ORCID Profile
0000-0002-8935-8070
Current Organisation
KTH Royal Institute of Technology
Does something not look right? The information on this page has been harvested from data sources that may not be up to date. We continue to work with information providers to improve coverage and quality. To report an issue, use the Feedback Form.
Publisher: American Chemical Society (ACS)
Date: 21-12-2010
DOI: 10.1021/LA103001S
Abstract: The atomic force microscope fiber probe is used to directly measure the forces and friction between two human hairs under various conditions. It is shown that the forces between the hair fibers in solution can be well explained by a DLVO interaction and that cationic surfactant modifies the interactions in a manner entirely consistent with current views of adsorption behavior. A Coulombic attraction occurs between the crossed hair fibers in air due to the heterogeneity of the surface, and at shorter separations a clear dispersion interaction is observed. Exposure of the hair to a bleaching solution leads to the removal of the adhesion and solely a double-layer interaction. Two crossed hair fibers obey Amontons' classic law of friction, with a linear relation between applied load and frictional force, allowing the determination of a friction coefficient positively charged surfactant adsorption is shown to reduce the friction coefficient between the fibers in a manner consistent with boundary lubrication by a palisade layer.
Publisher: Royal Society of Chemistry (RSC)
Date: 2016
DOI: 10.1039/C5CP05837F
Abstract: Atomic force microscopy has been used to study the effect of temperature on normal forces and friction for the room temperature ionic liquid (IL) ethylammonium nitrate (EAN), confined between mica and a silica colloid probe at 25 °C, 50 °C, and 80 °C.
Publisher: Royal Society of Chemistry (RSC)
Date: 2021
DOI: 10.1039/D0NR06621D
Abstract: Self-assembly of insoluble surfactants imposes curvature restrictions on the air–water interface which leads to 3D nanopatterns that can be deposited onto solid surfaces.
Publisher: American Chemical Society (ACS)
Date: 04-10-2019
DOI: 10.26434/CHEMRXIV.9929684.V1
Abstract: A simple, insoluble monolayer of fatty acid is shown to induce 3D nanotexturing of the water–air interface. This advance has been achieved through the study of monolayers of a methyl-branched long chain fatty acid, analogous to those found on the surface of hair and wool, directly at the water–air interface. Specular neutron reflectometry combined with AFM probing of deposited monolayers shows pronounced 3D surface domains, which are absent for unbranched analogues and which are attributed to hydrocarbon packing constraints. The resulting surface topographies of the water far exceed the height perturbation that can be explained by the presence of capillary waves of a free liquid surface. These have hitherto been considered the only source of perturbation of the flatness of a planar water interface under gravity in the absence of topographical features from the presence of extended, globular or particulate matter. This amounts to a paradigm shift in the study of interfacial films and opens the possibility of 3D texturing of the water–air interface.
Publisher: Elsevier BV
Date: 11-2005
DOI: 10.1016/J.JCIS.2005.05.040
Abstract: In the pulping step of the de-inking process, the ink detaches from the fibers due to shear and physical chemical interaction. In order to get a better understanding of the forces involved between cellulose and ink, the atomic force microscope and the colloidal probe technique have been used in the presence of a model chemical dispersant (hexa-ethyleneglycol mono n-dodecyl ether, C12E6). A cellulose bead was used as the colloidal probe and three different lower surfaces have been used, an alkyd resin, mica and a cellulose sphere. The normal and lateral forces have been measured at a range of nonionic concentrations. It was found that the lateral sliding friction forces deceased with increasing surfactant concentration for both the alkyd resin and mica while no differences were observed for the cellulose surface. In addition, only a very small change in normal force could be detected for the alkyd surface as the concentration changed.
Publisher: American Physical Society (APS)
Date: 10-10-2012
Publisher: Elsevier BV
Date: 12-2000
DOI: 10.1016/S0927-7765(00)00147-8
Abstract: A non-destructive technique is presented for verifying torsional spring constants used in lateral force microscopy. Various calibrations of the microscope are required and these are detailed. The technique produces reasonable values which tend to be larger than those predicted from considerations of the cantilever dimensions. The differences are discussed in terms of length corrections and particularly the uncertainty in the thickness of the cantilevers, which has an enormous effect on the values obtained through a priori calculations. Methods for inferring the thickness are discussed. Further, artefacts in conventional force measurements related to the experiments performed here are discussed.
Publisher: AIP Publishing
Date: 11-1998
DOI: 10.1063/1.1149190
Abstract: Theoretical calculations and experimental measurements are used to show that hitherto neglected inertial effects can be significant in computer-controlled surface force measurement devices such as the atomic force microscope. The problem is analyzed in detail for the case of the van der Waals attraction in air. It is demonstrated that equating the cantilever deflection to the surface force systematically underestimates the magnitude of the surface force, increasingly so as the speed of approach is increased. It is also shown that the surface separation becomes lost at high accelerations due to a dynamic uncoupling of the cantilever deflection and angle. The effects of elastic deformation of the bodies are taken into account, including the collision-induced elastic vibrations in the solids. Experimental data are obtained for the van der Waals attraction and collision of glass surfaces in air using the measurement and analysis of surface forces device. All of the effects found in the theoretical calculations are identified in the experimental data.
Publisher: Wiley
Date: 28-06-2008
DOI: 10.1111/J.1742-4658.2008.06483.X
Abstract: The aquatic sex pheromone splendipherin (GLVSSIGKALGGLLADVVKSKGQPA-OH) of the male green tree frog Litoria splendida moves across the surface of water to reach the female. Surface pressure and X-ray reflectometry measurements confirm that splendipherin is a surface-active molecule, and are consistent with it having an ordered structure, whereby the hydrophilic portion of the peptide interacts with the underlying water and the hydrophobic region is adjacent to the vapour phase. The movement of splendipherin over the surface of water is caused by a surface pressure gradient. In order to better define the structure of splendipherin at the water/air interface we used 2D NMR studies of the pheromone with the solvent system trifluoroethanol/water (1 : 1 v/v). In this solvent system, splendipherin adopts a bent alpha helix from residues V3 to K21. The bending of the helix occurs in the centre of the peptide in the vicinity of G11 and G12. The region of splendipherin from V3 to G11 has well-defined hipathicity, whereas the hipathicity from G12 to A25 is reduced by K19 and P24 intruding into the hydrophobic and hydrophilic regions respectively. A helical structure is consistent with X-ray reflectometry data.
Publisher: Royal Society of Chemistry (RSC)
Date: 2012
DOI: 10.1039/C1CP23134K
Abstract: Colloid probe atomic force microscopy has been used to study the nanotribological properties of the silica-ethylammonium nitrate (EAN)-mica system. Normal force curve measurements reveal a series of steps at separations that are consistent with the size of an EAN ion pair (0.5 nm) due to displacement of structured solvent layers as the two surfaces are brought together. At closest separations, two steps are measured with widths of 0.3 nm and 0.1 nm, which are too small to be due to an ion pair layer. The 0.3 nm step is attributed to a partial displacement of a silica-bound cation-rich layer, with residual cations being removed in the subsequent 0.1 nm step. Lateral force measurements reveal that the frictional response is dependent on the number of ion pair layers between the surfaces. At low forces, when there is more than a single layer of EAN between silica and mica, the lateral force increases relatively steeply with applied load, and is independent of the sliding speed. At intermediate forces, a single layer of cations in an intercalated bilayer structure is present between the surfaces. The friction coefficient (μ) increases logarithmically with sliding speed consistent with an activated, discontinuous sliding process. At high force, μ is small and once again, independent of sliding velocity. The adsorbed cation layer is bound primarily to mica and compressed by the high normal force. This robust layering with a well-defined sliding plane permits the colloid probe to slide easily over the mica surface.
Publisher: American Chemical Society (ACS)
Date: 1992
DOI: 10.1021/LA00037A033
Publisher: Royal Society of Chemistry (RSC)
Date: 2014
DOI: 10.1039/C4CC00979G
Abstract: Atomic force microscopy measurements reveal that superlubricity can be "switched" on and off in situ when an ionic liquid is used to lubricate the silica-graphite interface. Applying a potential to the graphite surface changes the ion composition of the boundary layer and thus the lubricity. At positive potentials, when the interfacial ion layer is anion rich, friction falls to ultra-low levels.
