ORCID Profile
0000-0002-5488-0897
Current Organisations
Edith Cowan University
,
Bangladesh Atomic Energy Commission
Does something not look right? The information on this page has been harvested from data sources that may not be up to date. We continue to work with information providers to improve coverage and quality. To report an issue, use the Feedback Form.
Publisher: AIP Publishing
Date: 07-2019
DOI: 10.1063/1.5109003
Abstract: Monocrystalline silicon solar cells with photo-absorbing morphology can lify light-trapping properties within the absorber layer and help to fabricate cost-effective solar cells. In this paper, the effect of different parameters namely temperature and time of Cu-assisted chemical etching was thoroughly investigated for the optimization of the light absorption properties. P-type monocrystalline wafers were selectively treated with Cu(NO3)2.3H2O:HF:H2O2:DI water solution at 50 °C for five different time duration. The entire process was repeated at five different temperatures for 20min as well to study the relation between etching temperature and surface reflectance. Sonication bathing was used for the removal of the deposited Cu atoms from the surface with the variation of time and the effect was examined using energy dispersive spectroscopy (EDS). Field emission scanning electron microscopy (FESEM) and UV/VIS spectroscopy were conducted to study the surface morphology and light absorbance respectively. Inverted shapes almost similar to inverted pyramids or porous surface were found randomly on the surface of the wafer. The effect of temperature was found more significant compared to the effect of time variation. An optimum light reflectance was found at 50 °C for 20 min of texturization. Atomic force microscopy (AFM) of the textured s le revealed the average depth of pyramidal shape was about 1.58 μm. EDS results showed a proportional relation between time and Cu removal process, and a complete Cu atoms free textured surface after 25 min of sonication bathing. Therefore, a suitable Cu-assisted texturization technique was found, which could enable lowering the photo-reflectance below 1% without any antireflection coating.
Publisher: IEEE
Date: 04-2014
Publisher: IOP Publishing
Date: 22-02-2019
Publisher: Elsevier BV
Date: 2019
Publisher: MDPI AG
Date: 20-05-2021
DOI: 10.20944/PREPRINTS202105.0486.V1
Abstract: This research project focuses on the optimization of the hybrid energy system together with the assistance of thin-film coatings aiming to achieve self-sustainable food and crop storage facilities which will run effectively with its own generated energy. An infrastructure will be designed and constructed that will comprise a hybrid power generation system accompanied by thin-film coated semitransparent and non-transparent construction materials for energy saving. Thin-film low emissivity (Low-E) type coatings will assist the transparent or semitransparent construction materials to reflect most of the infrared (IR-mostly heat) and UV spectra of sunlight without interrupting the visible spectrum and will lead to saving energy consumption by reducing the heat and lighting during day time
Publisher: MDPI AG
Date: 04-01-2023
DOI: 10.3390/FUTURETRANSP3010005
Abstract: Bangladesh’s railway system mostly uses typical manual railway crossing techniques or boom gates through its 2955.53 km rail route all over the country. Accidents frequently happen at railway crossings due to the lack of quickly operating gate systems, and to fewer safety measures at the railway crossing as well. Currently, there are very few automatic railway crossing systems available (without obstacle detectors). Additionally, all of them are dependent on the national power grid, without a backup plan for any emergency cases. Bangladesh is still running a bit behind in generating enough power for its consumption hence, it is not possible to have a continuous power supply at all times all over the countryside. We aim to design and develop a smart railway crossing system with an obstacle detector to prevent common types of accidents at railway crossing points. We use two infrared (IR) sensors to operate the railway crossing systems, which are controlled by an Arduino Uno. This newly designed level crossing system is run with the help of sustainable renewable energy, which is cost-effective and eco-friendly, and applied under the national green energy policy towards achieving sustainable development in Bangladesh as a part of the global sustainable goal to face climate change challenges. We have summarized the simulated the results of several renewable energy sources, including a hybrid system, and optimized the Levelized Cost of Energy (LCOE) and the payback periods.
