focuses on the durability of composite materials under the short-term effect of seawater ageing. The specimens were prepared from glass fiber/epoxy using a hand lap-up method and stitched in the z-direction with Kevlar fiber. The specimens were submerged in seawater for 24 and 35 days. A significant decrease in maximum load was found as specimen immersion time in seawater increased. The seawater ageing also affected fracture toughness with a reduction of 30% for 24 days immersion and 55% for 35 days. The ageing also caused the swelling of composites due to moisture absorption, which increased the weight of the specimens. Compared to the dry specimens, the weight of the specimen for 24 days increases to 5.2% and 7.89% for 35 days’ seawater ageing. The analysis also showed that due to seawater ageing, the de-bonding rate increased as the number of days increased.
Publisher: MDPI AG
Date: 08-2022
DOI: 10.3390/MA15155303
Abstract: This study investigates the comparison of the microstructural and mechanical properties of a novel ternary reinforced AA7075 hybrid metal matrix composite. Four s les, including AA7075 (base alloy), AA7075-5wt %SiC (MMC), AA7075-5wt %SiC-3wt %RHA (s-HMMC), and AA7075-5wt %SiC-3wt %RHA-1wt %CES (n-HMMC) were developed using the stir casting liquid metallurgy route, followed by the heat treatment. The experimental densities corresponded with the theoretical values, confirming the successful fabrication of the s les. A minimum density of 2714 kg/m3 was recorded for the n-HMMC. In addition, the highest porosity of 3.11% was found for n-HMMC. Furthermore, an increase of 24.4% in ultimate tensile strength and 32.8% in hardness of the n-HMMC was recorded compared to the base alloy. However, its ductility and impact strength was compromised with the lower values of 5.98% and 1.5 J, respectively. This was confirmed by microstructural analysis, which reveals that n-HMMC has mixing issues and forms agglomerates in the matrix, which served as the potential sites of stress concentration leading to low impact strength and ductility. Nevertheless, the hybrid composites showed superior mechanical properties over the MMC and its base alloy.
Publisher: MDPI AG
Date: 11-07-2021
DOI: 10.3390/MET11071103
Abstract: The integrity of machined holes depends on many parameters, some of which are related to the cutting tool (geometry, coating, material). Other influential parameters are related to the machining process variables (spindle speed, feed rate, workpiece material), all of which can affect the quality of the hole and drilling induced damage on its surface. This study investigates the effect of uncoated tools and four types of tool coatings (TiN-, TiCN-, TiAlN-, and TiSiN) on the hole quality and its microstructure. The study analyzed several hole geometrical metrics, namely hole size, circularity, cylindricity, and perpendicularity of an Al2024 aluminum alloy using a multi-spindle drilling process that utilizes three drills capable of creating multiple holes simultaneously. The results showed that the uncoated carbide drill gave a high-hole quality at low spindle speed. Regarding the coated drills, TiCN coated drills produced holes with the least deviation, circularity, cylindricity and perpendicularity at high spindle speeds. TiSiN–carbide coated drills produced the most oversized holes and noticeable damage and deformations on their surface following TiAlN and TiN. The common surface damage found on the inner hole surface was smearing, feed marks, and metal debris adhesion. The ANOVA results revealed that the tool type had the highest percentage contribution that mainly affected the hole quality.
Publisher: MDPI AG
Date: 28-06-2021
DOI: 10.3390/S21134432
Abstract: In this study, the burr and slot widths formed after the micro-milling process of Inconel 718 alloy were investigated using a rapid and accurate image processing method. The measurements were obtained using a user-defined subroutine for image processing. To determine the accuracy of the developed imaging process technique, the automated measurement results were compared against results measured using a manual measurement method. For the cutting experiments, Inconel 718 alloy was machined using several cutting tools with different geometry, such as the helix angle, axial rake angle, and number of cutting edges. The images of the burr and slots were captured using a scanning electron microscope (SEM). The captured images were processed with computer vision software, which was written in C++ programming language and open-sourced computer library (Open CV). According to the results, it was determined that there is a good correlation between automated and manual measurements of slot and burr widths. The accuracy of the proposed method is above 91%, 98%, and 99% for up milling, down milling, and slot measurements, respectively. The conducted study offers a user-friendly, fast, and accurate solution using computer vision (CV) technology by requiring only one SEM image as input to characterize slot and burr formation.