Publisher: Springer Science and Business Media LLC
Date: 21-06-2013
Publisher: American Chemical Society (ACS)
Date: 28-07-2010
DOI: 10.1021/LA102189Z
Abstract: Vibrational sum frequency spectroscopy (VSFS) has been used to determine the stability toward oxidation in air of a series of unsaturated fatty acids, measuring as a function of time the changes in the chemical structure and conformational order of films spread on a Langmuir trough. The fatty acids studied consisted of a 20-carbon backbone with increasing numbers of cis double bonds in the chain: 11c-eicosenoic acid (20:1 EA, omega-9), 11c,14c-eicosadienoic acid (20:2 EA, omega-6), and 11c,14c,17c-eicosatrienoic acid (20:3 EA, omega-3). Measurements at constant surface pressure show that double bonds are lost from the surface region and that drops in intensity of the vinyl CH stretch are detectable within a few minutes of spreading the monolayer. The results are consistent with the fatty acid peroxidation free radical mechanism. The sum frequency spectra also reveal that what remains on the surface is conformationally more disordered with a larger number of gauche defects. The oxidation kinetics are found to be strongly dependent on the packing density of the monolayer, being more stable at higher pressures. Oxidation can be avoided by purging the system in an inert atmosphere. Finally, the molecular structure upon compression was tracked in unoxidized monolayers. The results suggest that the packing and orientation of the double bond sections of all three unsaturated fatty acids show remarkable similarities, with the direction of the double bonds approximately parallel to each other irrespective of the number of unsaturations in the chain, with the 20:3 EA probably forming "iron-angle" structures. The possibility of unsaturated chains in a "hairpin" configuration is discarded for area per molecules smaller than approximately 50 A(2), which corresponds to the lowest surface pressure measured with VSFS.
Publisher: AIP Publishing
Date: 2006
DOI: 10.1063/1.2162429
Publisher: Informa UK Limited
Date: 2002
Publisher: AIP Publishing
Date: 09-2007
DOI: 10.1063/1.2779215
Abstract: A number of atomic force microscopy cantilevers have been exhaustively calibrated by a number of techniques to obtain both normal and frictional force constants to evaluate the relative accuracy of the different methods. These were of either direct or indirect character—the latter relies on cantilever resonant frequencies. The so-called Sader [Rev. Sci. Instrum. 70, 3967 (1999)] and Cleveland [Rev. Sci. Instrum. 64, 403 (1993)] techniques are compared for the normal force constant calibration and while agreement was good, a systematic difference was observed. For the torsional force constants, all the techniques displayed a certain scatter but the agreement was highly encouraging. By far the simplest technique is that of Sader, and it is suggested in view of this validation that this method should be generally adopted. The issue of the photodetector calibration is also addressed since this is necessary to obtain the cantilever twist from which the torsional force is calculated. Here a technique of obtaining the torsional photodetector sensitivity by combining the direct and indirect methods is proposed. Direct calibration measurements were conducted in liquid as well as air, and a conversion factor was obtained showing that quantitative friction measurements in liquid are equally feasible provided the correct calibration is performed.
Publisher: Informa UK Limited
Date: 2005
Publisher: Springer Science and Business Media LLC
Date: 28-01-2007
Publisher: Royal Society of Chemistry (RSC)
Date: 2020
DOI: 10.1039/C9NH00722A
Abstract: The air–water interface can be textured according to the same self-assembly packing criteria that determine the wealth of 3D structures found in micellar and other hiphilic meso-phases.
Publisher: Elsevier BV
Date: 12-2014
Publisher: American Chemical Society (ACS)
Date: 10-03-2014
DOI: 10.1021/LA4042474
Abstract: Self-assembled octadecyltrichlorosilane ((OTS), CH3(CH2)17SiCl3) layers on hydroxyl-terminated silicon oxide (SiO2) were prepared. The monolayers were characterized with atomic force microscopy (AFM) and contact angle measurements their conformation was studied before, during, and after contact with a polymer (either PDMS or PTFE) surface using the vibrational sum frequency spectroscopy (VSFS) technique. During contact, the effect of pressure was studied for both polymer surfaces, but in the case of PTFE, the effect of shear rate on the contact was simultaneously studied. The VSFS response of the monolayers with pressure was almost entirely due to changes in the real area of contact with the polymer and therefore the Fresnel factors, whereas sliding caused disorder in the previously all-trans monolayer, as evidenced by a significant increase in the population of gauche defects.
Publisher: Elsevier BV
Date: 05-1996
Publisher: Elsevier BV
Date: 04-2011
DOI: 10.1016/J.BBAMEM.2010.12.020
Abstract: A pronounced membrane selectivity is demonstrated for short, hydrophilic, and highly charged antimicrobial peptides, end-tagged with aromatic amino acid stretches. The mechanisms underlying this were investigated by a method combination of fluorescence and CD spectroscopy, ellipsometry, and Langmuir balance measurements, as well as with functional assays on cell toxicity and antimicrobial effects. End-tagging with oligotryptophan promotes peptide-induced lysis of phospholipid liposomes, as well as membrane rupture and killing of bacteria and fungi. This antimicrobial potency is accompanied by limited toxicity for human epithelial cells and low hemolysis. The functional selectivity displayed correlates to a pronounced selectivity of such peptides for anionic lipid membranes, combined with a markedly reduced membrane activity in the presence of cholesterol. As exemplified for GRR10W4N (GRRPRPRPRPWWWW-NH(2)), potent liposome rupture occurs for anionic lipid systems (dioleoylphosphatidylethanolamine (DOPE)/dioleoylphosphatidylglycerol (DOPG) and Escherichia coli lipid extract) while that of zwitterionic dioleoylphosphatidylcholine (DOPC)/cholesterol is largely absent under the conditions investigated. This pronounced membrane selectivity is due to both a lower peptide binding to the zwitterionic membranes (z≈-8-10mV) than to the anionic ones (z≈-35-40mV), and a lower degree of membrane incorporation in the zwitterionic membranes, particularly in the presence of cholesterol. Replacing cholesterol with ergosterol, thus mimicking fungal membranes, results in an increased sensitivity for peptide-induced lysis, in analogy to the antifungal properties of such peptides. Finally, the generality of the high membrane selectivity for other peptides of this type is demonstrated.
Publisher: American Vacuum Society
Date: 03-2023
DOI: 10.1116/6.0002502
Abstract: Interactions between molecules in the synovial fluid and the cartilage surface may play a vital role in the formation of adsorbed films that contribute to the low friction of cartilage boundary lubrication. Osteoarthritis (OA) is the most common degenerative joint disease. Previous studies have shown that in OA-diseased joints, hyaluronan (HA) not only breaks down resulting in a much lower molecular weight (MW), but also its concentration is reduced ten times. Here, we have investigated the structural changes of lipid-HA complexes as a function of HA concentration and MW to simulate the physiologically relevant conditions that exist in healthy and diseased joints. Small angle neutron scattering and dynamic light scattering were used to determine the structure of HA-lipid vesicles in bulk solution, while a combination of atomic force microscopy and quartz crystal microbalance was applied to study their assembly on a gold surface. We infer a significant influence of both MW and HA concentrations on the structure of HA-lipid complexes in bulk and assembled on a gold surface. Our results suggest that low MW HA cannot form an amorphous layer on the gold surface, which is expected to negatively impact the mechanical integrity and longevity of the boundary layer and could contribute to the increased wear of the cartilage that has been reported in joints diseased with OA.
Publisher: Royal Society of Chemistry (RSC)
Date: 2015
DOI: 10.1039/C5NR03965G
Abstract: Electrochemical quartz crystal microbalance has been used to measure changes in the composition of the capacitive electrical double layer for 1-ethyl-3-methylimidazolium tris(pentafluoroethyl)-trifluorophosphate, an ionic liquid, in contact with a gold electrode surface as a function of potential.
Publisher: AIP Publishing
Date: 15-07-2005
DOI: 10.1063/1.1954747
Abstract: Silica is a very interesting system that has been thoroughly studied in the last decades. One of the most outstanding characteristics of silica suspensions is their stability in solutions at high salt concentrations. In addition to that, measurements of direct-interaction forces between silica surfaces, obtained by different authors by means of surface force apparatus or atomic force microscope (AFM), reveal the existence of a strong repulsive interaction at short distances (below 2nm) that decays exponentially. These results cannot be explained in terms of the classical Derjaguin, Landau, Verwey, and Overbeek (DLVO) theory, which only considers two types of forces: the electrical double-layer repulsion and the London–van der Waals attraction. Although there is a controversy about the origin of the short-range repulsive force, the existence of a structured layer of water molecules at the silica surface is the most accepted explanation for it. The overlap of structured water layers of different surfaces leads to repulsive forces, which are known as hydration forces. This assumption is based on the very hydrophilic nature of silica. Different theories have been developed in order to reproduce the exponentially decaying behavior (as a function of the separation distance) of the hydration forces. Different mechanisms for the formation of the structured water layer around the silica surfaces are considered by each theory. By the aid of an AFM and the colloid probe technique, the interaction forces between silica surfaces have been measured directly at different pH values and salt concentrations. The results confirm the presence of the short-range repulsion at any experimental condition (even at high salt concentration). A comparison between the experimental data and theoretical fits obtained from different theories has been performed in order to elucidate the nature of this non-DLVO repulsive force.
