ORCID Profile
0000-0002-2679-8394
Current Organisation
Flinders University
Does something not look right? The information on this page has been harvested from data sources that may not be up to date. We continue to work with information providers to improve coverage and quality. To report an issue, use the Feedback Form.
In Research Link Australia (RLA), "Research Topics" refer to ANZSRC FOR and SEO codes. These topics are either sourced from ANZSRC FOR and SEO codes listed in researchers' related grants or generated by a large language model (LLM) based on their publications.
Biomechanical Engineering | Biomedical Engineering | Palaeontology (incl. Palynology) | Medical Devices | Biomaterials | Structural Engineering
Expanding Knowledge in Engineering | Education and Training Systems not elsewhere classified | Expanding Knowledge in the Agricultural and Veterinary Sciences | Expanding Knowledge in the Medical and Health Sciences | Metals (e.g. Composites, Coatings, Bonding) |
Publisher: Elsevier BV
Date: 03-2021
Publisher: Wiley
Date: 05-2010
DOI: 10.1111/J.1365-2818.2009.03338.X
Abstract: The aim of this work was to present and discuss a quality control protocol for in vitro micro-computed tomography (microCT), based on the adaptation of the quality control protocols for medical computed tomography. The importance of establishing a quality control protocol is related to the opportunity to identify problems on time comparing the microCT images acquired in different time points, and in this way to verify the performance of the device. The proposed quality control protocol was applied for a long-time monitoring period to verify the stability of the micro-tomographic system over time. The protocol proposed in this study was applied to the histomorphometric characterization of bone tissue, but it can be used on a wide range of in vitro microCT applications. Noise and uniformity tests, taken and adapted to micro-tomographic system by medical standard guidelines of quality control, were performed by the use of a water phantom. An accuracy test was designed and performed by the use of a morphometric calibrated phantom. All these tests were performed during a long-time monitoring period to control the stability of the system. Specific control charts and monitoring parameters for each test were used to represent the monthly measures collected during 20 months and an out of control condition was defined. The reference values (baseline), calculated to control the stability of micro-tomographic system over time, were calculated during acceptance/status test. During the period, no out of control conditions in noise, uniformity and accuracy tests were recorded. However, a changing condition was found in noise test, as showed by using statistical C (P < 0.01) and Kruskal-Wallis (P < 0.05) tests. In particular, a Wilcoxon rank sum test with Bonferroni correction (P < 0.0125) was applied in noise test to investigate which of the comparisons among first five acquisitions of year 2004 (group B.L.) and each group was significant (P < 0.0125). The noise showed a slight but significant increase over the years compared to baseline value however, no out of control conditions were recorded. Nonetheless, a maintenance service to control the performance of mechanical components of microCT was required and performed.
Publisher: Wiley
Date: 10-03-2014
DOI: 10.1002/JOR.22611
Abstract: Kienböck's disease is idiopathic osteonecrosis of the lunate, leading to its fracture and collapse. This study compares internal and external bone micro-architecture of normal and fractured lunates (Kienböck's), by using high-resolution three-dimensional (3D) micro-computed tomography (micro-CT) on the whole bone of the two lunate types, and histology. Fractured Kienböck-diseased lunates were obtained from patients undergoing proximal-row-carpectomy, while normal cadaveric lunates served as controls. 3D-micro-CT-imaging of control lunates revealed an encircling cortex surrounding trabecular bone. Trabeculae were arranged in a radial pattern, spanning from the distal to the proximal subchondral plate. Kienböck's lunates exhibited clear fracture lines, with fragmented bone, both proximally and distally, in areas the radially-patterned trabeculae and enveloping cortex were absent, producing height loss. In trabecular bone, Kienböck's lunates revealed increased bone volume fraction, trabecular thickness and number, and decreased trabecular separation and structure model index. Histologically, Kienböck's lunates revealed osteonecrosis, as well as remodeling fronts with osteoblasts and osteoid surrounding bone marrow. Whole-bone high-resolution 3D examination of normal and Kienböck's diseased lunates contributes to a better understanding of micro-architectural changes occurring in the pathology.
Publisher: Wiley
Date: 30-04-2021
DOI: 10.1002/JOR.25051
Abstract: The objectives of this study were to (1) develop a semiautomated method to obtain lesion volume and bone mineral density (BMD) in terms of Hounsfield units from pelvic computed tomography (CT) scans in three regions of interest, and (2) assess accuracy and reliability of the method based on cadaveric CT scans. Image artefacts due to metal implants reduce CT clarity and are more severe with more than one implant in situ. Therefore, accuracy and reliability tests were performed with varying numbers of total hip arthroplasties implanted. To test the accuracy of lesion size measurements, microcomputed tomography was used as a reference. Mean absolute error ranged from 36 to 284 mm 3 after five measurements. Intra‐ and inter‐operator reliability of the entire method was measured for a selection of parameters. All coefficient of variation values were good to excellent for CT scans of the native pelvic anatomy and a CT scans of the same pelvis with one and two implants in situ. Accuracy of quantifying lesion volume decreased with decreasing CT image clarity by 0.6%–3.6% mean absolute relative error. Reliability of lesion volume measurement decreased with decreasing CT clarity. This was also the case for reliability of BMD measurements in the region most disrupted by metal artefact. The presented method proposes an approach for quantifying bone loss which has been proven to be accurate, reliable, and clinically applicable.
Publisher: BMJ
Date: 29-06-2017
Publisher: Springer Science and Business Media LLC
Date: 12-11-2021
DOI: 10.1007/S10439-020-02682-Y
Abstract: We hypothesize that variations of body anthropometry, conjointly with the bone strength, determine the risk of hip fracture. To test the hypothesis, we compared, in a simulated sideways fall, the hip impact energy to the energy needed to fracture the femur. Ten femurs from elderly donors were tested using a novel drop-tower protocol for replicating the hip fracture dynamics during a fall on the side. The impact energy was varied for each femur according to the donor’s body weight, height and soft-tissue thickness, by adjusting the drop height and mass. The fracture pattern, force, energy, strain in the superior femoral neck, bone morphology and microarchitecture were evaluated. Fracture patterns were consistent with clinically relevant hip fractures, and the superior neck strains and timings were comparable with the literature. The hip impact energy (11 – 95 J) and the fracture energy (11 – 39 J) ranges overlapped and showed comparable variance (CV = 69 and 61%, respectively). The aBMD-based definition of osteoporosis correctly classified 7 (70%) fracture/non-fracture cases. The incorrectly classified cases presented large impact energy variations, morphology variations and large subcortical voids as seen in microcomputed tomography. In conclusion, the risk of osteoporotic hip fracture in a sideways fall depends on both body anthropometry and bone strength.
Publisher: Elsevier BV
Date: 03-2014
DOI: 10.1016/J.JBIOMECH.2014.01.001
Abstract: Digital volume correlation (DVC) provides experimental measurements of displacements and strains throughout the interior of porous materials such as trabecular bone. It can provide full-field continuum- and tissue-level measurements, desirable for validation of finite element models, by comparing image volumes from subsequent µCT scans of a s le in unloaded and loaded states. Since the first application of DVC for measurement of strain in bone tissue, subsequent reports of its application to trabecular bone cores up to whole bones have appeared within the literature. An "optimal" set of procedures capable of precise and accurate measurements of strain, however, still remains unclear, and a systematic review focussing explicitly on the increasing number of DVC algorithms applied to bone or structurally similar materials is currently unavailable. This review investigates the effects of in idual parameters reported within in idual studies, allowing to make recommendations for suggesting algorithms capable of achieving high accuracy and precision in displacement and strain measurements. These recommendations suggest use of subsets that are sufficiently large to encompass unique datasets (e.g. subsets of 500 µm edge length when applied to human trabecular bone cores, such as cores 10mm in height and 5mm in diameter, scanned at 15 µm voxel size), a shape function that uses full affine transformations (translation, rotation, normal strain and shear strain), the robust normalized cross-correlation coefficient objective function, and high-order interpolation schemes. As these employ computationally burdensome algorithms, researchers need to determine whether they have the necessary computational resources or time to adopt such strategies. As each algorithm is suitable for parallel programming however, the adoption of high precision techniques may become more prevalent in the future.
Publisher: Elsevier BV
Date: 2008
DOI: 10.1016/J.JBIOMECH.2007.08.003
Abstract: Human cancellous bone is a heterogeneous material. Despite this, most of the published studies report correlations between mechanical properties and morphometric parameters averaged on the whole specimen. This work investigated whether local variations in morphometric parameters were linked to the localized failure regions of cancellous bone. Additionally, it was examined whether local values of morphometric parameters can predict the ultimate stress better than the average bone volume fraction (BV/TV). Cylindrical cancellous bone specimens extracted along the primary compressive group of human femoral heads were studied. These were microCT-imaged to assess the morphometric parameters, compressed to determine the ultimate stress, and rescanned by microCT to visualize the failure region. Failure involved slightly less than half of the free height of the specimens. Significant differences were found in the morphometric parameters calculated in the failure and in the non-failure regions. The cross-sections containing minimum BV/TV values were those most often located inside the failure region (83%, p<0.001). Regression analysis confirmed that variations in BV/TV best describe variations in ultimate stress (R2=0.84) out of the averaged morphometric parameters. The prediction of ultimate stress increased when minimum or maximum values of the morphometric parameters were taken, with the highest prediction found by considering the minimum BV/TV (R2=0.95). In conclusion, due to the heterogeneity of cancellous bone, there may exist regions characterized by a different microarchitecture, where the bone is weaker and consequently is more likely to fail. These regions mostly contain minimum values in BV/TV, which were found to predict ultimate stress better than average BV/TV.