Publisher: MDPI AG
Date: 10-05-2021
DOI: 10.3390/APP11094285
Abstract: Drilling is one of the most performed machining operations for riveting and assembly operations in many industrial sectors. The accuracy of the drilled holes and their surface finish play a vital role in the longevity and performance of the machined components, which, in turn, increase productivity. Therefore, this study investigated the effect of the multi-spindle drilling process on dimensional hole tolerances, such as hole size, circularity, cylindricity, and perpendicularity. In addition, the surface defects formed in the holes were examined using scanning electron microscopy. Three aluminium alloys, AA2024, AA6061, and AA5083, which are commonly used in the aerospace, automotive, and marine sectors, were chosen as the study materials. The results showed that the holes drilled in AA2024 gave less circularity error, cylindricity error, and perpendicularity error. In the case of hole size, the holes drilled in AA6061 were less deviated from the nominal size following holes drilled in AA2024 and AA5083 alloys. Surface damage in the form of metal debris adhesion, smeared material, side flow, and feed marks was found on the inner hole surface. Holes drilled in AA5083 alloy had the worst surface finish and were the most oversized, which was associated with noticeable damage and deformations in their inner surface. The ANOVA results revealed that the spindle speed was more influential than feed and mainly affected the hole size and cylindricity errors. However, in the case of circularity error and perpendicularity error, drilling parameters were found to be insignificant.
Publisher: MDPI AG
Date: 06-08-2021
DOI: 10.3390/JRFM14080359
Abstract: This article reflects the main sources of risks for metallurgical enterprises in Russia, presenting the implementation of an innovative approach to increasing the competitiveness of an industrial enterprise, which is a typical representative of large enterprises of the metallurgical industry, based on the development of risk-oriented thinking when loading rolling mills with orders of intersecting assortment according to a new model. To reduce the emerging risks of a new model of the loading process of rolling mills of a metallurgical enterprise, it is proposed to take into account the risks in a complex way, taking into account their interactions with the use of integrated risk management (IRM). Practical development of the implemented approach was carried out by identifying the risks of the new improved loading process and their causes at each stage of the process. Risks were identified by analysis, qualitative and quantitative assessment of the likelihood of risks and the severity of consequences from their implementation with the establishment of events with a high potential hazard. Possible causes of hazardous events have been identified. To reduce the likelihood of unfavorable events, measures have been developed to influence significant risks and their effectiveness has been determined. The development of an innovative approach using risk-based thinking in a previously unexplored field of the application provides competitive advantages for enterprises of the metallurgical industry, increases income by reducing the cost of manufacturing products and production volumes by reducing time costs, achieving an economic efficiency of up to 10 million rubles per year. The practical significance of the dissemination of development results in similar industries is obvious and relevant for metallurgy as a whole.
Publisher: MDPI AG
Date: 05-07-2021
DOI: 10.3390/MET11071077
Abstract: SAC305 lead-free solder alloy is widely used in the electronic industry. However, the problems associated with the growth formation of intermetallic compounds need further research, especially at high temperatures. This study investigates the doping of Bismuth into SAC305 in the various compositions of 1, 2, and 3 wt.%. The microstructure in terms of intermetallic compound particles and mechanical properties was examined after thermal aging at temperatures of 100 °C and 200 °C for 60 h. The microstructure examination was observed using scanning electron microscopy, and the chemical composition of each alloy was confirmed with an energy dispersive X-ray. Tensile tests were performed to find the mechanical properties such as yield strength and ultimate tensile strength. The intermetallic compound’s phase analysis was identified using X-ray diffraction, and differential scanning calorimetry was done to study the temperature curves for melting points. Results showed that the addition of Bismuth refined the microstructure by suppressing the growth of intermetallic compounds, which subsequently improved the mechanical properties. The thermal aging made the microstructure coarsen and degraded the mechanical properties. However, the most improved performance was observed with a Bismuth addition of 3 wt.% into SAC305. Furthermore, a decrease in the melting temperature was observed, especially at Bismuth compositions of 3 wt.%.
Publisher: Elsevier BV
Date: 09-2020
Publisher: MDPI AG
Date: 27-06-2022
DOI: 10.3390/ENG3030022
Abstract: The cutting parameters in drilling operations are important for high-quality holes and productivity improvement in any manufacturing industry. This study investigates the effects of spindle speed and feed rate on temperature, surface roughness, hole size, circularity, and chip formation during dry drilling of gray cast iron ASTM A48. The results showed that the temperature increased as spindle speed and feed rate increased. The surface roughness had an inverse relationship with the spindle speed and direct relation with the feed rate. Furthermore, hole size increased with increased spindle speed and decreased as the feed rate increased, while hole circularity decreased with increasing both the spindle speed and feed rate. The analysis of variance (ANOVA) indicated that the spindle speed had the highest percentage contribution of 56.24% on temperature, followed by the feed rate with 42.35%. The surface roughness was highly influenced by the feed rate and the spindle speed with 55% and 44.12%, respectively. While the hole size was highly influenced by the feed rate with a 74.18% percentage contribution, and the contribution of spindle speed was 21.36%. In addition, the feed rate has a percentage contribution of 70.82% on circularity, which is higher than the spindle speed of 24.26% percentage contribution. The results also showed that thick and discontinuous chips were generated at higher feed rates, while long continuous chips were produced at high spindle speeds.