Publisher: Walter de Gruyter GmbH
Date: 2005
Abstract: The atomic force microscope (AFM) is designed to provide high-resolution (in the ideal case, atomic) topographical analysis, applicable to both conducting and nonconducting surfaces. The basic imaging principle is very simple: a s le attached to a piezoelectric positioner is rastered beneath a sharp tip attached to a sensitive cantilever spring. Undulations in the surface lead to deflection of the spring, which is monitored optically. Usually, a feedback loop is employed, which holds the spring deflection constant, and the corresponding movement of the piezoelectric positioner thus generates the image. From this it can be seen that the scanning AFM has all the attributes necessary for the determination of surface and adhesion forces a sensitive spring to determine the force , a piezoelectric crystal to alter the separation of the tip and surface, which if sufficiently well-calibrated also allows the relative separation of the tip and surface to be calculated. One can routinely quantify both the net surface force (and its separation dependence) as the probe approaches the s le, and any adhesion (pull-off) force on retraction . Interactions in relevant or practical systems may be studied, and, in such cases, a distinct advantage of the AFM technique is that a particle of interest can be attached to the end of the cantilever and the interaction with a s le of choice can be studied, a method often referred to as colloid probe microscopy. The AFM, or, more correctly, the scanning probe microscope, can thus be used to measure surface and frictional forces, the two foci of this article. There have been a wealth of force and friction measurements performed between an AFM tip and a surface, and many of the calibration and analysis issues are identical to those necessary for colloid probe work. We emphasize that this article confines itself primarily to elements of colloid probe measurement using the AFM.
Publisher: IOP Publishing
Date: 19-06-2004
Publisher: American Chemical Society (ACS)
Date: 24-12-2008
DOI: 10.1021/JA805169Z
Abstract: Vibrational sum-frequency spectroscopy (SFS) and total internal reflection Raman scattering (TIR Raman) have been used to study the adsorption of hexadecyltrimethylammonium bromide (CTAB) to hydrophilic silica. These two complementary techniques permit the determination of the adsorbed amount with a sensitivity of approximately 1% of the maximum surface coverage, changes in the average tilt of the adsorbed molecules, the presence of asymmetric aggregates in the adsorbed film, and the structure and orientation of the water molecules in the interfacial region. The TIR Raman spectra show a monotonic increase with CTAB concentration with no measurable changes in the relative intensities of the different polarization combinations probed, implying that no significant changes occur in the conformational order of the hydrocarbon chain. In the sum-frequency (SF) spectra, no detectable peaks from the surfactant headgroup and hydrophobic chain were observed at any surface coverage. Major changes are observed in the water bands of the SF spectra, as the originally negatively charged silica surface becomes positively charged with an increase in the adsorbed amount, inducing a change in the polar orientation of the water molecules near the surface. The detection limits for hydrocarbons chains in the SF spectra were estimated by comparison with the SF spectrum of a disordered octadecyltrichlorosilane monolayer. The simulations demonstrate that the asymmetry in the adsorbed CTAB layer at any concentration is less than 5% of a monolayer. The results obtained pose severe constraints on the possible structural models, in particular at concentrations below the critical micellar concentration where information is scarce. The formation of hemimicelles, monolayers and other asymmetric aggregates is ruled out, with centrosymmetric aggregates forming from early on in the adsorption process.
Publisher: Springer Science and Business Media LLC
Date: 06-12-2011
Publisher: American Chemical Society (ACS)
Date: 06-05-2011
DOI: 10.1021/JP111587E
Publisher: American Chemical Society (ACS)
Date: 22-04-2003
DOI: 10.1021/LA026569Q
Publisher: MDPI AG
Date: 11-2022
Abstract: (1) Background: Quorum sensing (QS) is the chemical communication between bacteria that sense chemical signals in the bacterial population to control phenotypic changes through the regulation of gene expression. The inhibition of QS has various potential applications, particularly in the prevention of bacterial infection. QS can be inhibited by targeting the LuxP, a periplasmic receptor protein that is involved in the sensing of the QS signaling molecule known as the autoinducer 2 (AI-2). The sensing of AI-2 by LuxP transduces the chemical information through the inner membrane sensor kinase LuxQ protein and activates the QS cascade. (2) Methods: An in silico approach was applied to design DNA aptamers against LuxP in this study. A method combining molecular docking and molecular dynamics simulations was used to select the oligonucleotides that bind to LuxP, which were then further characterized using isothermal titration calorimetry. Subsequently, the bioactivity of the selected aptamer was examined through comparative transcriptome analysis. (3) Results: Two aptamer candidates were identified from the ITC, which have the lowest dissociation constants (Kd) of 0.2 and 0.5 micromolar. The aptamer with the lowest Kd demonstrated QS suppression and down-regulated the flagellar-assembly-related gene expression. (4) Conclusions: This study developed an in silico approach to design an aptamer that possesses anti-QS properties.
Publisher: Elsevier BV
Date: 11-2006
DOI: 10.1016/J.JCIS.2006.06.070
Abstract: Four different cellulose model surfaces, and one silica surface, have been studied by means of atomic force microscopy (AFM). The normal interactions have been found to consist of a longer range double layer force with a short range steric interaction, the nature of which is extensively discussed. Both the surface charge and range of the steric force depend on the type of cellulose substrate used, as does the magnitude of the adhesion. Studies of friction reveal that surface roughness is the determining factor for the friction coefficient, with which it increases monotonically. The absolute value, however, is determined by the surface chemistry. All studied cellulose surfaces show similar behavior in response to xyloglucan addition.
Publisher: American Chemical Society (ACS)
Date: 19-03-2010
DOI: 10.1021/LA904697G
Abstract: X-ray reflectivity and vibrational sum frequency spectroscopy are used to probe the structure of the ethylammonium nitrate (EAN)-air interface. X-ray reflectivity reveals that the EAN-air interface is structured and consists of alternating nonpolar and charged layers that extend 31 A into the bulk. Vibrational sum frequency spectroscopy reveals interfacial cations have their ethyl moieties oriented toward air, with the CH(3) C(3) axis positioned approximately 36.5 degrees from interface normal. This structure is invariant between 15 and 51 degrees C. On account of its molecular symmetry, the orientation of the nitrate anion cannot be determined with certainty.
Publisher: Springer Science and Business Media LLC
Date: 06-08-2021
DOI: 10.1007/S11249-021-01485-Z
Abstract: Improving the tactile aesthetics of products that can be described as touch intensive is an increasing priority within many sectors, including the furniture industry. Understanding which physical characteristics contribute to the haptic experience of a surface, and how, is therefore highly topical. It has earlier been shown that both friction and topography affect tactile perception. Thus, two series of stimuli have been produced using standard coating techniques, with systematic variation in (physical) friction and roughness properties. This was achieved through appropriate selection of matting agents and resins. The stimuli sets were then evaluated perceptually to determine the extent to which discrimination between pairs of surfaces followed the systematic materials variation. In addition to investigating the role of the physical properties in discrimination of the surfaces, their influence on perceived pleasantness and naturalness was also studied. The results indicate that changes in tactile perception can be understood in terms of friction and roughness, and that varying the matting agents (topography) and resins (material properties) in the coatings provide the controlling factors for furniture applications. Perceived pleasantness is associated with low friction and smoother topography, whilst perceived naturalness is found to be described by an interaction between tactile friction and the average maximum peak height of the surface features. Graphic Abstract
Publisher: AIP Publishing
Date: 09-2013
DOI: 10.1063/1.4820345
Abstract: A technique has been developed for the calculation of torsional spring constants for AFM cantilevers based on the combination of the normal spring constant and plate/beam theory. It is easy to apply and allow the determination of torsional constants for stiff cantilevers where the thermal power spectrum is difficult to obtain due to the high resonance frequency and low signal/noise ratio. The applicability is shown to be general and this simple approach can thus be used to obtain torsional constants for any beam shaped cantilever.
Publisher: American Chemical Society (ACS)
Date: 09-03-2009
DOI: 10.1021/BM801467W
Abstract: Cellulosic model surfaces functionalized with chitosan, a naturally occurring cationic biomacromolecule, by in situ adsorption have been studied with an atomic force microscope (AFM) in colloidal probe configuration. The interaction forces on approach and separation, as well as the nanotribological properties, were shown to be highly pH-dependent, and a significant difference in the behavior was seen before and after chitosan adsorption. In general, all forces on approach showed a highly repulsive interaction at shorter distances due to deformation of the probe. At high pH, before chitosan adsorption, a long-range electrostatic repulsion was observed, consistent with DLVO theory. However, at low pH no electrostatic contribution was found before adsorption, probably due to charge neutralization of carboxyl groups. After chitosan adsorption, repulsive forces acting over a much longer distance than predicted by DLVO theory were present at low pH. This effect was ascribed to chain extension of the chitosan species of which the magnitude and the range of the force increased dramatically with higher charge at low pH. In all cases, a typical saw-tooth patterned adhesion was present, with pull-off events occurring at different separations. The frequency of these events after chitosan adsorption was greatly increased at longer distances. Additionally, the adsorbed chitosan markedly reduced the friction, where the largest effect was a 7-fold decrease of the friction coefficient observed at low pH.