Publisher: Scandinavian Journal of Work, Environment and Health
Date: 18-07-2019
DOI: 10.5271/SJWEH.3754
Publisher: Wiley
Date: 28-11-2017
DOI: 10.1002/JOR.23474
Abstract: Tibial subchondral bone plays an important role in knee osteoarthritis (OA). Microarchitectural characterization of subchondral bone plate (SBP), underlying subchondral trabecular bone (STB) and relationships between these compartments, however, is limited. The aim of this study was to characterize the spatial distribution of SBP thickness, SBP porosity and STB microarchitecture, and relationships among them, in OA tibiae of varying joint alignment. Twenty-five tibial plateaus from end-stage knee-OA patients, with varus (n = 17) or non-varus (n = 8) alignment were micro-CT scanned (17 μm/voxel). SBP and STB microarchitecture was quantified via a systematic mapping in 22 volumes of interest per knee (11 medial, 11 lateral). Significant within-condylar and between-condylar (medial vs. lateral) differences (p < 0.05) were found. In varus, STB bone volume fraction (BV/TV) was consistently high throughout the medial condyle, whereas in non-varus, medially, it was more heterogeneously distributed. Regions of high SBP thickness were co-located with regions of high STB BV/TV underneath. In varus, BV/TV was significantly higher medially than laterally, however, not so in non-varus. Moreover, region-specific significant associations between the SBP thickness and SBP porosity and the underlying STB microarchitecture were detected, which in general were not captured when considering the values averaged for each condyle. As subchondral bone changes reflect responses to local mechanical and biochemical factors within the joint, our results suggest that joint alignment influences both the medial-to-lateral and the within-condyle distribution of force across the tibia, generating corresponding local bony responses (adaptation) of both the subchondral bone plate and underlying subchondral trabecular bone microarchitecture. © 2016 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 35:1927-1941, 2017.
Publisher: Elsevier BV
Date: 10-2010
DOI: 10.1016/J.JOCA.2010.07.005
Abstract: This study examined differential gene expression, histomorphometric indices and relationships between these, in femoral trabecular bone from osteoarthritis (OA) patients and control (CTL) subjects, with the aim of identifying potential molecular drivers consistent with changes in structural and remodelling indices in the OA pathology. Bone s les from the intertrochanteric (IT) region were obtained from age and sex-matched cohorts of 23 primary hip OA patients and 21 CTL subjects. Real-time polymerase chain reaction (PCR) and histomorphometric analysis were performed on each s le and correlations between gene expression and histomorphometric variables determined. Alterations in gene expression, structural indices and correlations between these were found in OA bone compared to CTL. In OA bone, expression of critical regulators of osteoblast differentiation (TWIST1) and function (PTEN, TIMP4) were decreased, while genes associated with inflammation (SMAD3, CD14) were increased. Bone structural and formation indices (BV/TV, Tb.N, OS/BS) were increased, whereas resorption indices (ES/BS, ES/BV) were decreased. Importantly, significant correlations in CTL bone between CTNNB1 expression and formation indices (OS/BS, OS/BV, OV/BV) were absent in OA bone, indicating altered WNT/β-catenin signalling. TWIST1 expression and BV/TV were correlated in CTL bone, but not in OA bone, consistent with altered osteoblastogenesis in OA. Matrix metalloproteinase 25 (MMP25) expression and remodelling indices (ES/BS, ES/BV, ES/TV) were correlated only in OA pointing to aberrant bone remodelling in this pathology. These findings indicate an altered state of osteoblast differentiation and function in OA driven by several key molecular regulators. In association with this differential gene expression, an altered state of both trabecular bone remodelling and resulting microarchitecture were also observed, further characterising the pathogenesis of primary hip OA.
Publisher: Elsevier BV
Date: 02-2008
DOI: 10.1016/J.CLINBIOMECH.2007.08.024
Abstract: In many published studies, elastic properties of bone are correlated to the bone density, in order to derive an empirical elasticity-density relationship. The most common use of these relationships is the prediction of the bone local properties from medical imaging data in subject-specific numerical simulation studies. The proposed relationships are substantially different one from the other. It is unclear whether such differences in elasticity-density relationships can be entirely explained in terms of methodological discrepancies among studies. All relevant literature was reviewed. Only elasticity-density relationships derived from similarly controlled experiments were included and properly normalized. The resulting relationships were grouped according to the most important methodological differences: type of end support during testing, specimen geometry, and anatomical s ling location. Even after normalization with respect to strain rate and densitometric measurement unit, substantial inter-study differences do exist, and they can only be partially explained by the methodological differences between studies. Some recommendations are made for the application of elasticity-density relationships to subject-specific finite element studies. The importance of defining a standardized mechanical testing methodology for bone specimens is stressed, and some guidelines that emerged from the literature are proposed. To identify density-elasticity relationships suitable for use in subject-specific FE studies, the development of a benchmark study is also proposed, where the elasticity-density relationship is taken as the variable under study, and a numerical model of known numerical accuracy predicts experimental strain measurements.
Publisher: Scandinavian Journal of Work, Environment and Health
Date: 25-09-2017
DOI: 10.5271/SJWEH.3671
Abstract: Objectives Work-related musculoskeletal disorders (MSD) are highly prevalent and put a large burden on (working) society. Primary prevention of work-related MSD focuses often on physical risk factors (such as manual lifting and awkward postures) but has not been too successful in reducing the MSD burden. This may partly be caused by insufficient knowledge of etiological mechanisms and/or a lack of adequately feasible interventions (theory failure and program failure, respectively), possibly due to limited integration of research disciplines. A research framework could link research disciplines thereby strengthening the development and implementation of preventive interventions. Our objective was to define and describe such a framework for multi-disciplinary research on work-related MSD prevention. Methods We described a framework for MSD prevention research, partly based on frameworks from other research fields (ie, sports injury prevention and public health). Results The framework is composed of a repeated sequence of six steps comprising the assessment of (i) incidence and severity of MSD, (ii) risk factors for MSD, and (iii) underlying mechanisms and the (iv) development, (v) evaluation, and (vi) implementation of preventive intervention(s). Conclusions In the present framework for optimal work-related MSD prevention, research disciplines are linked. This framework can thereby help to improve theories and strengthen the development and implementation of prevention strategies for work-related MSD.
Publisher: Springer Science and Business Media LLC
Date: 03-2011
Publisher: Elsevier BV
Date: 07-2011
DOI: 10.1016/J.CLINBIOMECH.2011.01.010
Abstract: The mechanical characterization of trabecular bone is related to its structure. In order to describe the trabecular structure and to study the mechanical behavior of the trabecular tissue, several parameters are presented in the literature. Some studies suggest a possible dependence of the structure on bone volume fraction this dependence could bias the validity of previous studies. The problem increases its complexity when pathological bone such as osteoarthritic tissue is studied, where the organization of the trabecular structure could be different if compared to the non-pathological tissue. The primary aim of this study was to evaluate the dependence between trabecular structure and bone volume fraction. The secondary aim was to compare osteoarthritic and non-pathological bone considering the correlation between structure and bone volume fraction. Sixty trabecular bone specimens were extracted from femoral heads of two groups of 30 Caucasian donors an osteoarthritic group and a non-pathological group. Several structural parameters, such as bone volume fraction, direct trabecular thickness, fabric tensor eigenvalues and their normalizations, were calculated from micro-CT analysis. A statistical analysis was carried out to identify the dependences between structural parameters and bone volume fraction. The comparison between osteoarthritic bone and non-pathological bone was also performed. Only the normalized eigenvalues of the fabric tensor were not correlated to bone volume fraction (R<0.5). The first and second normalized eigenvalues were significantly different between osteoarthritic bone and non-pathological bone (respectively P<0.05 and P<0.001). In conclusion, orientation and anisotropy of the trabecular structure do not depend on bone volume fraction. Moreover, differences in the first and second normalized fabric tensor eigenvalues suggest in the osteoarthritic group a structure more oriented along the main trabecular direction.
Publisher: MDPI AG
Date: 12-10-2020
Abstract: Childcare workers are reported to have high variation in physical activity during work hours, but also to sit for about half of the workday and have almost no high intensity physical activity (HIPA). No study has investigated if their work can be re-designed to introduce HIPA, thus promoting fitness and health according to the Goldilocks principle. This study investigated the feasibility of designing pedagogical games (‘Goldilocks-games’) intended to lead to more HIPA. Heart rate was measured in nineteen childcare workers during Goldilocks-games, and compared to measurements during a regular workday. Worker perceptions of feasibility, and researcher observations of contextual factors were also collected. The Goldilocks-games (33 min) elicited significantly more HIPA (18/33 min) compared to the most active period of equal length on a regular workday (0.5/33 min). Seventy-four-percent of the childcare workers reported that it was feasible to integrate the Goldilocks-games pedagogically, and seventy-two-percent could see themselves using them. Thus, we found it possible to re-design a work task in childcare according to the Goldilocks principle so that it leads to substantial time with HIPA. The sustainability of Goldilocks-games in childcare, and their effectiveness in improving fitness and health among childcare workers, needs to be tested in further studies.
Publisher: Elsevier BV
Date: 04-2018
DOI: 10.1016/J.JOCA.2018.01.014
Abstract: To study, in end-stage knee osteoarthritis (OA) patients, relationships between indices of in vivo dynamic knee joint loads obtained pre-operatively using gait analysis, static knee alignment, and the subchondral trabecular bone (STB) microarchitecture of their excised tibial plateau quantified with 3D micro-CT. Twenty-five knee OA patients scheduled for total knee arthroplasty underwent pre-operative gait analysis. Mechanical axis deviation (MAD) was determined radiographically. Following surgery, excised tibial plateaus were micro-CT-scanned and STB microarchitecture analysed in four subregions (anteromedial, posteromedial, anterolateral, posterolateral). Regional differences in STB microarchitecture and relationships between joint loading and microarchitecture were examined. STB microarchitecture differed among subregions (P < 0.001), anteromedially exhibiting highest bone volume fraction (BV/TV) and lowest structure model index (SMI). Anteromedial BV/TV and SMI correlated strongest with the peak external rotation moment (ERM r = -0.74, r = 0.67, P < 0.01), despite ERM being the lowest (by factor of 10) of the moments considered, with majority of ERM measures below accuracy thresholds medial-to-lateral BV/TV ratios correlated with ERM, MAD, knee adduction moment (KAM) and internal rotation moment (|r|-range: 0.54-0.74). When controlling for walking speed, KAM and MAD, the ERM explained additional 11-30% of the variations in anteromedial BV/TV and medial-to-lateral BV/TV ratio (R This preliminary study suggests significant associations between tibial plateau STB microarchitecture and knee joint loading indices in end-stage knee OA patients. Particularly, anteromedial BV/TV correlates strongest with ERM, whereas medial-to-lateral BV/TV ratio correlates strongest with indicators of medial-to-lateral joint loading (MAD, KAM) and rotational moments. However, associations with ERM should be interpreted with caution.