Publisher: Elsevier BV
Date: 02-2019
Publisher: IEEE
Date: 10-2018
Publisher: MDPI AG
Date: 03-02-2022
DOI: 10.20944/PREPRINTS202202.0060.V1
Abstract: Bangladesh's railway system mostly uses typical manual railway crossing technique or boom gates through its 2,955.53 km rail route all over the country. The accidents are frequently happening in the railway crossings due to not having obstacle detectable and quickly operating gate systems, and also for fewer safety measures in the railway crossing. Currently, there are very few automatic railway crossing systems (without obstacle detectors) available, however, all of them are dependent on the national power grid without a backup plan for any emergency cases. Bangladesh is still running a bit behind in the power generation of its consumption, hence it is not possible to have a continuous power supply at all times all over the countryside. We aim to design and develop a smart railway crossing system with an obstacle detector to prevent common types of accidents in the railway crossing points. We design to use two infrared (IR) sensors to operate the railway crossing systems which will be controlled by the Arduino Uno. This newly designed level crossing system will be run with the help of sustainable renewable energy which is cost-effective, eco-friendly, and apply under the national green energy policy towards achieving sustainable development in Bangladesh as a part of the global sustainable goal to face climate change challenges. We have summarized the simulated results of several renewable energy sources including a hybrid system and optimized the Levelized Cost of Energy (LCOE), and the payback periods.
Publisher: Springer Science and Business Media LLC
Date: 08-05-2018
Publisher: Elsevier BV
Date: 10-2018
Publisher: Elsevier BV
Date: 09-2018
Publisher: MDPI AG
Date: 19-07-2021
DOI: 10.20944/PREPRINTS202107.0413.V1
Abstract: Metallic thin-film materials and nanoparticles (mainly Silver (Ag)-based) are recently being used in many nano-technological applications including sensors, reflective heat-mirror coatings, and antibacterial coatings as well. The physical vapor deposition technique attracts significant attention for Ag-based nanocomposites with tailoring the structural and optical properties of metallic thin films thus allowing further improvements and application possibilities in various existing fields namely electronics, catalysis, magnetics, optics in alongside the environment and health and new emergent fields in, particularly thin-film coatings. This study highlights the preparation, characterization, properties, and possible future application directions of several types of Silver (Ag)-based nanocomposite thin films prepared by using physical vapor deposition techniques.
Publisher: MDPI AG
Date: 04-04-2022
DOI: 10.3390/SU14074278
Abstract: The building integrated photovoltaic (BIPV) system is one of the contributors which has enormous potential to reach the goal of net-zero energy buildings (NZEB) that significantly reduce the use of fossil fuels that contribute to global warming. However, the limitations of the visual and aesthetic appearance of current BIPV systems make this aspiration unlikely. This study investigates the limitations of the single-color-based PV modules that are dull in appearance and have low photo-conversion efficiency (PCE). In order to solve this issue, we designed, developed, and characterized micro-patterned-based multicolored photovoltaic (MPCPV) modules which are applicable to net-zero building and development. Our newly developed MPCPV module exhibits an aesthetically attractive and flexible building color suitable for industrial application. Furthermore, the MPCPV module possesses an efficiency of 9.6%, which is 4.1% higher than a single-color PV module (5.5%) but closer to conventional thin-film PV modules. In addition, the other output parameters, such as short-circuit current (Isc), open-circuit voltage (Voc), maximum power (Pmax), and fill factor (FF), indicate that our developed colored PV module is suitable for modern infrastructures that will enable energy generation on-site without compromising the aesthetic appearance. Finally, this research will have a substantial influence on the NZEB and will play an important part in the development of a sustainable environment.
Publisher: MDPI AG
Date: 17-10-2020
DOI: 10.3390/SU12208609
Abstract: This paper reports on the optimization of thin-film coating-assisted, self-sustainable, off-grid hybrid power generation systems for cattle farming in rural areas of Bangladesh. Bangladesh is a lower middle-income country with declining rates of poverty among its 160 million people due to persistent economic growth in conjunction with balanced agricultural improvements. Most of the rural households adopt a mixed farming system by cultivating crops and simultaneously rearing livestock. Among the animals raised, cattle are considered as the most valuable asset for the small-/medium-scale farmers in terms of their meat and milk production. Currently, along with the major health issue, the COVID-19 pandemic is hindering the world’s economic growth and has thrust millions into unemployment Bangladesh is also in this loop. However, natural disasters such as COVID-19 pandemic and floods, largely constrain rural smallholder cattle farmers from climbing out of their poverty. In particular, small- and medium-scale cattle farmers face many issues that obstruct them from taking advantage of market opportunities and imposing a greater burden on their families and incomes. An appropriate measure can give a way to make those cattle farmers’ businesses both profitable and sustainable. Optimization of thin-film coating-assisted, self-sustainable, off-grid hybrid power generation system for cattle farming is a new and forward-looking approach for sustainable development of the livestock sector. In this study, we design and optimize a thin-film coating-assisted hybrid (photovoltaic battery generator) power system by using the Hybrid Optimization of Multiple Energy Resources (HOMER, Version 3.14.0) simulation tool. An analysis of the results has suggested that the off-grid hybrid system is more feasible for small- and medium-scale cattle farming systems with long-term sustainability to overcome the significant challenges faced by smallholder cattle farmers in Bangladesh.