Publisher: Royal Society of Chemistry (RSC)
Date: 2017
DOI: 10.1039/C7FD00176B
Abstract: It is an honour to be charged with providing the concluding remarks for a Faraday Discussion. As many have remarked before, it is nonetheless a prodigious task, and what follows is necessarily a personal, and probably perverse, view of a watershed event in the Chemical Physics of Electroactive materials. The spirit of the conference was captured in a single sentence during the meeting itself.By Andriy Yaroschuk in commenting on the work of Kelsey Hatzell (DOI: 10.1039/c6fd00243a). “It is the nexus between rheology, electrochemistry, colloid science and energy storage”. The current scientific climate is increasingly dominated by a limited number of global challenges, and there is thus a tendency for research to resemble a football match played by 6 year olds, where everyone on the field chases the (funding) ball instead of playing to their “discipline”. It is thus reassuring to see how the application of rigorous chemical physics is leading to ingenious new solutions for both energy storage and harvesting, via , for ex le, nanoactuation, electrowetting, ionic materials and nanoplasmonics. In fact, the same language of chemical physics allows seamless transition between applications as erse as mechano-electric energy generation, active moisture transport and plasmonic shutters – even the origins of life were addressed in the context of electro-autocatalysis!
Publisher: American Chemical Society (ACS)
Date: 27-05-2008
DOI: 10.1021/LA800260H
Abstract: We introduced the novel technique of AFM-porosimetry and applied it to measure the total pore volume of porous particles with a spherical geometry. The methodology is based on using an atomic force microscope as a balance to measure masses of in idual particles. Several particles within the same batch were measured, and by plotting particle mass versus particle volume, the bulk density of the s le can be extracted from the slope of the linear fit. The pore volume is then calculated from the densities of the bulk and matrix materials, respectively. In contrast to nitrogen sorption and mercury porosimetry, this method is capable of measuring the total pore volume regardless of pore size distribution and pore connectivity. In this study, three porous s les were investigated by AFM-porosimetry: one ordered mesoporous s le and two disordered foam structures. All s les were based on a matrix of amorphous silica templated by a block copolymer, Pluronic F127, swollen to various degrees with poly(propylene glycol). In addition, the density of silica spheres without a template was measured by two independent techniques: AFM and the Archimedes principle.
Publisher: American Chemical Society (ACS)
Date: 26-10-2012
DOI: 10.1021/LA3028989
Abstract: A novel type of block copolymer has been synthesized. It consists of a linear cationic block and an uncharged bottle-brush block. The nonionic bottle-brush block contains 45 units long poly(ethylene oxide) side chains. This polymer was synthesized with the intention of creating branched brush layers firmly physisorbed to negatively charged surfaces via the cationic block, mimicking the architecture (but not the chemistry) of bottle-brush molecules suggested to be present on the cartilage surface, and contributing to the efficient lubrication of synovial joints. The adsorption properties of the diblock copolymer as well as of the two blocks separately were studied on silica surfaces using quartz crystal microbalance with dissipation monitoring (QCM-D) and optical reflectometry. The adsorption kinetics data highlight that the diblock copolymers initially adsorb preferentially parallel to the surface with both the cationic block and the uncharged bottle-brush block in contact with the surface. However, as the adsorption proceeds, a structural change occurs within the layer, and the PEO bottle-brush block extends toward solution, forming a surface-anchored branched brush layer. As the adsorption plateau is reached, the diblock copolymer layer is 46-48 nm thick, and the water content in the layer is above 90 wt %. The combination of strong electrostatic anchoring and highly hydrated branched brush structures provide strong steric repulsion, low friction forces, and high load bearing capacity. The strong electrostatic anchoring also provides high stability of preadsorbed layers under different ionic strength conditions.
Publisher: AIP Publishing
Date: 29-01-2018
DOI: 10.1063/1.5001551
Abstract: Using neutron reflectivity, the electro-responsive structuring of the non-halogenated ionic liquid (IL) trihexyl(tetradecyl)phosphonium-bis(mandelato)borate, [P6,6,6,14][BMB], has been studied at a gold electrode surface in a polar solvent. For a 20% w/w IL mixture, contrast matched to the gold surface, distinct Kiessig fringes were observed for all potentials studied, indicative of a boundary layer of different composition to that of the bulk IL-solvent mixture. With applied potential, the litudes of the fringes from the gold-boundary layer interface varied systematically. These changes are attributable to the differing ratios of cations and anions in the boundary layer, leading to a greater or diminished contrast with the gold electrode, depending on the in idual ion scattering length densities. Such electro-responsive changes were also evident in the reflectivities measured for the pure IL and a less concentrated (5% w/w) IL-solvent mixture at the same applied potentials, but gave rise to less pronounced changes. These measurements, therefore, demonstrate the enhanced sensitivity achieved by contrast matching the bulk solution and that the structure of the IL boundary layers formed in mixtures is strongly influenced by the bulk concentration. Together these results represent an important step in characterising IL boundary layers in IL-solvent mixtures and provide clear evidence of electro-responsive structuring of IL ions in their solutions with applied potential.
Publisher: Wiley
Date: 17-03-2015
DOI: 10.1111/SRT.12227
Abstract: The tactile perception is essential for all types of topical formulations (cosmetic, pharmaceutical, medical device) and the possibility to predict the sensorial response by using instrumental methods instead of sensory testing would save time and cost at an early stage product development. Here, we report on an instrumental evaluation method using tactile friction measurements to estimate perceptual attributes of topical formulations. Friction was measured between an index finger and an artificial skin substrate after application of formulations using a force sensor. Both model formulations of liquid crystalline phase structures with significantly different tactile properties, as well as commercial pharmaceutical moisturizing creams being more tactile-similar, were investigated. Friction coefficients were calculated as the ratio of the friction force to the applied load. The structures of the model formulations and phase transitions as a result of water evaporation were identified using optical microscopy. The friction device could distinguish friction coefficients between the phase structures, as well as the commercial creams after spreading and absorption into the substrate. In addition, phase transitions resulting in alterations in the feel of the formulations could be detected. A correlation was established between skin hydration and friction coefficient, where hydrated skin gave rise to higher friction. Also a link between skin smoothening and finger friction was established for the commercial moisturizing creams, although further investigations are needed to analyse this and correlations with other sensorial attributes in more detail. The present investigation shows that tactile friction measurements have potential as an alternative or complement in the evaluation of perception of topical formulations.
Publisher: Royal Society of Chemistry (RSC)
Date: 2013
DOI: 10.1039/C3SM27862J
Publisher: American Chemical Society (ACS)
Date: 02-1993
DOI: 10.1021/LA00026A009
Publisher: Elsevier BV
Date: 05-1997
Publisher: American Chemical Society (ACS)
Date: 03-12-2005
DOI: 10.1021/JP047338Q
Abstract: Aqueous acetic acid solutions have been studied by vibrational sum frequency spectroscopy (VSFS) in order to acquire molecular information about the liquid-gas interface. The concentration range 0-100% acetic acid has been studied in the CH/OH and the C-O/C=O regions, and in order to clarify peak assignments, experiments with deuterated acetic acid and water have also been performed. Throughout the whole concentration range, the acetic acid is proven to be protonated. It is explicitly shown that the structure of a water surface becomes disrupted even at small additions of acetic acid. Furthermore, the spectral evolution upon increasing the concentration of acetic acid is explained in terms of the different complexes of acetic acid molecules, such as the hydrated monomer, linear dimer, and cyclic dimer. In the C=O region, the hydrated monomer is concluded to give rise to the sum frequency (SF) signal, and in the CH region, the cyclic dimer contributes to the signal as well. The combination of results from the CH/OH and the C-O/C=O regions allows a thorough characterization of the behavior of the acetic acid molecules at the interface to be obtained.
Publisher: CSIRO Publishing
Date: 2006
DOI: 10.1071/CH06206
Abstract: An SPM has been used to measure frictional interactions between two crossed fibres for the first time. The preparation of the surfaces is briefly described, but the crucial element is that the fibre attached to the AFM cantilever is glued parallel to the long axis. The fibres consist of polyester and frictional forces were measured both in air and solutions of cationic surfactant C14TAB. The friction coefficients reduce markedly with increasing concentration of surfactant which is ascribed to the formation of a boundary lubricating film between the surfaces. On removal of the solution, the subsequent friction coefficient in air was reduced by more than a factor of two compared to its value before immersion.