Publisher: Wiley
Date: 17-01-2014
DOI: 10.1002/JBMR.2090
Abstract: The molecular networks controlling bone homeostasis are not fully understood. The common evolution of bone and adaptive immunity encourages the investigation of shared regulatory circuits. MHC Class II Transactivator (CIITA) is a master transcriptional co-activator believed to be exclusively dedicated for antigen presentation. CIITA is expressed in osteoclast precursors, and its expression is accentuated in osteoporotic mice. We thus asked whether CIITA plays a role in bone biology. To this aim, we fully characterized the bone phenotype of two mouse models of CIITA overexpression, respectively systemic and restricted to the monocyte-osteoclast lineage. Both CIITA-overexpressing mouse models revealed severe spontaneous osteoporosis, as assessed by micro-computed tomography and histomorphometry, associated with increased osteoclast numbers and enhanced in vivo bone resorption, whereas osteoblast numbers and in vivo bone-forming activity were unaffected. To understand the underlying cellular and molecular bases, we investigated ex vivo the differentiation of mutant bone marrow monocytes into osteoclasts and immune effectors, as well as osteoclastogenic signaling pathways. CIITA-overexpressing monocytes differentiated normally into effector macrophages or dendritic cells but showed enhanced osteoclastogenesis, whereas CIITA ablation suppressed osteoclast differentiation. Increased c-fms and receptor activator of NF-κB (RANK) signaling underlay enhanced osteoclast differentiation from CIITA-overexpressing precursors. Moreover, by extending selected phenotypic and cellular analyses to additional genetic mouse models, namely MHC Class II deficient mice and a transgenic mouse line lacking a specific CIITA promoter and re-expressing CIITA in the thymus, we excluded MHC Class II expression and T cells from contributing to the observed skeletal phenotype. Altogether, our study provides compelling genetic evidence that CIITA, the molecular switch of antigen presentation, plays a novel, unexpected function in skeletal homeostasis, independent of MHC Class II expression and T cells, by exerting a selective and intrinsic control of osteoclast differentiation and bone resorption in vivo.
Publisher: Wiley
Date: 18-04-2016
DOI: 10.1002/JBM.B.33682
Abstract: A major complication of silicone breast implants is the formation of a capsule around the implant known as capsular contracture which results in the distortion of the implant. Recently, a mouse model for studying capsular contracture was examined using micro-computed tomography (micro-CT), however, only qualitative changes were reported. The aim of this study was to develop a quantitative method for comparing the shape changes of silicone implants using in vivo micro-CT. Mice were bilaterally implanted with silicone implants and underwent ionizing radiation to induce capsular contracture. On day 28 post-surgery mice were examined in vivo using micro-CT. The reconstructed cross-section images were visually inspected to identify distortion. Measurements were taken in 2D and 3D to quantify the shape of the implants in the normal (n = 11) and distorted (n = 5) groups. The degree of anisotropy was significantly higher in the distorted implants in the transaxial view (0.99 vs. 1.19, p = 0.002) and the y-axis lengths were significantly shorter in the sagittal (9.27 mm vs. 8.55 mm, p = 0.015) and coronal (9.24 mm vs. 8.76 mm, p = 0.031) views, indicating a deviation from the circular cross-section and shortening of the long axis. The 3D analysis revealed a significantly lower average thickness (sphere-fitting method) in distorted implants (6.86 mm vs. 5.49 mm, p = 0.002), whereas the volume and surface area did not show significant changes. Statistically significant differences between normal and distorted implants were found in 2D and 3D using distance measurements performed via micro-CT. This objective analysis method can be useful for a range of studies involving deformable implants using in vivo micro-CT. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 105B: 1447-1452, 2017.
Publisher: PeerJ
Date: 10-12-2021
DOI: 10.7717/PEERJ.12597
Abstract: The megalichthyids are one of several clades of extinct tetrapodomorph fish that lived throughout the Devonian–Permian periods. They are advanced “osteolepidid-grade” fishes that lived in freshwater sw and lake environments, with some taxa growing to very large sizes. They bear cosmine-covered bones and a large premaxillary tusk that lies lingually to a row of small teeth. Diagnosis of the family remains controversial with various authors revising it several times in recent works. There are fewer than 10 genera known globally, and only one member definitively identified from Gondwana. Cladarosymblema narrienense Fox et al. 1995 was described from the Lower Carboniferous Raymond Formation in Queensland, Australia, on the basis of several well-preserved specimens. Despite this detailed work, several aspects of its anatomy remain undescribed. Two especially well-preserved 3D fossils of Cladarosymblema narrienense , including the holotype specimen, are scanned using synchrotron or micro-computed tomography (µCT), and 3D modelled using specialist segmentation and visualisation software. New anatomical detail, in particular internal anatomy, is revealed for the first time in this taxon. A novel phylogenetic matrix, adapted from other recent work on tetrapodomorphs, is used to clarify the interrelationships of the megalichthyids and confirm the phylogenetic position of C. narrienense . Never before seen morphological details of the palate, hyoid arch, basibranchial skeleton, pectoral girdle and axial skeleton are revealed and described. Several additional features are confirmed or updated from the original description. Moreover, the first full, virtual cranial endocast of any tetrapodomorph fish is presented and described, giving insight into the early neural adaptations in this group. Phylogenetic analysis confirms the monophyly of the Megalichthyidae with seven genera included ( Askerichthys, Cladarosymblema, Ectosteorhachis, Mahalalepis, Megalichthys, Palatinichthys, and Sengoerichthys ). The position of the megalichthyids as sister group to canowindrids, crownward of “osteolepidids” (e.g., Osteolepis and Gogonasus ), but below “tristichopterids” such as Eusthenopteron is confirmed, but our findings suggest further work is required to resolve megalichthyid interrelationships.
Publisher: Springer Science and Business Media LLC
Date: 22-06-2012
DOI: 10.1007/S00198-011-1688-9
Abstract: The interrelation of calcium and phosphorus was evaluated as a function of bone material quality in femoral heads from male fragility fracture patients via surface analytical imaging as well as scanning microscopy techniques. A link between fragility fractures and increased calcium to phosphorus ratio was observed despite normal mineralization density distribution. Bone fragility in men has been recently recognized as a public health issue, but little attention has been devoted to bone material quality and the possible efficacy in fracture risk prevention. Clinical routine fracture risk estimations do not consider the quality of the mineralized matrix and the critical role played by the different chemical components that are present. This study uses a combination of different imaging and analytical techniques to gain insights into both the spatial distribution and the relationship of phosphorus and calcium in bone. X-ray photoelectron spectroscopy and time-of-flight secondary ion mass spectrometry imaging techniques were used to investigate the relationship between calcium and phosphorus in un-embedded human femoral head specimens from fragility fracture patients and non-fracture age-matched controls. The inclusion of the bone mineral density distribution via backscattered scanning electron microscopy provides information about the mineralization status between the groups. A link between fragility fracture and increased calcium and decreased phosphorus in the femoral head was observed despite normal mineralization density distribution. Results exhibited significantly increased calcium to phosphorus ratio in the fragility fracture group, whereas the non-fracture control group ratio was in agreement with the literature value of 1.66 M ratio in mature bone. Our results highlight the potential importance of the relationship between calcium and phosphorus, especially in areas of new bone formation, when estimating fracture risk of the femoral head. The determination of calcium and phosphorus fractions in bone mineral density measurements may hold the key to better fracture risk assessment as well as more targeted therapies.
Publisher: Elsevier BV
Date: 10-2013
DOI: 10.1016/J.JOCA.2013.06.020
Abstract: Bisphosphonates are considered potential disease modifying osteoarthritis (OA) agents. The present study investigated the efficacy of pre-emptive, early, and delayed alendronate (ALN) treatment initiation on subchondral trabecular bone and cartilage in low-dose monosodium iodoacetate (MIA)-induced knee OA in rats. Male rats received pre-emptive (n = 12, day 0-end of week 2), early (n = 12, end of week 2-end of week 6), or delayed (n = 12, end of week 6-end of week 10) ALN treatment (30 μg/kg/week). Pre-emptive ALN-treated rats were scanned using in vivo micro-computed tomography (micro-CT) after 2 weeks and then sacrificed, early ALN-treated rats were scanned after 2 and 6 weeks and sacrificed, and the delayed ALN-treated rats were scanned after 2, 6, and 10 weeks of OA induction and sacrificed. After sacrifice, bone histomorphometry and histology of the tibia and biomarker analyses were undertaken. Changes in hind limb weight-bearing were assessed from day -1 until day 14. MIA-induced pathological features similar to progressive human OA in the cartilage and subchondral bone. Pre-emptive ALN treatment preserved subchondral trabecular bone microarchitecture, prevented bone loss, decreased bone turnover and joint discomfort. Pre-emptive ALN treatment had moderate effects on cartilage degradation. Early and delayed ALN treatments prevented loss of trabeculae and decreased bone turnover, but had no significant effect on cartilage degradation. ALN prevented increased bone turnover and preserved the structural integrity of subchondral bone in experimental OA. The time point of treatment initiation is crucial for treating OA. Treating both the subchondral bone and cartilage in OA would be clinically more beneficial.
Publisher: MDPI AG
Date: 19-09-2022
DOI: 10.3390/MET12091548
Abstract: This study aimed to improve the overall fatigue properties of WAAM-produced SDSS by changing the interpass temperatures. Micro-computed tomography was used to quantitatively characterise the internal defects, such as porosity, in large-volume WAAM-fabricated SDSS materials. An increase in the interpass temperature led to a reduction in the ferrite phase balance by up to 20%. The fatigue anisotropy was still evident, but the fatigue limit in the weakest (transverse) direction was increased to 250 MPa or by approximately 40%. Meanwhile, the increased interpass temperature had no significant effect on fatigue resistance in the longitudinal direction. This study suggests that the interpass temperature can be critical for both achieving isotropic mechanical properties and increasing fatigue life of structural components fabricated with the WAAM method.