Publisher: Springer Science and Business Media LLC
Date: 06-10-2020
Publisher: MDPI AG
Date: 13-05-2022
Abstract: The current study focuses on minimising the bubbles in polyester-insulated ignition coils, which were produced with a defect level of ~21–25% or 210–250 coils per 1000 batch size by using the potting method. This high-level rejection makes a substantial financial impact by increasing waste material, manufacturing, and after-sales costs. Hence, to control the bubbled problem without using expensive and maintenance-heavy techniques, the process parameters in the potting method were alternated and investigated using one factor at a time, which played a vital role in the formation/reduction of bubbles in the ignition coil insulation. Process parameters, including pre rocess heating, the appropriate MEKP/cobalt naphthenate ratio, the pouring amount/increments, and the stirring speeds, reduced the bubble formation per lot from 205 ± 30 to 146 ± 25, 108 ± 21, 61 ± 17, and 10 ± 2 per 1000 lot accordingly. In addition, a comparative study was conducted in terms of performance and life cycle endurance, using Japanese and Indian standards. Furthermore, an after-sale warranty claim also supports the proposed changes in the potting technique. This modification may reduce the after-sales rejection within two years to approximately ~85%. This modification in the potting technique is extremely cost-effective in comparison to expensive processes, i.e., vacuum-pressure impregnation and vacuum impregnation, which require extensive labour and maintenance.
Publisher: MDPI AG
Date: 17-10-2021
DOI: 10.3390/EN14206764
Abstract: The present study investigates the thermo-hydraulic characteristics of a microchannel sink with novel trefoil Shaped ribs. The motivation for this form of rib shape is taken from the design of lung alveoli that exchange oxygen and carbon dioxide. This study has been conducted numerically by using a code from the commercially available Fluent software. The trefoil shaped ribs were mounted on the centerline of different walls of the microchannel in three different configurations. These consisted of base wall trefoil ribs (MC-BWTR), sidewall trefoil ribs (MC-SWTR), all wall trefoil ribs (MC-AWTR) and smooth channel (MC-SC) having no ribs on its wall. The streamline distance between the ribs was kept constant at 0.4 mm, and the results were compared by using pressure drop (∆p), Nusselt number (Nu), thermal resistance (Rth) and thermal enhancement factor (η). The results indicated that the addition of trefoil ribs to any wall improved heat transfer characteristics at the expense of an increase in the friction factor. The trends of the pressure drop and heat transfer coefficient were the same, which indicated higher values for MC-AWTR followed by MC-SWTR and a lower value for MC-BWTR. In order to compare the thermal and hydraulic performance of all the configurations simultaneously, the overall performance was quantified in terms of the thermal enhancement factor, which was higher than one in each case, except for MC-AWTR, in 100 Re 200 regimes. The thermal enhancement factor in the ribbed channel was the highest for MC-SWTR followed by MC-BWTR, and it was the lowest for MC-AWTR. Moreover, the thermal enhancement factor increases with the Reynolds number (Re) for each case. This confirms that the increment in the Nusselt number with velocity is more significant than the pressure drop. The highest thermal enhancement factor of 1.6 was attained for MC-SWTR at Re = 1000, and the lowest value of 0.87 was achieved for MC-AWTR at Re = 100.
Publisher: MDPI AG
Date: 23-05-2021
DOI: 10.3390/MET11060854
Abstract: Drilling is an important machining process in various manufacturing industries. High-quality holes are possible with the proper selection of tools and cutting parameters. This study investigates the effect of spindle speed, feed rate, and drill diameter on the generated thrust force, the formation of chips, post-machining tool condition, and hole quality. The hole surface defects and the top and bottom edge conditions were also investigated using scan electron microscopy. The drilling tests were carried out on AA2024-T3 alloy under a dry drilling environment using 6 and 10 mm uncoated carbide tools. Analysis of Variance was employed to further evaluate the influence of the input parameters on the analysed outputs. The results show that the thrust force was highly influenced by feed rate and drill size. The high spindle speed resulted in higher surface roughness, while the increase in the feed rate produced more burrs around the edges of the holes. Additionally, the burrs formed at the exit side of holes were larger than those formed at the entry side. The high drill size resulted in greater chip thickness and an increased built-up edge on the cutting tools.
Location: United Kingdom of Great Britain and Northern Ireland
Location: United Kingdom of Great Britain and Northern Ireland
Location: United Kingdom of Great Britain and Northern Ireland
Location: United Kingdom of Great Britain and Northern Ireland
No related grants have been discovered for Khaled Giasin.