Publisher: American Chemical Society (ACS)
Date: 18-04-2003
DOI: 10.1021/LA026570P
Publisher: Mary Ann Liebert Inc
Date: 03-2007
Abstract: Self-assembling supramolecular complexes are of great interest for bottom-up research like nanotechnology. DNA is an inexpensive building block with sequence-specific self-assembling capabilities through Watson-Crick and/or Hoogsteen base pairing and could be used for applications in surface chemistry, material science, nanomechanics, nanoelectronics, nanorobotics, and of course in biology. The starting point is usually single-stranded DNA, which is rather easily accessible for base pairing and duplex formation. When long stretches of double-stranded DNA are desirable, serving either as genetic codes or electrical wires, bacterial expansion of plasmids is an inexpensive approach with scale-up properties. Here, we present a method for using double-stranded DNA of any sequence for generating simple structures, such as junctions and DNA lattices. It is known that supercoiled plasmids are strand-invaded by certain DNA analogs. Here we add to the complexity by using "Self-assembling UNiversal (SUN) anchors" formed by DNA analog oligonucleotides, synthesized with an extension, a "sticky-end" that can be used for further base pairing with single-stranded DNA. We show here how the same set of SUN anchors can be utilized for gene therapy, plasmid purification, junction for lattices, and plasmid dimerization through Watson-Crick base pairing. Using atomic force microscopy, it has been possible to characterize and quantify in idual components of such supra-molecular complexes.
Publisher: Elsevier BV
Date: 05-1997
Publisher: Elsevier BV
Date: 05-2011
Publisher: Royal Society of Chemistry (RSC)
Date: 2011
DOI: 10.1039/C0CP02144J
Abstract: Vibrational Sum Frequency Spectroscopy (VSFS) was employed to study adsorbing films of 4-Nitro Benzo-15-Crown-5 (NB15C5) and Benzo-15-Crown-5 (B15C5) at the aqueous solution-air interface. The surface of the solution is strongly influenced by the presence of crown ether species. Changes in the orientation of NB15C5 were monitored as a function of solution concentration, by targeting the ratio of peak intensities of the CN and NO(2) vibrational modes. The water of hydration has also been probed as a function of crown concentration, salt concentration, and temperature. The latter study strongly suggests that the surface can be treated as a charged interface, and that the associated ordered water decreases with increasing ionic strength of the bulk solution.
Publisher: Elsevier BV
Date: 12-2023
Publisher: American Chemical Society (ACS)
Date: 03-10-2019
DOI: 10.1021/ACS.LANGMUIR.9B02119
Abstract: The quartz crystal microbalance (QCM) has been used to study how the interfacial layer of an ionic liquid dissolved in a polar oil at low weight percentages responds to changes in applied potential. The changes in surface composition at the QCM gold surface depend on both the magnitude and sign of the applied potential. The time-resolved response indicates that the relaxation kinetics are limited by the diffusion of ions in the interfacial region and not in the bulk, since there is no concentration dependence. The measured mass changes cannot be explained only in terms of simple ion exchange the relative molecular volumes of the ions and the density changes in response to ion exclusion must be considered. The relaxation behavior of the potential between the electrodes upon disconnecting the applied potential is more complex than that observed for pure ionic liquids, but a measure of the surface charge can be extracted from the exponential decay when the rapid initial potential drop is accounted for. The adsorbed film at the gold surface consists predominantly of ionic liquid despite the low concentration, which is unsurprising given the surtactant-like structures of (some of) the ionic liquid ions. Changes in response to potential correspond to changes in the relative numbers of cations and anions, rather than a change in the oil composition. No evidence for an electric field induced change in viscosity is observed. This work shows conclusively that electric potentials can be used to control the surface composition, even in an oil-based system, and paves the way for other ion solvent studies.
Publisher: Royal Society of Chemistry (RSC)
Date: 2013
DOI: 10.1039/C3CP52638K
Abstract: Colloid probe atomic force microscopy (AFM) has been employed to investigate the nanotribology of the ionic liquid (IL)-Au(111) interface. Data is presented for four ILs, 1-ethyl-3-methylimidazolium tris(pentafluoroethyl)trifluorophosphate ([EMIM] FAP), 1-butyl-3-methylimidazolium tris(pentafluoroethyl)trifluorophosphate ([BMIM] FAP), 1-hexyl-3-methylimidazolium tris(pentafluoroethyl)trifluorophosphate ([HMIM] FAP) and 1-butyl-3-methylimidazolium iodide ([BMIM] I), at different Au(111) surface potentials. Lateral forces vary as a function of applied surface potential and ion structure because the composition of the confined ion layer changes from cation-enriched (at negative potentials) to mixed (at 0 V), and to anion-enriched (at positive potentials). ILs with FAP(-) anions all exhibit similar nanotribology: low friction at negative potentials and higher friction at positive potentials. [BMIM] I displays the opposite behaviour, as an I(-) anion-enriched layer is more lubricating than either the [BMIM](+) or FAP(-) layers. The effect of cation charged group (charge-delocalised versus charged-localised) was investigated by comparing [BMIM] FAP with 1-butyl-1-methylpyrrolidinium tris(pentafluoroethyl)trifluorophosphate ([Py(1,4)] FAP). [BMIM] FAP is less lubricating at negative potentials, but more lubricating at positive potentials. This indicated that even at positive potentials the cation concentration in the boundary layer is sufficiently high to influence lubricity. The influence of sliding velocity on lateral force was investigated for the [EMIM] FAP-Au(111) system. At neutral potentials the behaviour is consistent with a discontinuous sliding process. When a positive or negative potential bias is applied, this effect is less pronounced as the colloid probe slides along a better defined ion plane.
Publisher: Springer Berlin Heidelberg
Date: 2010
Publisher: Elsevier BV
Date: 03-2010
DOI: 10.1016/J.CIS.2009.12.002
Abstract: Mixtures of the two non-ionic surfactants hexaoxyethylene dodecyl ether (C(12)E(6)) and n-dodecyl-beta-D-maltoside (beta-C(12)G(2)) were studied with regard to surface properties, bulk properties, foam films, and foams. The reason for studying a mixture of an ethylene oxide (C(i)E(j)) and a sugar (C(n)G(m)) based surfactant is that despite being non-ionic, these two surfactants behave quite differently. Firstly, the physico-chemical properties of aqueous solutions of C(n)G(m) surfactants are less temperature-sensitive than those of C(i)E(j) solutions. Secondly, the surface charge density q(0) of foam films stabilized by C(n)G(m) surfactants is pH insensitive down to the so-called isoelectric point, while that of foam films stabilized by C(i)E(j) surfactants changes linearly with the pH. The third difference is related to interaction forces between solid surfaces. Under equilibrium conditions very high forces are needed to expel beta-C(12)G(2) from between thiolated gold surfaces, while for C(12)E(6) low loads are sufficient. Fourthly, the adsorption of C(12)E(6) and beta-C(12)G(2) on hydrophilic silica and titania, respectively, is inverted. While the surface excess of C(12)E(6) is large on silica and negligible on titania, beta-C(12)G(2) adsorbs very little on silica but has a large surface excess on titania. What is the reason for this different behaviour? Under similar conditions and for comparable head group sizes, it was found that the hydration of C(i)E(j) surfactants is one order of magnitude higher but on average much weaker than that of C(n)G(m) surfactants. Moreover, C(n)G(m) surfactants possess a rigid maltoside unit, while C(i)E(j) surfactants have a very flexible hydrophilic part. Indeed, most of the different properties mentioned above can be explained by the different hydration and the head group flexibilities. The intriguing question of how mixtures of C(i)E(j) and C(n)G(m) surfactants would behave arises organically. Thus various properties of C(12)E(6)+beta-C(12)G(2) mixtures in aqueous solution have been studied with a focus on the 1:1 mixture. The results are compared with those of the single surfactants and are discussed accordingly.
Publisher: American Chemical Society (ACS)
Date: 02-2010
DOI: 10.1021/LA9047243
Abstract: The adsorbed layers of polyoxyethylene n-alkyl ether surfactants C(12)E(4), C(14)E(4), and C(16)E(4) at the EAN surface have a headgroup layer that is thin and compact (only approximately 30 vol % EAN). The headgroups do not adopt a preferred orientation and are disordered within the ethylene oxide layer. Alkyl tails contain a significant number of gauche defects indicating a high degree of conformational disorder. The thickness of the tail layer increases with increasing alkyl chain length, while the headgroup layer shows little change. Lowering the C(12)E(4) concentration from 1 to 0.1 wt % decreases the adsorbed amount, and the headgroup layer becomes thinner and less solvated, whereas C(14)E(4) and C(16)E(4) adsorbed layers are unaffected by dilution over the same concentration range. The C(16)E(4) layer thickness increases and area per molecule decreases on warming to 60 degrees C, but the adsorbed layer structures of C(12)E(4) and C(14)E(4) are unchanged. Both effects are attributed to surfactant solubility.