Publisher: Elsevier BV
Date: 09-2011
Publisher: Springer Science and Business Media LLC
Date: 07-10-2010
DOI: 10.1007/S00198-009-1082-Z
Abstract: This study monitored in vivo the effect on bone microarchitecture of initiating antiresorptive treatment with zoledronic acid in rats at 2 weeks following ovariectomy, an early phase at which major degenerative bone changes have been found to occur. The treatment still facilitated the full reversal of cancellous bone loss in rat tibia, highlighting the importance of the time point of initiation of antiresorptive treatment. Injection of zoledronic acid in rats at time of ovariectomy has been found to fully preserve tibial bone microarchitecture over time, whereas injection at 8 weeks after ovariectomy has shown partial bone recovery. This study investigated the effect on microarchitecture of initiating antiresorptive treatment in the early phase following ovariectomy, at 2 weeks, a time point at which major degenerative changes in the bone have been found to occur. Female Sprague-Dawley rats were ided into ovariectomized group, ovariectomized group treated with zoledronic acid, and sham-operated group. In vivo micro-CT scanning of rat tibiae and morphometric analysis were performed at 0, 2, 4, 8, and 12 weeks after ovariectomy, with zoledronic acid treatment beginning 2 weeks after ovariectomy. Data were first analyzed with repeated measures analysis of variance (longitudinal study design) and then without repeated measures (cross-sectional study design). The ovariectomized group demonstrated dramatic bone loss, first detected at week 2. Conversely, at week 4, the zoledronic acid-treated group returned microstructural parameters to baseline values. Remarkable increases in bone parameters were found after 6 weeks of treatment and maintained similar to sham group until the end. The longitudinal study design provided earlier detection of bone changes compared to the cross-sectional study design. Treatment with zoledronic acid as late as 2 weeks after ovariectomy still facilitates the full reversal of cancellous bone loss in the rat tibia.
Publisher: Elsevier BV
Date: 04-2017
DOI: 10.1016/J.JBIOMECH.2017.02.022
Abstract: Osteoporosis and related bone fractures are an increasing global burden in our ageing society. Areal bone mineral density assessed through dual energy X-ray absorptiometry (DEXA), the clinically accepted and most used method, is not sufficient to assess fracture risk in idually. Finite element (FE) modelling has shown improvements in prediction of fracture risk, better than aBMD from DEXA, but is not practical for widespread clinical use. The aim of this study was to develop an adaptive neural network (ANN)-based surrogate model to predict femoral neck strains and fracture loads obtained from a previously developed population-based FE model. The surrogate model performance was assessed in simulating two loading conditions: the stance phase of gait and a fall. The surrogate model successfully predicted strains estimated by FE (r
Publisher: Wiley
Date: 25-11-2020
DOI: 10.1002/JOR.24914
Abstract: This preliminary study quantified tibia cartilage thickness (Cart.Th), subchondral bone plate thickness (SBPl.Th) and subchondral trabecular bone (STB) microarchitecture in subjects with varus‐ or valgus‐ malaligned knees diagnosed with end‐stage knee osteoarthritis (OA) and compared them to controls (non‐OA). Tibial plateaus from 25 subjects with knee‐OA (undergoing knee arthroplasty) and 15 cadavers (controls) were micro‐CT scanned (17 µm/voxel). Joint alignment was classified radiographically for OA subjects (varus‐aligned n = 18, valgus‐aligned n = 7). Cart.Th, SBPl.Th, STB bone volume fraction (BV/TV) and their medial‐to‐lateral ratios were analyzed in anteromedial, anterolateral, posteromedial and posterolateral subregions. Varus‐OA and valgus‐OA were compared to controls. Compared to controls (1.19–1.54 mm), Cart.Th in varus‐OA was significantly lower anteromedially (0.58 mm, −59%) and higher laterally (2.19–2.47 mm, +60–63%) in valgus‐OA, Cart.Th was significantly higher posteromedially (1.86 mm, +56%). Control medial‐to‐lateral Cart.Th ratios were around unity (0.8–1.1), in varus‐OA significantly below (0.2–0.6) and in valgus‐OA slightly above (1.0–1.3) controls. SBPl.Th and BV/TV were significantly higher medially in varus‐OA (0.58‐0.72 mm and 37–44%, respectively) and laterally in valgus‐OA (0.60–0.61 mm and 32–37%), compared to controls (0.26–0.47 mm and 18–37%). In varus‐OA, the medial‐to‐lateral SBPl.Th and BV/TV ratios were above unity (1.4–2.4) and controls (0.8–2.1) in valgus‐OA they were closer to unity (0.8‐1.1) and below controls. Varus‐ and valgus‐OA tibia differ significantly from controls in Cart.Th, SBPl.Th and STB microarchitecture depending on joint alignment, suggesting structural changes in OA may reflect differences in medial‐to‐lateral load distribution upon the tibial plateau. Here we identified an inverse relationship between cartilage thickness and underlying subchondral bone, suggesting a whole‐joint response in OA to daily stimuli.
Publisher: Institute of Electrical and Electronics Engineers (IEEE)
Date: 10-2006
Publisher: Elsevier BV
Date: 09-2022
Publisher: Institute of Electrical and Electronics Engineers (IEEE)
Date: 06-2006
Publisher: Wiley
Date: 29-05-2015
DOI: 10.1002/JBM.A.35484
Abstract: The study aimed to determine the effects of parthenolide (PAR) on bone volume (BV) and bone surface resorption as assessed by live-animal microcomputed tomography (μCT) and possible osteocyte death as indicated by empty lacunae histologically in polyethylene (PE) particle-induced calvarial osteolysis in mice. Baseline μCT scans were conducted 7 days preimplantation of 2 × 10(8) PE particles/mL over the calvariae (day 0). PAR at 1 mg/kg/day was subcutaneously injected on days 0, 4, 7, and 10. At day 14, BV and surface resorption was analyzed with μCT. Calvarial tissue was processed for histomorphometric osteocyte evaluation. Serum was analyzed for type-1 carboxy-terminal collagen crosslinks (CTX-1) and osteoclast associated receptor (OSCAR) levels by ELISA. PE significantly decreased BV (p = 0.0368), increased surface bone resorption area (p = 0.0022), and increased the percentage of empty lacunae (p = 0.0043). Interestingly, PAR significantly reduced the resorption surface area (p = 0.0022) and the percentage of empty osteocyte lacunae (p = 0.0087) in the PE-calvariae, but it did not affect BV, serum CTX-1 or OSCAR levels. The ability of PAR to inhibit PE-induced surface bone erosion may better reflect the in vivo situation, where bone resorption occurs on the surface at the bone-implant interface and may also be related to the role of osteocytes in this pathology.
Publisher: Elsevier BV
Date: 11-2007
DOI: 10.1016/J.BONE.2007.07.014
Abstract: For normal bone, aging has been associated with a decrease of both density and failure strength, and with the development of pathologies such as osteoporosis. Conversely, it has been reported that another common disease, osteoarthritis, may alter these age-related changes in cancellous bone, suggesting that it may have a protective role against osteoporosis and the correspondent fracture risk. It was reported that in the principal compressive region of the femoral head in osteoarthritis the bone density does not depend on age. However, it is not clear if this independence on age of the cancellous bone density corresponds also to a reduced dependence on age of the strength to failure. The present work examined cancellous bone from the principal compressive region of the femoral head of 37 patients having severe osteoarthritis. The aim was (1) to investigate the dependence on age of both the structural parameters and the ultimate stress and (2) to investigate the relationships between the ultimate stress and the structural parameters. Using X-ray microcomputed tomography, three-dimensional structural parameters, such as bone volume fraction, direct trabecular thickness and structure model index were calculated. Then the specimens were compressed to failure to determine the ultimate stress. It was found that none of the investigated structural parameters did depend on age, and also the ultimate stress did not depend on age (p>0.05 for all regressions on age). In addition, the ultimate stress was significantly correlated with the structural parameters, primary with the minimum bone volume fraction and the average bone volume fraction (R(2)=0.95 and R(2)=0.84, respectively). These findings show that severe osteoarthritis or a related factor may change the age dependences of both the structural parameters and the mechanical properties usually reported for normal cancellous bone. These results suggest for this pathology to have a protective role against the age-related decrease in density, the age-related deterioration of the microarchitecture and the age-related decrease of the failure strength for the cancellous bone in the principal compressive region of the human femoral head.
Publisher: Springer International Publishing
Date: 2016
Publisher: World Scientific Pub Co Pte Lt
Date: 06-2005
DOI: 10.1142/S0219519405001473
Abstract: This work describes the preliminary results of an ongoing study, that aims to obtain relationships between the experimentally determined mechanical properties of trabecular bone of the human femoral head and the morphometric parameters evaluated by microCT. Thirteen cylindrical s les of human trabecular bone were extracted from the femoral head of thirteen patients. They were examined by microCT and then mechanically tested in compression along the main axis observable in the trabeculae. After mechanical testing, the ash density of the s les was determined. Linear relationships were found between ash density and the bone volume fraction (R 2 = 0.83), elastic modulus and bone volume fraction (R 2 = 0.72), ultimate stress and bone volume fraction (R 2 = 0.81), in agreement with what reported in literature. The described protocol will be used to investigate trabecular bone s les collected from patients with different pathologies.
Publisher: Springer Science and Business Media LLC
Date: 07-06-2015
DOI: 10.1007/S00223-015-0014-5
Abstract: Three-dimensional (3D) characterization of cortical porosity, most of which is under 100 µm in diameter, is usually confined to measurements made in 3-4 mm diameter cylinders of bone. We used micro-computed tomography (micro-CT) scanning of entire transaxial cross sections of human proximal femoral shafts (30-35 mm diameter) to quantify regional variation in porosity within the same scan. Complete, up to 10-mm-thick, transaxial slices of femoral upper shafts from 8 female cadavers were studied (n = 3 aged 29-37 years, n = 5 aged 72-90 years). Scanning was performed using high-resolution micro-CT (8.65 µm/voxel). Micro-CT volumes (10 × 10 × 5 mm) were selected via software in the anterior, medial and lateral regions. Images were segmented with voids appearing as 3D-interconnected canals. The percent void-to-tissue volume (Vo.V/TV) and the corresponding void surface area/TV were 86-309% higher in older than younger subjects in anterior (p = 0.034), medial (p = 0.077), and lateral aspects (p = 0.034). Although not significant, void separation was reciprocally lower by 19-39%, and void diameter was 65% larger in older than younger subjects void number tended to be 24-25% higher medially and laterally but not anteriorly. For all specimens combined, medially there was higher Vo.V/TV and void surface area/TV than anteriorly (+48%, p = 0.018 +33%, p = 0.018) and laterally (+56%, p = 0.062 +36%, p = 0.043). There is regional heterogeneity in the 3D microarchitecture of the intracortical canals of the femoral shaft. The higher void volume in advanced age appears to be due to larger, rather than more, pores. However, creation of new canals from existing canals may contribute, depending on the location. High-resolution micro-computed tomography scanning of entire bone segments enables quantification of the 3D microanatomy of the intracortical void network at multiple locations.