Publisher: Walter de Gruyter GmbH
Date: 20-10-2017
Abstract: Zinc oxide thin films with different thicknesses were prepared on microscopic glass slides by sol-gel spin coating method, then hydrothermal process was applied to produce zinc oxide nanorod arrays. The nanorod thin films were characterized by various spectroscopic methods of analysis. From the images of field emission scanning electron microscope (FESEM), it was observed that for the film thickness up to 200 nm the formed nanorods with wurtzite hexagonal structure were uniformly distributed over the entire surface substrate. From X-ray diffraction analysis it was revealed that the thin films had good polycrystalline nature with highly preferred c-axis orientation along (0 0 2) plane. The optical characterization done by UV-Vis spectrometer showed that all the films had high transparency of 83 % to 96 % in the visible region and sharp cut off at ultraviolet region of electromagnetic spectrum. The band gap of the films decreased as their thickness increased. Energy dispersive X-ray spectroscopy (EDS) showed the presence of zinc and oxygen elements in the films and Fourier transform infrared spectroscopy (FT-IR) revealed the chemical composition of ZnO in the film.
Publisher: Elsevier BV
Date: 2019
Publisher: MDPI AG
Date: 22-07-2021
DOI: 10.3390/APP11156746
Abstract: Metallic thin-film materials and nanoparticles (mainly silver (Ag)-based) are recently being used in many nano-technological applications, including sensors, reflective heat-mirror coatings, and antibacterial coatings. The physical vapor deposition technique has attracted significant attention for Ag-based nanocomposites with tailoring of the structural and optical properties of metallic thin films, thus allowing for further improvements and application possibilities in various existing fields, namely electronics, catalysis, magnetics, and optics, alongside the environment and health and new emergent fields, particularly thin-film coatings. This study highlights the preparation, characterization, properties, and possible future application directions of several types of silver (Ag)-based nanocomposite thin films prepared by using physical vapor deposition techniques. The high-temperature (above 300 °C) heat-treated composite layer shows significant spectral shifts however, distinguishingly notable sizes of nanoparticles are not observed, which indicates that this newly developed composite material can be useful for various coating applications.
Publisher: Elsevier BV
Date: 12-2018
Publisher: IOP Publishing
Date: 10-05-2019
Publisher: Elsevier BV
Date: 11-2018
Publisher: MDPI AG
Date: 25-03-2023
DOI: 10.3390/BUILDINGS13040863
Abstract: With the sharp increase in global energy demand, industrial and residential buildings are responsible for around 40% of the energy consumed with most of this energy portion being generated by non-renewable sources, which significantly contribute to global warming and environmental hazards. The net-zero energy building (NZEB) concept attempts to solve the global warming issue, whereby a building will produce, on-site, its required energy demand throughout the year from renewable energy sources. This can be achieved by integrating photovoltaic (PV) building materials, called building-integrated photovoltaic (BIPV) modules, throughout the building skin, which simultaneously act as construction materials and energy generators. Currently, architects and builders are inclined to design a building using BIPV modules due to the limited colors available, namely, black or blue, which result in a monotonous building appearance. Therefore, there is an increasing demand/need to develop modern, aesthetically pleasing BIPV green energy products for the use of architects and the construction industry. This review article presents the current stage and future goal of advanced building integrated photovoltaic systems, focusing on the aesthetically appealing BIPV systems, and their applications towards overcoming global challenges and stepping forward to achieve a sustainable green energy building environment. Additionally, we present the summary and outlook for the future development of aesthetically appealing building integrated photovoltaic systems.
Location: Bangladesh
No related grants have been discovered for M. Khairul Basher.