Publisher: American Chemical Society (ACS)
Date: 03-12-2005
DOI: 10.1021/JP047337Y
Abstract: Vibrational sum frequency spectroscopy has been used to investigate the surface of aqueous acetic acid solutions. By studying the methyl and carbonyl vibrations with different polarization combinations, an orientation analysis of the acetic acid molecules has been performed in the concentration range 0-100%. The surface tension of acetic acid solutions was also measured in order to obtain the surface concentration. The orientation of the interfacial acetic acid molecules was found to remain essentially constant in an upright position with the methyl group directed toward the gas phase in the whole concentration range. The tilt angle (theta(CH)3) of the symmetry axis of the methyl group with respect to the surface normal was found to be lower than 15 degrees when considering a delta distribution of angles or as narrow as 0 +/- 11 degrees when assuming a Gaussian distribution. Further investigations showed that the C=O bond tilt (theta(C)(=)(O)) of the acetic acid hydrated monomer was constant and close to 55 degrees in the concentration range where it was detected. Finally, the orientation information is discussed in terms of different species of acetic acid, where the formation of a surface layer of acetic acid cyclic dimers is proposed at high acid concentrations.
Publisher: Informa UK Limited
Date: 2002
Publisher: Springer Science and Business Media LLC
Date: 12-09-2013
DOI: 10.1038/SREP02617
Publisher: Elsevier BV
Date: 09-1996
Publisher: Royal Society of Chemistry (RSC)
Date: 2004
DOI: 10.1039/B314060C
Publisher: Royal Society of Chemistry (RSC)
Date: 2014
DOI: 10.1039/C4CP00512K
Abstract: The morphology and molecular conformation of monolayers of straight chain and methyl-branched fatty acids have been investigated by VSFS and AFM, revealing domains in the latter case, due to inverse micellar packing constraints.
Publisher: American Chemical Society (ACS)
Date: 21-04-2006
DOI: 10.1021/LA053011K
Abstract: Adhesion forces between different protein layers adsorbed on different substrates in aqueous media have been measured by means of an atomic force microscope using the colloid probe technique. The effects of the loading force, the salt concentration and pH of the medium, and the electrolyte type on the strength, the pull-off distance, and the separation energy of such adhesion forces have been analyzed in depth. Two very different proteins (bovine serum albumin and apoferritin) and two dissimilar substrates (silica and polystyrene) were used in the experiments. The results clearly point out a very important contribution of the electrostatic interactions in the adhesion between protein layers.
Publisher: American Chemical Society (ACS)
Date: 06-10-2010
DOI: 10.1021/LA1030729
Abstract: Polyelectrolyte multilayer films containing nanocrystalline cellulose (NCC) and poly(allylamine hydrochloride) (PAH) make up a new class of nanostructured composite with applications ranging from coatings to biomedical devices. Moreover, these materials are amenable to surface force studies using colloid-probe atomic force microscopy (CP-AFM). For electrostatically assembled films with either NCC or PAH as the outermost layer, surface morphology was investigated by AFM and wettability was examined by contact angle measurements. By varying the surrounding ionic strength and pH, the relative contributions from electrostatic, van der Waals, steric, and polymer bridging interactions were evaluated. The ionic cross-linking in these films rendered them stable under all solution conditions studied although swelling at low pH and high ionic strength was inferred. The underlying polymer layer in the multilayered film was found to dictate the dominant surface forces when polymer migration and chain extension were facilitated. The precontact normal forces between a silica probe and an NCC-capped multilayer film were monotonically repulsive at pH values where the material surfaces were similarly and fully charged. In contrast, at pH 3.5, the anionic surfaces were weakly charged but the underlying layer of cationic PAH was fully charged and attractive forces dominated due to polymer bridging from extended PAH chains. The interaction with an anionic carboxylic acid probe showed similar behavior to the silica probe however, for a cationic amine probe with an anionic NCC-capped film, electrostatic double-layer attraction at low pH, and electrostatic double-layer repulsion at high pH, were observed. Finally, the effect of the capping layer was studied with an anionic probe, which indicated that NCC-capped films exhibited purely repulsive forces which were larger in magnitude than the combination of electrostatic double-layer attraction and steric repulsion, measured for PAH-capped films. Wherever possible, DLVO theory was used to fit the measured surface forces and apparent surface potentials and surface charge densities were calculated.
Publisher: American Chemical Society (ACS)
Date: 26-08-1999
DOI: 10.1021/LA990322K
Publisher: Royal Society of Chemistry (RSC)
Date: 2016
DOI: 10.1039/C5CP07061A
Abstract: The efficacy of ionic liquids (ILs) as lubricant additives to a model base oil has been probed at the nanoscale and macroscale as a function of IL concentration using the same materials.
Publisher: Springer Science and Business Media LLC
Date: 19-04-2018
DOI: 10.1038/S41598-018-23688-6
Abstract: It is known that roughness-smoothness, hardness-softness, stickiness-slipperiness and warm-cold are predominant perceptual dimensions in macro-, micro- and nano- texture perception. However, it is not clear to what extent active tactile texture discrimination remains intact with age. The general decrease in tactile ability induces physical and emotional dysfunction in elderly, and has increasing significance for an aging population. We report a method to quantify tactile acuity based on blinded active exploration of systematically varying micro-textured surfaces and a same-different paradigm. It reveals that elderly participants show significantly reduced fine texture discrimination ability. The elderly group also displays statistically lower finger friction coefficient, moisture and elasticity, suggesting a link. However, a subpopulation of the elderly retains discrimination ability irrespective of cutaneous condition and this can be related to a higher density of somatosensory receptors on the finger pads. Skin tribology is thus not the primary reason for decline of tactile discrimination with age. The remediation of cutaneous properties through rehydration, however leads to a significantly improved tactile acuity. This indicates unambiguously that neurological tactile loss can be temporarily compensated by restoring the cutaneous contact mechanics. Such mechanical restoration of tactile ability has the potential to increase the quality of life in elderly.
Publisher: American Chemical Society (ACS)
Date: 18-04-2003
DOI: 10.1021/LA026571H
Publisher: Royal Society of Chemistry (RSC)
Date: 2012
DOI: 10.1039/C2NR30536D
Abstract: The adhesive properties of gastroliths from a freshwater crayfish (Cherax quadricarinatus) were quantified by colloidal probe atomic force microscopy (AFM) between heavily demineralized gastrolith microparticles and gastrolith substrates of different composition. Combined AFM and transmission electron microscopy studies demonstrated that the sequential detachment and large adhesion energies that characterise the adhesive behaviour of a native gastrolith substrate are dominated by sacrificial bonds between chitin fibres and between chitin fibres and CaCO(3). The sacrificial bonds were shown to be strongly related to the gastrolith proteins and when the majority of these proteins were removed by ethylenediaminetetraacetic acid (EDTA), the sequential detachment disappeared and the adhesive energy was reduced by more than two orders of magnitude.
Publisher: Elsevier BV
Date: 03-2020
DOI: 10.1016/J.JCIS.2019.12.045
Abstract: The stiffness has been found to regulate hydrogel performances and applications. However, the key interfacial properties of hydrogels, like friction and adhesion are not controlled by the stiffness, but are altered by the structure and composition of hydrogels, like polymer volume fraction and crosslinking degree. Colloidal probe atomic force microscopy has been use to investigate the relationship between tribological properties (friction and adhesion) and composition of hydrogels with similar stiffness, but different polymer volume fractions and crosslinking degrees. The interfacial normal and lateral (friction) forces of hydrogels are not directly correlated to the stiffness, but altered by the hydrogel structure and composition. For normal force measurements, the adhesion increases with polymer volume fraction but decreases with crosslinking degree. For lateral force measurements, friction increases with polymer volume fraction, but decreases with crosslinking degree. In the low normal force regime, friction is mainly adhesion-controlled and increases significantly with the adhesion and polymer volume fraction. In the high normal force regime, friction is predominantly load-controlled and shows slow increase with normal force.
Publisher: Royal Society of Chemistry (RSC)
Date: 04-07-2014
DOI: 10.1039/C4CP02320J
Abstract: The effect of ionic liquid (IL) molecular structure on nanoscale friction has been investigated using colloidal probe Friction Force Microscopy (FFM). The ILs studied were ethylammonium formate (EAF), ethylammonium nitrate (EAN), propylammonium formate (PAF), propylammonium nitrate (PAN), dimethylethylammonium formate (DMEAF), and ethanolammonium nitrate (EtAN). ILs were confined between a silica colloid probe and a mica surface, and the friction force was measured as a function of normal load for sliding velocities between 10 and 40 μm s(-1). At low normal forces, multiple IL layers are found between the probe and the surface, but at higher force, in the boundary layer regime, a single ion layer separates the probe and the surface. In the boundary layer regime energy is dissipated by two main pathways. Firstly, the ionic liquid near the surface, with the exception of the boundary layer, is expelled from the advancing contact made by the probe on the surface. This disruption in the interactions between the boundary layer and the near surface multilayers, leads to energy dissipation and depends on the strength of the attraction between the boundary and near surface layers. The second pathway is via rotations and twists of ions in the boundary layer, primarily associated with the cation terminal methyl group. The friction coefficient did not vary over the limited range of sliding speeds investigated.
Publisher: American Association for the Advancement of Science (AAAS)
Date: 02-04-2021
Abstract: Atomic defects in 2D materials show excellent spin coherence time and become promising contenders for quantum applications.