Publisher: Elsevier BV
Date: 04-2016
Publisher: Springer Science and Business Media LLC
Date: 10-11-2020
DOI: 10.1007/S00402-020-03665-3
Abstract: A characterization of the internal bone microstructure of the radial head could provide a better understanding of commonly occurring fracture patterns frequently involving the (antero)lateral quadrant, for which a clear explanation is still lacking. The aim of this study is to describe the radial head bone microstructure using micro-computed tomography (micro-CT) and to relate it to gross morphology, function and possible fracture patterns. Dry cadaveric human radii were scanned by micro-CT (17 μm ixel, isotropic). The trabecular bone microstructure was quantified on axial image stacks in four quadrants: the anterolateral (AL), posterolateral (PL), posteromedial (PM) and anteromedial (AM) quadrant. The AL and PL quadrants displayed the significantly lowest bone volume fraction and trabecular number (BV/TV range 12.3-25.1%, Tb.N range 0.73-1.16 mm Our microstructural results suggest that the lateral side is the "weaker side", exhibiting lower bone volume faction, less trabeculae and higher trabecular separation, compared to the medial side. As the forearm is pronated during most falls, the underlying bone microstructure could explain commonly observed fracture patterns of the radial head, particularly more often involving the AL quadrant. If screw fixation in radial head fractures is considered, surgeons should take advantage of the "stronger" bone microstructure of the medial side of the radial head, should the fracture line allow this.
Publisher: Wiley
Date: 02-2007
DOI: 10.1111/J.1365-2818.2007.01731.X
Abstract: X-ray microtomography permits the nondestructive investigation of trabecular and cortical bone specimens without special preparation of the s le. To do a quantitative characterization, the cross-section images have to be binarized, separating bone from nonbone. For this purpose, a widely used method is uniform thresholding. However, for commonly available microtomography scanners which use a polychromatic X-ray source, it is unclear what effect the surrounding medium (e.g. air, saline solution, polymethylmethacrylate) has on the threshold value used for the binarization. In the literature an easy procedure to find the optimal uniform threshold value for a given acquisition condition is reported. By applying this procedure, the present work investigated whether a microtomography scan of trabecular bone s les in air or embedded in polymethylmethacrylate gave the same results in terms of structural parameters. The gold standard, that is, histological sections, was used as a reference. Two fixed threshold values were found, one for the microtomography scans performed in air and one for the scans with the same s les embedded in polymethylmethacrylate. These were applied on the correspondent microtomography images for the estimation of structural parameters, such as bone volume fraction, direct trabecular thickness, direct trabecular separation and structure model index. Paired comparisons were made in bone volume fraction between histological sections and microtomography cross-sections for the same bone s les scanned first in air and then embedded in polymethylmethacrylate, by which no significant differences were found. Paired comparisons were also made in bone volume fraction, direct trabecular thickness, direct trabecular separation and structure model index for the same s les over volumes of interest of 4 x 4 x 4 mm3 between microtomography scans in air and scans with the s les embedded in polymethylmethacrylate. Neither these comparisons showed significant differences. This leads to the conclusion that structural parameters estimated by microtomography for human trabecular bone s les scanned either in air or embedded in polymethylmethacrylate are not affected by the surrounding medium (i.e. presence or absence of polymethylmethacrylate), provided that the corresponding optimal threshold value is applied for each acquisition condition.
Publisher: Wiley
Date: 20-01-2015
DOI: 10.1111/SJI.12259
Publisher: Elsevier BV
Date: 12-2014
DOI: 10.1016/J.JMBBM.2014.09.009
Abstract: For cancellous bone screws, the respective roles of the applied insertion torque (TInsert) and of the quality of the host bone (microarchitecture, areal bone mineral density (aBMD)), in contributing to the mechanical holding strength of the bone-screw construct (FPullout), are still unclear. During orthopaedic surgery screws are tightened, typically manually, until adequate compression is attained, depending on surgeons' manual feel. This corresponds to a subjective insertion torque control, and can lead to variable levels of tightening, including screw stripping. The aim of this study, performed on cancellous screws inserted in human femoral heads, was to investigate which, among the measurements of aBMD, bone microarchitecture, and the applied TInsert, has the strongest correlation with FPullout. Forty six femoral heads were obtained, over which microarchitecture and aBMD were evaluated using micro-computed tomography and dual X-ray absorptiometry. Using an automated micro-mechanical test device, a cancellous screw was inserted in the femoral heads at TInsert set to 55% to 99% of the predicted stripping torque beyond screw head contact, after which FPullout was measured. FPullout exhibited strongest correlations with TInsert (R=0.88, p<0.001), followed by structure model index (SMI, R=-0.81, p<0.001), bone volume fraction (BV/TV, R=0.73, p<0.001) and aBMD (R=0.66, p<0.01). Combinations of TInsert with microarchitectural parameters and/or aBMD did not improve the prediction of FPullout. These results indicate that, for cancellous screws, FPullout depends most strongly on the applied TInsert, followed by microarchitecture and aBMD of the host bone. In trabecular bone, screw tightening increases the holding strength of the screw-bone construct.
Publisher: MDPI AG
Date: 28-04-2021
Abstract: The Goldilocks Work Principle expresses that productive work should be redesigned to comprise physical behaviors of different intensities in a composition promoting workers’ health and fitness. This study is the first to assess the feasibility of redesigning work in an industrial setting according to the Goldilocks Work Principle. We recruited workers (n = 20) from a brewery in Denmark, and we conducted a participatory 16-week intervention including a workshop and two consultations. The workshop aimed to support the workers in modifying their work, while the consultations assisted the eventual implementation. Feasibility was evaluated as per three aspects: (1) developing modifications of work, (2) implementing these modifications, and (3) changing physical behavior and self-reported fatigue, pain and energy. The three aspects were addressed through records completed by the workers, measurements of workers’ physical behavior and intensity during ‘control’ workdays (i.e., usual work) and ‘intervention’ workdays (i.e., modified work), and self-reported fatigue, pain and energy level following both types of workday. Five modifications to work were developed, and three of these five modifications were implemented. To some extent, physical behavior and intensity changed as intended during ‘intervention’ workdays compared to ‘control’ workdays. Workers were also less fatigued, had less pain, and had more energy after ‘intervention’ workdays. These results suggest that it is feasible to develop and implement modified work based on the Goldilocks Work Principle among industrial workers. However, we also identified several barriers to the implementation of such modifications.
Publisher: Elsevier BV
Date: 02-2020
Publisher: Wiley
Date: 05-2006
DOI: 10.1111/J.1365-2818.2006.01580.X
Abstract: X-ray microtomography is rapidly gaining importance as a non-destructive investigation technique, especially in the three-dimensional examination of trabecular bone. Appropriate quantitative three-dimensional parameters describing the investigated structure were introduced, such as the model-independent thickness and the structure model index. The first parameter calculates a volume-based thickness of the structure in three dimensions independent of an assumed structure type. The second parameter estimates the characteristic form of which the structure is composed, i.e. whether it is more plate-like, rod-like or even sphere-like. These parameters are now experiencing a great diffusion and are rapidly growing in importance. To measure the accuracy of these three-dimensional parameters, a physical three-dimensional phantom containing different known geometries and thicknesses, resembling those of the examined structures, is needed. Unfortunately, such particular phantoms are not commonly available and neither does a consolidated standard exist. This work describes the realization of a calibration phantom for three-dimensional X-ray microtomography examination and reports an application ex le using an X-ray microtomography system. The calibration phantom (external size 13 mm diameter, 23 mm height) was based on various aluminium inserts embedded in a cylinder of polymethylmethacrylate. The inserts had known geometries (wires, foils, meshes and spheres) and thicknesses (ranging from 20 microm to 1 mm). The phantom was successfully applied to an X-ray microtomography device, providing imaging of the inserted structures and calculation of three-dimensional parameters such as the model-independent thickness and the structure model index. With the indications given in the present work it is possible to design a similar phantom in a histology laboratory and to adapt it to the requested applications.
Publisher: American Society of Hematology
Date: 09-07-2009
DOI: 10.1182/BLOOD-2008-12-195859
Abstract: Autosomal dominant osteogenesis imperfecta (OI) caused by glycine substitutions in type I collagen is a paradigmatic disorder for stem cell therapy. Bone marrow transplantation in OI children has produced a low engraftment rate, but surprisingly encouraging symptomatic improvements. In utero transplantation (IUT) may hold even more promise. However, systematic studies of both methods have so far been limited to a recessive mouse model. In this study, we evaluated intrauterine transplantation of adult bone marrow into heterozygous BrtlIV mice. Brtl is a knockin mouse with a classical glycine substitution in type I collagen [α1(I)-Gly349Cys], dominant trait transmission, and a phenotype resembling moderately severe and lethal OI. Adult bone marrow donor cells from enhanced green fluorescent protein (eGFP) transgenic mice engrafted in hematopoietic and nonhematopoietic tissues differentiated to trabecular and cortical bone cells and synthesized up to 20% of all type I collagen in the host bone. The transplantation eliminated the perinatal lethality of heterozygous BrtlIV mice. At 2 months of age, femora of treated Brtl mice had significant improvement in geometric parameters (P .05) versus untreated Brtl mice, and their mechanical properties attained wild-type values. Our results suggest that the engrafted cells form bone with higher efficiency than the endogenous cells, supporting IUT as a promising approach for the treatment of genetic bone diseases.
Publisher: Springer Science and Business Media LLC
Date: 2011
DOI: 10.1186/AR3543
Publisher: Elsevier BV
Date: 2014
DOI: 10.1016/J.JBIOMECH.2013.11.030
Abstract: During insertion of a cancellous bone screw, the torque level reaches a plateau, at the engagement of all the screw threads prior to the screw head contact. This plateau torque (T(Plateau)) was found to be a good predictor of the insertion failure torque (stripping) and also exhibited strong positive correlations with areal bone mineral density (aBMD) in ovine bone. However, correlations between T(Plateau) and aBMD, as well as correlations between T(Plateau) and bone microarchitecture, have never been explored in human bone. The aim of this study was to determine whether T(Plateau), a predictor of insertion failure torque, depends on aBMD and/or bone microarchitecture in human femoral heads. Fifty-two excised human femoral heads were obtained. The aBMD and microarchitecture of each specimen were evaluated using dual X-ray Absorptiometry and micro-computed tomography. A cancellous screw was inserted into specimens using an automated micro-mechanical test device, and T(Plateau) was calculated from the insertion profile. T(Plateau) exhibited the strongest correlation with the structure model index (SMI, R=-0.82, p<0.001), followed by bone volume fraction (BV/TV, R=0.80, p<0.01) and aBMD (R=0.76, p<0.01). Stepwise forward regression analysis showed an increase for the prediction of T(Plateau) when aBMD was combined with microarchitectural parameters, i.e., aBMD combined with SMI (R(2) increased from 0.58 to 0.72) and aBMD combined with BV/TV and BS/TV (R(2) increased from 0.58 to 0.74). In conclusion, T(Plateau), a strong predictor for insertion failure torque, is significantly dependent on bone microarchitecture (particularly SMI and BV/TV) and aBMD.
Publisher: Elsevier BV
Date: 08-2018
DOI: 10.1016/J.JMBBM.2018.05.016
Abstract: Time-elapsed micro-computed-tomography (μCT) imaging allows studying bone micromechanics. However, no study has yet performed time-elapsed μCT imaging of human femoral neck fractures. We developed a protocol for time-elapsed synchrotron μCT imaging of the microstructure in the entire proximal femur, while inducing clinically-relevant femoral neck fractures. Three human cadaver femora (females, age: 75-80 years) were used. The specimen-specific force to be applied at each load step was based on the specimens' strength estimated a priori using finite-element analysis of clinical CT images. A radio-transparent compressive stage was designed for loading the specimens while recording the applied load during synchrotron μCT scanning. The total μCT scanning field of view was 146 mm wide and 131 mm high, at 29.81 µm isotropic pixel size. Specimens were first scanned unloaded, then under incremental load steps, each equal to 25% of the estimated specimens' strength, and ultimately after fracture. Fracture occurred after 4-5 time-elapsed load steps, displaying sub-capital fracturing of the femoral neck, in agreement with finite-element predictions. Time-elapsed μCT images, co-registered to those of the intact specimen, displayed the proximal femur microstructure under progressive deformation up to fracture. The images showed (1) a spatially heterogeneous deformation localized in the proximal femoral head (2) a predominantly elastic recovery, after load removal, of the diaphyseal and trochanteric regions and (3) post-fracture residual displacements, mainly localized in the fractured region. The time-elapsed μCT imaging protocol developed and the high resolution images generated, made publicly available, may spur further research into human femur micromechanics and fracture.
Publisher: Springer Science and Business Media LLC
Date: 23-02-2022
DOI: 10.1186/S12889-022-12643-W
Abstract: The Goldilocks Work Principle expresses that productive work should be designed to promote workers’ health. We recently showed that it is feasible to develop and implement modifications to productive work that change physical behaviors (i.e. sitting, standing and being active) in a direction that may promote health among industrial workers. Therefore, the aim of the present study is to conduct a cluster randomised controlled trial investigating health effects of implementing the Goldilocks Work intervention among industrial workers. Our implementation plan consists of educating work teams, organizing implementation meetings, and providing feedback to workers. Three meetings with a preselected local workplace group will be scheduled. The first meeting educates the group to use a planning tool by which work can be planned to have ‘just right’ physical behaviors. The second and third meetings will focus on supporting implementation of the tool in daily work. An expected 28 clusters of work teams across two participating production sites will be randomized to either intervention or control group. Data collection will consist of 1) questionnaires regarding work and musculoskeletal health, 2) wearable sensor measurements of the physical behavior, and 3) assessment of general health indicators, including BMI, blood pressure, and fat percentage. The primary outcome is musculoskeletal health, measured by low back pain intensity, and secondary outcomes are 1) physical behaviors at work, 2) accumulated time in long bouts of sitting, standing, and being active and 3) perceived fatigue and energy during work. Furthermore, implementation and cost of the intervention will be evaluated based on questionnaires and data from the planning tool completed by the workers. This study will evaluate the effectiveness and implementation of a 12 - weeks Goldilocks Work intervention with the aim of improving musculoskeletal health among industrial workers. The cluster randomized controlled study design and the evaluation of the implementation, results and costs of the intervention will make it capable of contributing with valuable evidence of how productive work may be designed to promote industrial workers’ health. Clinical trial registration was assigned 10–09-2021 (ISRCTN80969503). 0.1186/ISRCTN80969503
Publisher: Springer Science and Business Media LLC
Date: 13-09-2012
DOI: 10.1007/S00774-011-0307-3
Abstract: Although a strong relationship exists between areal bone mineral density (aBMD) derived from dual-energy X-ray absorptiometry (DXA) and bone strength, the predictive validity of aBMD for osteoporotic vertebral fractures remains suboptimal. The diagnostic sensitivity of DXA may be improved by assessing aBMD within vertebral subregions, rather than relying on an estimate derived from the total area of the vertebra. The objective of this study was to validate a method of measuring subregional vertebral aBMD in vitro using lateral-projection DXA against subregional volumetric BMD (vBMD) measured with peripheral quantitative computed tomography (pQCT). A mixed set of 49 lumbar and thoracic vertebrae from 25 donors were scanned using lateral-projection DXA and pQCT. aBMD and apparent vBMD were measured in 7 vertebral regions (1 total area and 6 subregions) from the lateral DXA scan. vBMD was calculated in anatomically equivalent regions from pQCT scan data, using a customised software program designed to increase efficiency of the analysis process. Significant differences in densitometric parameters between subregions were observed by DXA and pQCT (P < 0.01). Subregional vBMD derived from pQCT was explained by a significant proportion of the variance in DXA-derived aBMD (R (2) = 0.51-0.67, P < 0.05) and apparent vBMD (R (2) = 0.64-0.75, P < 0.05). These results confirm the validity of measuring aBMD in vertebral subregions using lateral-projection DXA. The clinical significance should now be explored.
Publisher: Springer Science and Business Media LLC
Date: 27-02-2017
DOI: 10.1007/S00774-017-0815-X
Abstract: This study aimed at assessing the feasibility of a discrete algebraic reconstruction technique (DART) to be used in in vivo small animal bone studies. The advantage of discrete tomography is the possibility to reduce the amount of X-ray projection images, which makes scans faster and implies also a significant reduction of radiation dose, without compromising the reconstruction results. Bone studies are ideal for being performed with discrete tomography, due to the relatively small number of attenuation coefficients contained in the image [namely three: background (air), soft tissue and bone]. In this paper, a validation is made by comparing trabecular bone morphometric parameters calculated from images obtained by using DART and the commonly used standard filtered back-projection (FBP). Female rats were ided into an ovariectomized (OVX) and a sham-operated group. In vivo micro-CT scanning of the tibia was done at baseline and at 2, 4, 8 and 12 weeks after surgery. The cross-section images were reconstructed using first the full set of projection images and afterwards reducing them in number to a quarter and one-sixth (248, 62, 42 projection images, respectively). For both reconstruction methods, similar changes in morphometric parameters were observed over time: bone loss for OVX and bone growth for sham-operated rats, although for DART the actual values were systematically higher (bone volume fraction) or lower (structure model index) compared to FBP, depending on the morphometric parameter. The DART algorithm was, however, more robust when using fewer projection images, where the standard FBP reconstruction was more prone to noise, showing a significantly bigger deviation from the morphometric parameters obtained using all projection images. This study supports the use of DART as a potential alternative method to FBP in X-ray micro-CT animal studies, in particular, when the number of projections has to be drastically minimized, which directly reduces scanning time and dose.
Publisher: Elsevier BV
Date: 10-2022
DOI: 10.1016/J.JMBBM.2022.105336
Abstract: Primary stability of press-fit tibial trays is achieved by introducing an interference fit between bone and implant. The internal cancellous bone strains induced during this process and during loading have yet to be quantified experimentally. Advancements in large-gantry micro-CT imaging and digital volume correlation (DVC) allow quantification of such strains. However, before undertaking such a test, experimental requirements and DVC performance need to be examined, particularly considering the presence of a large orthopaedic implant (tibial tray). The aim of this study was to assess the DVC zero-strain accuracy (mean absolute error: MAER) and precision (standard deviation of error: SDER) on a cadaveric human tibia implanted with a titanium press-fit tray across four plausible scanning configurations, using a cabinet micro-CT system (Nikon XT H 225 ST). These varied in rotation step and resulting scanning time (106 min vs. 66 min), presence or absence of a 2 mm-thick aluminium cylinder for mechanical testing, and X-ray tube voltage (150 kVp vs. 215 kVp). One proximal tibia was implanted and micro-CT scanned (42 μm ixel), with repeated scanning and specimen repositioning in between. DVC (DaVis, LaVision, direct correlation) was performed on nine cubic volumes of interest (VOIs: 13.4 mm-side) and across the entire proximal tibia. Strain errors were comparable across the four scanning configurations and sufficiently low for assessing bone within its elastic region in VOIs (MAER=223-540 με SDER=88-261 με) and at organ level (MAER=536 με SDER=473 με). Whilst the investigated experimental conditions, including a large titanium implant, present added complexity for DVC analysis, scans of sufficient quality can be achieved, reaching a compromise between the DVC requirements and the wanted application. The approach used for choosing the X-ray source settings considering the transmitted X-ray signal intensity and source power, is also discussed.