Publisher: American Chemical Society (ACS)
Date: 23-07-1999
DOI: 10.1021/LA9815852
Publisher: American Chemical Society (ACS)
Date: 11-11-2005
DOI: 10.1021/JA053289Z
Abstract: The OH stretching region of water molecules in the vicinity of nonionic surfactant monolayers has been investigated using vibrational sum frequency spectroscopy (VSFS) under the polarization combinations ssp, ppp, and sps. The surface sensitivity of the VSFS technique has allowed targeting the few water molecules present at the surface with a net orientation and, in particular, the hydration shell around alcohol, sugar, and poly(ethylene oxide) headgroups. Dramatic differences in the hydration shell of the uncharged headgroups were observed, both in comparison to each another and in comparison to the pure water surface. The water molecules around the rigid glucoside and maltoside sugar rings were found to form strong hydrogen bonds, similar to those observed in tetrahedrally coordinated water in ice. In the case of the poly(ethylene oxide) surfactant monolayer a significant ordering of both strongly and weakly hydrogen bonded water was observed. Moreover, a band common to all the surfactants studied, clearly detected at relatively high frequencies in the polarization combinations ppp and sps, was assigned to water species located in proximity to the surfactant hydrocarbon tail phase, with both hydrogen atoms free from hydrogen bonds. An orientational analysis provided additional information on the water species responsible for this band.
Publisher: American Chemical Society (ACS)
Date: 27-07-2009
DOI: 10.1021/NL901411E
Abstract: This study reports on a direct approach of quantitatively probing the nanotribological response of chemically end-grafted polyions. A combination of a quartz crystal microbalance with dissipation and atomic force microscopy, in the now well established colloidal probe mode, was utilized to investigate the stimuli-induced lubrication behavior between poly(2-(dimethylamino)ethyl methacrylate) grafts on gold. Force and friction measurements showed reversible transitions of up to an order of magnitude difference induced by varying the solvent conditions. The greatly enhanced lubrication observed at low pH was attributed to the formation of a repulsive, highly charged, hydrated cushion. At high pH the friction was significantly increased. The system turned attractive above the lower critical solution temperature with a small friction reduction interpreted as being due to nanoscopic flattening at the interfacial boundary.
Publisher: American Chemical Society (ACS)
Date: 30-04-2013
DOI: 10.1021/LA400468F
Abstract: The friction anisotropy of human hair has been investigated as a function of angle using AFM fiber probe measurements to evaluate the role of cuticle alignment. It is found that friction hysteresis, the difference in friction coefficients between sliding with or against the cuticle direction, is essentially nonexistent for native human hair. For damaged human hair, however, a clear friction hysteresis is observed, which appears to be a periodic function of the angle between the fibers. The implication is that antiparallel sliding is not in itself sufficient for friction isotropy but that lifting of the cuticle edges is required. A methodology to perform friction analysis independently for trace and retrace was therefore developed, which is applicable to any type of AFM lateral force measurement. It explicitly accounts for roll, noncircular cross section, and off-axis alignment as well as baseline drift, which allows real anisotropy in the friction coefficient to be deconvoluted from these artifacts.
Publisher: American Chemical Society (ACS)
Date: 04-1994
DOI: 10.1021/LA00016A024
Publisher: American Physical Society (APS)
Date: 15-06-1998
Publisher: American Chemical Society (ACS)
Date: 30-07-2015
Publisher: American Chemical Society (ACS)
Date: 05-03-2013
DOI: 10.1021/BM301790B
Abstract: Cellulose microspheres bearing poly(ε-caprolactone) grafts of different molecular weights were investigated to evaluate the effect of graft length on the interfacial properties. Surface force and friction measurements were performed using an atomic force microscope in colloidal probe mode. The maximum interaction distance and adhesion is dependent on the temperature and the time in contact via a diffusion controlled mechanism. The effects are highest for the longer grafts, and molecular weight thresholds were found to lie between 21 and 34 kDa at 25 °C and between 9 and 21 kDa at 40 °C. The interpenetration of the graft into a matrix leads to "hidden length" contributions to adhesion, analogous to those in natural biocomposites. The nanotribology results display Amontonian behavior, and the friction force at zero applied load is higher at the graft-graft interface than for a bare cellulose sphere interacting with the graft. These results clearly demonstrate the benefits of the grafted polymer layer on the adhesion, toughness, and resistance to shear in the design of cellulosic nanobiocomposites.
Publisher: American Chemical Society (ACS)
Date: 09-02-2008
DOI: 10.1021/BM701214E
Abstract: This study focuses on the manufacture and characterization of model surfaces consisting of end-grafted xyloglucan (XG), a naturally occurring polysaccharide, onto a gold substrate. The now well-established XET-technology was utilized for enzymatic incorporation of a thiol moiety at one end of the xyloglucan backbone. This functionalized macromolecule was subsequently top-down grafted to gold, forming a thiol-bonded xyloglucan brushlike layer. The grafting was monitored in situ with QCM-D, and a significant difference in the adsorbed/grafted amount between unmodified xyloglucan and the thiol-functionalized polymer was observed. The grafted surface was demonstrated to be accessible to enzyme digestion using the plant endo-xyloglucanase TmNXG1. The nanotribological properties toward cellulose of the untreated crystal, brush-modified surface, and enzyme-exposed surfaces were compared with a view to understanding the role of xyloglucan in friction reduction. Friction coefficients obtained by the AFM colloidal probe technique using a cellulose functionalized probe on the xyloglucan brush showed an increase of a factor of 2 after the enzyme digestion, and this result is interpreted in terms of surface roughness. Finally, the brush is shown to exhibit binding to cellulose despite its highly oriented nature.
Publisher: Springer Science and Business Media LLC
Date: 23-01-2015
DOI: 10.1038/NCOMMS7031
Publisher: American Chemical Society (ACS)
Date: 15-07-2003
DOI: 10.1021/LA034281A
Publisher: Royal Society of Chemistry (RSC)
Date: 2020
DOI: 10.1039/D0CP00360C
Abstract: Control of the interfacial structures of ionic liquids (ILs) at charged interfaces is important to many of their applications, including in energy storage solutions, sensors and advanced lubrication technologies utilising electric fields.
Publisher: American Chemical Society (ACS)
Date: 27-05-2006
DOI: 10.1021/BM060100I
Abstract: The forces and friction between cellulose spheres have been measured in the absence and presence of xyloglucan using an atomic force microscope. The forces between cellulose are monotonically repulsive with negligible adhesion after contact is achieved. The friction coefficient is observed to be unusually high in comparison with other nanotribological systems. We have confirmed that xyloglucan adsorbs strongly to cellulose, which results in a much stronger adhesion, which is dependent on the time the surfaces are in contact. Xyloglucan also increases the repulsion on approach of the cellulose surfaces, and the friction is markedly reduced. The apparently incompatible observations of decreased friction in combination with increased adhesion fulfills many of the necessary criteria for a papermaking additive.
Publisher: American Chemical Society (ACS)
Date: 16-12-2000
DOI: 10.1021/LA990961V
Publisher: American Chemical Society (ACS)
Date: 04-01-2000
DOI: 10.1021/LA990824Y
Abstract: Forces have been measured for hexadecyltrimethylammonium salicylate (C(16)TASal) layers on glass beads. During the inward process, hydrophobic attraction occurred at lower adsorption of C(16)TASal and electrostatic repulsion interactions happened at higher adsorption. While the jump-in phenomenon was observed for solutions of concentrations below the critical micelle concentration (cmc = 0.15 mM), the step-in phenomenon was characteristic for solutions at the cmc and above the cmc, suggesting the push-out of adsorbed C(16)TASal layers and/or inserted micelles. The remarkable pull-off phenomenon on the outward process occurred for all solutions, indicating a strong interaction between C(16)TASal molecules. For aqueous 0.15 mM C(16)TASal solutions of various NaSal concentrations, on the inward process, the electrostatic repulsive interaction decreased with adding NaSal. This is due to the electrostatic shielding by salt excess. The height of the force wall on the inward process reached a maximum at 0.01 M NaSal, but the interlocking between molecules on two surfaces during the outward process was minimized at 0.1 M NaSal. These tendencies, which are different from that of the electrostatic repulsion interaction, imply the strong cohesion between adsorbed C(16)TASal layers.
Publisher: Oxford University Press (OUP)
Date: 06-09-2013
DOI: 10.1093/BRAIN/AWT233
Publisher: AIP Publishing
Date: 11-2006
DOI: 10.1063/1.2387891
Abstract: The photodiode sensitivity in the atomic force microscope is calibrated by relating the voltage noise to the thermal fluctuations of the cantilever angle. The method accounts for the ratio of the thermal fluctuations measured in the fundamental vibration mode to the total, and also for the tilt and extended tip of the cantilever. The method is noncontact and is suitable for soft or deformable surfaces where the constant compliance method cannot be used. For hard surfaces, the method can also be used to calibrate the cantilever spring constant.