Publisher: Wiley
Date: 17-07-2021
DOI: 10.1002/JOR.25140
Abstract: Biomechanical factors (e.g., joint loading) have a significant role in the progression of osteoarthritis (OA). However, some relationships between in vivo joint loading indices and tibial cartilage thickness are conflicting. This study investigated relationships between pre‐operative in vivo external knee joint moments, joint alignment and regional tibial cartilage thickness using micro‐CT in subjects with end‐stage knee OA. Tibial plateaus from 25 patients that underwent knee replacement for OA were micro‐CT scanned (17 µm/voxel). Prior to surgery, subjects underwent gait analysis to calculate external knee moments. The mechanical axis deviation (MAD) was obtained from pre‐operative radiographs. Cartilage thickness (Cart.Th) was analyzed from micro‐CT images, in anteromedial, anterolateral, posteromedial and posterolateral subregions of interest. Medial‐to‐lateral Cart.Th ratios were also explored. Relationships between Cart.Th and joint loading indices were examined using Pearson's correlations. Significant correlations were found between Cart.Th and joint loading indices, positive anteromedially with the first peak knee adduction moment ( r = 0.55, p 0.01) and external rotation moment (ERM r = 0.52, p 0.01), and negative with MAD ( r = −0.76, p 0.001). In the lateral regions, these correlations had opposite signs. The medial‐to‐lateral Cart.Th ratio correlated strongly with ERM ( r = 0.63, p = 0.001) and MAD ( r = −0.75, p 0.001). Joint loading indices correlated with regional cartilage thickness values and their medial‐to‐lateral ratios in end‐stage knee OA subjects, with higher regional loads corresponding to thinner cartilage. These relationships have the opposite sign compared to the subchondral bone microarchitecture found in our previous study on the same specimens, which may suggest a complementary bone–cartilage interplay in response to loading.
Publisher: Elsevier BV
Date: 04-2018
DOI: 10.1016/J.JOCD.2018.08.001
Abstract: This paper explores the effects of aging on femoral neck (FN) anatomy in a study of women aged 20-90years in relation to implications for FN fracture propensity in buckling. Five hundred and four participants were scanned by Quantitative Computed Tomography and analyzed using Quantitative Computed Tomography Pro BIT (Mindways). FN cross-section was split through geometric center into superior and inferior sectors. Bone mass, structural measurements, and bone mineral density were analyzed. Buckling ratio was calculated as ratio of buckling radius to cortical thickness. Between 2nd decade and 8th decade, age-related integral bone mass reduction in superior sector was substantially larger than in inferior sector (33% compared to 21%), especially in cortical bone superiorly compared to inferiorly (53% vs 21% p < 0.001), principally due to reduction in cortical thickness, averaged cortical thickness (56%) with little difference in density. Superior and inferior sector trabecular bone mineral density reduction was similar at 41% and 43% respectively. Differential cortical bone loss in superior sector resulted in a 59% inferior displacement (δ) of center-of-mass from geometric center. Differences in δ and averaged cortical thickness with age accounted for a 151% increase in mean superior buckling ratio from 9 to 23. Analysis confirms significant progressive age-related superior cortical bone loss as the major age effect on FN structure with relative preservation of inferior cortex probably related to maintenance of inferior sector by regular loading as a result of standing and walking. Computation of buckling ratio may allow prediction of fracture propensity in a sideways fall.
Publisher: Springer Science and Business Media LLC
Date: 09-2011
Publisher: Springer Science and Business Media LLC
Date: 26-07-2015
DOI: 10.1007/S00586-014-3455-Z
Abstract: In the literature, inter-vertebral MRI signal intensity changes (Modic changes) were associated with corresponding histological observations on endplate biopsies. However, tissue-level studies were limited. No quantitative histomorphometric study on bone biopsies has yet been conducted for Modic changes. The aim of this study was to characterise the bone micro-architectural parameters and bone remodelling indices associated with Modic changes. Forty patients suffering from disabling low back pain, undergoing elective spinal surgery, and exhibiting Modic changes on MRI (Modic 1, n = 9 Modic 2, n = 25 Modic 3, n = 6), had a transpedicular vertebral body biopsy taken of subchondral bone. Biopsies were first examined by micro-CT, for 3D morphometric analysis of bone volume fraction (BV/TV), trabecular thickness (Tb.Th), trabecular separation, trabecular number, and structure model index. Then, s les underwent histological analysis, for determination of bone remodelling indices: osteoid surface to bone surface ratio (OS/BS), eroded surface to bone surface (ES/BS) and osteoid surface to eroded surface ratio (OS/ES). Micro-CT analysis revealed significantly higher BV/TV (up to 70% increase, p < 0.01) and Tb.Th (up to +57%, p < 0.01) in Modic 3 biopsies, compared to Modic 1 and 2. Histological analysis showed significantly lower OS/BS in Modic 2 biopsies (more than 28% decrease, p < 0.05) compared to 1 and 3. ES/BS progressively decreased from Modic 1 to 2 to 3, whereas OS/ES progressively increased with significantly higher values in Modic 3 (up to 159% increase, p < 0.05) than in Modic 1 and 2. Significant differences were found in bone micro-architectural parameters and remodelling indices among Modic types. Modic 1 biopsies had evidence of highest bone turnover, possibly due to an inflammatory process Modic 2 biopsies were consistent with a reduced bone formation/remodelling stage Modic 3 biopsies suggested a more stable sclerotic phase, with significantly increased BV/TV and Tb.Th compared to Modic 1 and 2, linked to increased bone formation and reduced resorption.
Publisher: Hindawi Limited
Date: 04-03-2020
DOI: 10.1155/2020/6245798
Abstract: Rheumatoid arthritis is characterised by a chronic inflammatory response resulting in destruction of the joint and significant pain. Although a range of treatments are available to control disease activity in RA, bone destruction and joint pain exist despite suppression of inflammation. This study is aimed at assessing the effects of parthenolide (PAR) on paw inflammation, bone destruction, and pain-like behaviour in a mild collagen antibody-induced arthritis (CAIA) mouse model. CAIA was induced in BALB/c mice and treated daily with 1 mg/kg or 4 mg/kg PAR. Clinical paw inflammation was scored daily, and mechanical hypersensitivity was assessed on alternate days. At end point, bone volume and swelling in the paws were assessed using micro-CT. Paw tissue sections were assessed for inflammation and pre-/osteoclast-like cells. The lumbar spinal cord and the periaqueductal grey (PAG) and rostral ventromedulla (RVM) regions of the brain were stained for glial fibrillary acidic protein (GFAP) and ionised calcium-binding adaptor molecule 1 (IBA1) to assess for glial reactivity. Paw scores increased in CAIA mice from days 5-10 and were reduced with 1 mg/kg and 4 mg/kg PAR on days 8-10. Osteoclast-like cells on the bone surface of the radiocarpal joint and within the soft tissue of the hind paw were significantly lower following PAR treatment ( p 0.005 ). GFAP- and IBA1-positive cells in the PAG and RVM were significantly lower following treatment with 1 mg/kg ( p 0.0001 and p = 0.0004 , respectively) and 4 mg/kg PAR ( p 0.0001 and p = 0.001 , respectively). In the lumbar spinal cord, IBA1-positive cells were significantly lower in CAIA mice treated with 4 mg/kg PAR ( p = 0.001 ). The findings indicate a suppressive effect of both low- and moderate-dose PAR on paw inflammation, osteoclast presence, and glial cell reactivity in a mild CAIA mouse model.
Publisher: Wiley
Date: 13-07-2018
DOI: 10.1002/JOR.24057
Abstract: We investigated if time between injury and surgery affects cancellous bone properties in patients suffering tibial plateau fractures (TPF), in terms of structural integrity and gene expression controlling bone loss. A cohort of 29 TPF, operated 1–17 days post‐injury, had biopsies from the fracture and an equivalent contralateral limb site, at surgery. S les were assessed using micro‐computed tomography and real‐time RT‐PCR analysis for the expression of genes known to be involved in bone remodeling and fracture healing. Significant decreases in the injured vs control side were observed for bone volume fraction (BV/TV, −13.5 ± 6.0%, p = 0.011), trabecular number (Tb.N, −10.5 ± 5.9%, p = 0.041) and trabecular thickness (Tb.Th, −4.6 ± 2.5%, p = 0.033). Changes in these parameters were more evident in patients operated 5–17 days post‐injury, compared to those operated in the first 4 days post‐injury. A significant negative association was found between Tb.Th ( r = −0.54, p 0.01) and BV/TV ( r = −0.39, p 0.05) in relation to time post‐injury in the injured limb. Both BV/TV and Tb.Th were negatively associated with expression of key molecular markers of bone resorption, CTSK , ACP5 , and the ratio of RANKL : OPG mRNA. These structure/gene expression relationships did not exist in the contralateral tibial plateau of these patients. This study demonstrated that there is a significant early time‐dependent bone loss in the proximal tibia after TPF. This bone loss was significantly associated with altered expression of genes typically involved in the process of osteoclastic bone resorption but possibly also bone resorption by osteocytes. The mechanism of early bone loss in such fractures should be a subject of further investigation. © 2018 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 36:2865–2875, 2018.
Publisher: Elsevier BV
Date: 04-2010
DOI: 10.1016/J.JOCD.2010.01.120
Abstract: In the clinical environment dual-energy X-ray absorptiometry (DXA) is the current tool of first choice for assessing and monitoring skeletal integrity. A major drawback of standard DXA is that the bone mineral density (BMD) data cannot be used with certainty to predict who will sustain a vertebral fracture. However, measurement of BMD within vertebral subregions, instead of relying on a gross estimate of vertebral BMD, may improve diagnostic sensitivity. The aim of this article was to describe a validation study for subregional BMD measurement using lateral-projection DXA and to present preliminary data. Concurrent validity of measuring subregional BMD with DXA was established against measures of volumetric subregional BMD from peripheral quantitative computed tomography (pQCT) and subregional bone volume fraction from microCT at the L2 vertebral body in 8 cadaver spine specimens. The novel approaches for measuring subregional parameters with each imaging modality are described. Significant differences in bone parameters between vertebral subregions were observed for each imaging modality (p<0.05). Correspondence ranged from R(2)=0.01-0.79 and R(2)=0.06-0.80 between "DXA vs. pQCT" and "DXA vs. micro-CT," respectively. For both imaging modalities, correspondence with DXA was high for centrally and anteriorly positioned subregions. These data provide a basis for larger studies to examine the biological significance of heterogeneity in vertebral BMD.
Publisher: Elsevier BV
Date: 2007
DOI: 10.1016/J.JBIOMECH.2006.11.020
Abstract: The aim of this study was to verify whether a misalignment between the testing direction and the trabecular main direction has a significant effect on the compressive behaviour of cancellous bone. Ten cylindrical specimens were extracted from femoral heads with a misalignment to the trabecular main direction of approximately 20 degrees. Each specimen was paired with a specimen extracted aligned with the main direction of the trabeculae on the basis of the closest bone volume fraction, obtaining two groups, one 'aligned' and one 'misaligned'. The average off-axis angle was 6.1 degrees and 21.6 degrees for the 'aligned' and 'misaligned' group, respectively. The specimens underwent micro-tomographic analysis, compressive testing, micro-indentation testing and ashing. No significant differences were found in histomorphometric parameters, hardness and ash density between the two groups, whereas significant differences were found in Young's modulus and ultimate stress: both parameters, measured for the 'misaligned' group, were about 40% lower than those measured for the 'aligned' group. These results demonstrate a great effect of the angle between the testing direction and the main direction of the trabecular structure on the compressive behaviour of cancellous bone. This angle should be reduced as much as possible (in the present work the average value was 6.6+/-3.3 degrees), in any case measured, and always reported together with the mechanical parameters of cancellous bone.
Publisher: Springer Science and Business Media LLC
Date: 09-07-2013
Publisher: Hindawi Limited
Date: 2015
DOI: 10.1155/2015/564042
Abstract: Objective . To investigate the effect of Embelin, an inhibitor of X-Linked Inhibitor of Apoptosis Protein (XIAP), on inflammation and bone erosion in a collagen antibody induced arthritis (CAIA) in mice. Methods . Four groups of mice ( n = 6 per group) were allocated: CAIA untreated mice, CAIA treated with Prednisolone (10 mg/kg/day), CAIA treated with low dose Embelin (30 mg/kg/day), and CAIA treated with high dose Embelin (50 mg/kg/day). Joint inflammation was evaluated using clinical paw score and histological assessments. Bone erosion was assessed using micro-CT, tartrate resistant acid phosphatase (TRAP) staining, and serum carboxy-terminal collagen crosslinks (CTX-1) ELISA. Immunohistochemistry was used to detect XIAP protein. TUNEL was performed to identify apoptotic cells. Results . Low dose, but not high dose Embelin, suppressed inflammation as reflected by lower paw scores ( P 0.05 ) and lower histological scores for inflammation. Low dose Embelin reduced serum CTX-1 ( P 0.05 ) and demonstrated lower histological score and TRAP counting, and slightly higher bone volume as compared to CAIA untreated mice. XIAP expression was not reduced but TUNEL positive cells were more abundant in Embelin treated CAIA mice. Conclusion . Low dose Embelin suppressed inflammation and serum CTX-1 in CAIA mice, indicating a potential use for Embelin to treat pathological bone loss.
Publisher: Elsevier BV
Date: 10-2017
DOI: 10.1016/J.JOCA.2017.06.001
Abstract: To (1) stratify patient subgroups according to their distinct walking gait patterns in end-stage knee osteoarthritis (OA) (2) compare measures of joint loading and proximal tibia subchondral trabecular bone (STB) microarchitecture among these gait subgroups. Twenty-five knee OA patients undergoing total knee arthroplasty (TKA) had pre-operative gait analysis. Following surgery, excised tibial plateaus were micro-CT-scanned and STB microarchitecture analysed in four tibial condylar regions of interest. Peak knee moments were input to k-means cluster analysis, to identify subgroups with homogeneous gait patterns. Joint loading and STB microarchitecture parameters were compared among gait subgroups (Kruskal-Wallis, Bonferroni-corrected Mann-Whitney U tests). Three gait subgroups were revealed: biphasics (n = 7), flexors (n = 9), counter-rotators (n = 9). Peak knee adduction moment (KAM) and KAM impulse were significantly higher (P < 0.05) in biphasics than in flexors and counter-rotators (KAM = -0.65, -0.40 and -0.21 Nm/kg, respectively), suggesting a higher medial-to-lateral tibiofemoral load ratio in biphasics. Interestingly, STB medial-to-lateral bone volume fraction (BV/TV) ratio was also significantly higher (more than double) in biphasics and flexors than in counter-rotators (2.24, 2.00 and 1.00, respectively), whereas in biphasics it was only 10% higher than in flexors and not significantly so. Within the confines of the limited s le size, data suggests that different mechanisms between the biphasic and flexor gait subroups may generate comparable loads upon the tibial plateau and corresponding bony responses, despite significantly lower KAM indices in flexors. Hence, in flexor gait OA patients, conservative treatments designed to reduce KAM, may not be appropriate. Understanding joint loading among walking gait patterns and relationships to bone microarchitecture may aid at identifying/improving management of persons at risk for developing knee OA.
Publisher: Elsevier BV
Date: 06-2012
DOI: 10.1016/J.BONE.2012.03.002
Abstract: Significant relationships exist between areal bone mineral density (BMD) derived from dual energy X-ray absorptiometry (DXA) and bone strength. However, the predictive validity of BMD for osteoporotic vertebral fractures remains suboptimal. The diagnostic sensitivity of DXA in the lumbar spine may be improved by assessing BMD from lateral-projection scans, as these might better approximate the objective of measuring the trabecular-rich bone in the vertebral body, compared to the commonly-used posterior-anterior (PA) projections. Nowadays, X-ray micro-computed tomography (μCT) allows non-destructive three-dimensional structural characterization of entire bone segments at high resolution. In this study, human lumbar cadaver spines were examined ex situ by DXA in lateral and PA projections, as well as by μCT, with the aims (1) to investigate the ability of bone quantity measurements obtained by DXA in the lateral projection and in the PA projection, to predict variations in bone quantity measurements obtained by μCT, and (2) to assess their respective capabilities to predict whole vertebral body strength, determined experimentally. Human cadaver spines were scanned by DXA in PA projections and lateral projections. Bone mineral content (BMC) and BMD for L2 and L3 vertebrae were determined. The L2 and L3 vertebrae were then dissected and entirely scanned by μCT. Total bone volume (BV(tot)=cortical+trabecular), trabecular bone volume (BV), and trabecular bone volume fraction (BV/TV) were calculated over the entire vertebrae. The vertebral bodies were then mechanically tested to failure in compression, to determine ultimate load. The variables BV(tot), BV, and BV/TV measured by μCT were better predicted by BMC and BMD measured by lateral-projection DXA, with higher R(2) values and smaller standard errors of the estimate (R(2)=0.65-0.90, SEE=11%-18%), compared to PA-projection DXA (R(2)=0.33-0.53, SEE=22%-34%). The best predictors of ultimate load were BV(tot) and BV assessed by μCT (R(2)=0.88 and R(2)=0.81, respectively), and BMC and BMD from lateral-projection DXA (R(2)=0.82 and R(2)=0.70, respectively). Conversely, BMC and BMD from PA-projection DXA were lower predictors of ultimate load (R(2)=0.49 and R(2)=0.37, respectively). This ex vivo study highlights greater capabilities of lateral-projection DXA to predict variations in vertebral body bone quantity as measured by μCT, and to predict vertebral strength as assessed experimentally, compared to PA-projection DXA. This provides basis for further exploring the clinical application of lateral-projection DXA analysis.
Publisher: MDPI AG
Date: 27-11-2021
Abstract: Childcare workers are reported to have poor cardiorespiratory fitness and health. The Goldilocks Work Principle argues that productive work should be designed with the right composition, intensity and alternations of physical behaviors so that workers get fit and healthy. The purpose of this study was to investigate: (1) composition, (2) intensity and (3) alternations of physical behaviors during work and leisure among childcare workers. Data were collected using accelerometers and heart rate monitors over five workdays among 51 childcare workers at five Danish childcare institutions. Workers mainly spent their work time sedentary (43.0%), spent little time (0.7%) at sufficiently high cardiometabolic intensity to increase cardiorespiratory fitness and often alternated between physical behaviors (67.0% occurred in bouts of min). These findings indicate that the workers have a composition of behaviors at work dominated by sedentary time, little time with high cardiometabolic intensity, and frequent alternations between behaviors. During leisure, workers spent more time sedentary (59.4%), more time at high cardiometabolic intensity (3.4%) and less time occurred in bouts min (38.7%). We see a potential for promoting cardiorespiratory fitness and health of childcare workers by redesigning the way they play with the children, so that work time with high cardiometabolic intensity is increased.
Publisher: Springer Science and Business Media LLC
Date: 25-05-2014
DOI: 10.1007/S00223-014-9866-3
Abstract: Measurement of areal bone mineral density (aBMD) in intravertebral subregions may increase the diagnostic sensitivity of dual-energy X-ray absorptiometry (DXA)-derived parameters for vertebral fragility. This study investigated whether DXA-derived bone parameters in vertebral subregions were better predictors of vertebral bone strength in specimens with low aBMD, compared to those with higher aBMD. Twenty-five lumbar vertebrae (15 embalmed and 10 fresh-frozen) were scanned with posteroanterior- (PA) and lateral-projection DXA, and then mechanically tested in compression to ultimate failure. Whole-vertebral aBMD and bone mineral content (BMC) were measured from the PA- and lateral-projection scans and within 6 intravertebral subregions. Multivariate regression was used to predict ultimate failure load by BMC, adjusted for vertebral size and specimen fixation status across the whole specimen set, and when subgrouped into specimens with low aBMD and high aBMD. Adjusted BMC explained a substantial proportion of variance in ultimate vertebral load, when measured over the whole vertebral area in lateral projection (adjusted R (2) 0.84) and across the six subregions (ROIs 2-7) (adjusted R (2) range 0.58-0.78). The association between adjusted BMC, either measured subregionally or across the whole vertebral area, and vertebral failure load, was increased for the subgroup of specimens with identified 'low aBMD', compared to those with 'high aBMD', particularly in the anterior subregion where the adjusted R (2) differed by 0.44. The relative contribution of BMC measured in vertebral subregions to ultimate failure load is greater among specimens with lower aBMD, compared to those with higher aBMD, particularly in the anterior subregion of the vertebral body.
Start Date: 09-2019
End Date: 07-2025
Amount: $4,000,000.00
Funder: Australian Research Council
View Funded ActivityStart Date: 09-2018
End Date: 09-2019
Amount: $557,389.00
Funder: Australian Research Council
View Funded Activity