Publisher: Wiley
Date: 05-12-2013
Abstract: Australian and New Zealand radiation oncologists with an interest in uro-oncology were invited to participate in a pattern-of-practice survey dealing with the management of intact high-risk prostate cancer. Responses from 46 practitioners (representing 73% of all potential respondents) revealed that high-dose radiation therapy is the standard of care. However, there is variability in practice with regard to the methods used to achieve dose escalation, the use of whole-pelvic radiation therapy and the optimal duration of androgen deprivation therapy employed. A review of the literature outlining the current body of knowledge and the planned and ongoing studies in intact high-risk prostate cancer is presented.
Publisher: Springer Science and Business Media LLC
Date: 30-05-2023
DOI: 10.1038/S41467-023-38436-2
Abstract: The spatial sorting of RNA transcripts is fundamental for the refinement of gene expression to distinct subcellular regions. Although, in non-mammalian early embryogenesis, differential RNA localisation presages cell fate determination, in mammals it remains unclear. Here, we uncover apical-to-basal RNA asymmetries in outer blastomeres of 16-cell stage mouse preimplantation embryos. Basally directed RNA transport is facilitated in a microtubule- and lysosome-mediated manner. Yet, despite an increased accumulation of RNA transcripts in basal regions, higher translation activity occurs at the more dispersed apical RNA foci, demonstrated by spatial heterogeneities in RNA subtypes, RNA-organelle interactions and translation events. During the transition to the 32-cell stage, the biased inheritance of RNA transcripts, coupled with differential translation capacity, regulates cell fate allocation of trophectoderm and cells destined to form the pluripotent inner cell mass. Our study identifies a paradigm for the spatiotemporal regulation of post-transcriptional gene expression governing mammalian preimplantation embryogenesis and cell fate.
Publisher: Royal Society of Chemistry (RSC)
Date: 2013
DOI: 10.1039/C3CC42844C
Publisher: Elsevier BV
Date: 09-2007
DOI: 10.1016/J.JCIS.2007.05.016
Abstract: The atomic force microscope has been used to investigate normal surface forces and lateral friction forces at different concentrations of sodium oleate, a frequently used fatty acid in the deinking process. The measurements have been performed using the colloidal probe technique with bead materials consisting of cellulose and silica. Cellulose was used together with a printing ink alkyd resin and mica, whereas silica was used with a hydrophobized silica wafer. The cellulose-alkyd resin system showed stronger double layer repulsion and the friction was reduced with increasing surfactant concentration. The adhesive interaction disappeared immediately on addition of sodium oleate. The normal surface forces for cellulose-mica indicated no apparent adsorption of the sodium oleate however, the friction coefficient increased on addition of sodium oleate, which we ascribe to some limited adsorption increasing the effective surface roughness. The silica-hydrophobic silica system showed a completely different surface force behavior at the different concentrations. An attractive hydrophobic interaction was evident since the surfaces jumped into adhesive contact at a longer distance than the van der Waals forces would predict. The strong adhesion was reflected in the friction forces as a nonlinear relationship between load and friction and a large friction response at zero applied load. Indirect evidence of adsorption to the hydrophilic silica surface was also observed in this case, and QCM studies were performed to confirm the adsorption of material to both surfaces.
Publisher: Elsevier BV
Date: 03-1994
Publisher: American Chemical Society (ACS)
Date: 08-12-2007
DOI: 10.1021/LA060456F
Abstract: Friction force measurements have been conducted with a colloid probe on mica and silica (both hydrophilic and hydrophobized) after long (24 h) exposure to high-humidity air. Adhesion and friction measurements have also been performed on cellulose substrates. The long exposure to high humidity led to a large hysteresis between loading and unloading in the friction measurements with separation occurring at large negative applied loads. The large hysteresis in the friction-load relationship is attributed to a contact area hysteresis of the capillary condensate which built up during loading and did not evaporate during the unloading regime. The magnitude of the friction force varied dramatically between substrates and was lowest on the mica substrate and highest on the hydrophilic silica substrate, with the hydrophobized silica and cellulose being intermediate. The adhesion due to capillary forces on cellulose was small compared to that on the other substrates, due to the greater roughness of these surfaces.
Publisher: Royal Society of Chemistry (RSC)
Date: 2013
DOI: 10.1039/C3SM50578B
Publisher: Springer Science and Business Media LLC
Date: 06-11-2009
Publisher: Springer Science and Business Media LLC
Date: 11-04-2013
Publisher: Royal Society of Chemistry (RSC)
Date: 2020
DOI: 10.1039/D0CP02736G
Abstract: Neutron reflectivity and atomic force microscopy results reveal the electroresponsive interfacial structuring and nano-frictional properties of ionic liquid (IL) lubricant mixtures with a polar solvent are strongly dependent on bulk IL concentration.
Publisher: MDPI AG
Date: 14-11-2018
Abstract: We investigate the interfacial properties of the non-halogenated ionic liquid (IL), trihexyl(tetradecyl)phosphonium bis(mandelato)borate, [P6,6,6,14][BMB], in proximity to solid surfaces, by means of surface force measurement. The system consists of sharp atomic force microscopy (AFM) tips interacting with solid surfaces of mica, silica, and gold. We find that the force response has a monotonic form, from which a characteristic steric decay length can be extracted. The decay length is comparable with the size of the ions, suggesting that a layer is formed on the surface, but that it is diffuse. The long alkyl chains of the cation, the large size of the anion, as well as crowding of the cations at the surface of negatively charged mica, are all factors which are likely to oppose the interfacial stratification which has, hitherto, been considered a characteristic of ionic liquids. The variation in the decay length also reveals differences in the layer composition at different surfaces, which can be related to their surface charge. This, in turn, allows the conclusion that silica has a low surface charge in this aprotic ionic liquid. Furthermore, the effect of temperature has been investigated. Elevating the temperature to 40 °C causes negligible changes in the interaction. At 80 °C and 120 °C, we observe a layering artefact which precludes further analysis, and we present the underlying instrumental origin of this rather universal artefact.
Publisher: American Chemical Society (ACS)
Date: 13-07-2007
DOI: 10.1021/JP070246R
Publisher: Royal Society of Chemistry (RSC)
Date: 2011
DOI: 10.1039/C0CP00604A
Abstract: The surface of aqueous solutions of 4-Nitro Benzo-15-Crown-5 (NB15C5) and Benzo-15-Crown-5 (B15C5) has been studied using the surface sensitive technique vibrational sum frequency spectroscopy (VSFS). The NO, CN, COC and CH vibrational modes of these compounds at the air-water interface as well as OH vibrational modes of the surface water hydrating this compound have been targeted in order to obtain molecular information about arrangement and conformation of the adsorbed crown ether molecules at the air-water interface. The CH(2) vibrational modes of crown ethers have been identified and found to be split due to interaction with ether oxygen. The spectra provide evidence for the existence of a protonated crown complex moiety at the surface leading to the appearance of strongly ordered water species. The interfacial water species are influenced by the resulting charged interface and by the strong Zundel polarizability due to tunneling of the proton species between equivalent sites within the crown ring.
Publisher: AIP Publishing
Date: 08-2005
DOI: 10.1063/1.2006407
Abstract: Presented here is a novel technique for the in situ calibration and measurement of friction with the atomic force microscope that can be applied simultaneously with the normal force measurement. The method exploits the fact that the cantilever sits at an angle of about 10° to the horizontal, which causes the tip (or probe) to slide horizontally over the substrate as a normal force run is performed. This sliding gives rise to an axial friction force (in the axial direction of the cantilever), which is measured through the difference in the constant compliance slopes of the inward and outward traces. Traditionally, friction is measured through lateral scanning of the substrate, which is time consuming, and requires an ex situ calibration of both the torsional spring constant and the lateral sensitivity of the photodiode detector. The present method requires no calibration other than the normal spring constant and the vertical sensitivity of the detector, which is routinely done in the force analysis. The present protocol can also be applied to preexisting force curves, and, in addition, it provides the means to correct force data for cantilevers with large probes.
Publisher: American Chemical Society (ACS)
Date: 08-1993
DOI: 10.1021/LA00032A008
Publisher: American Chemical Society (ACS)
Date: 12-2001
DOI: 10.1021/LA011037F
Publisher: Elsevier BV
Date: 05-2016
DOI: 10.1016/J.JCIS.2016.01.076
Abstract: Quartz crystal microbalance with dissipation (QCM-D) analysis of the hexa-l-Leucine (PLL)-catalyzed epoxidation of chalcone gives in-situ experimental evidences which demonstrate that the reaction proceeds mainly via the formation of a PLL-bound hydroperoxide complex followed by the reversible addition of chalcone. The observations offer an alternative rationalization for the viability of the preferred catalytic pathway.
Publisher: American Chemical Society (ACS)
Date: 19-06-2012
DOI: 10.1021/LA3010807
Abstract: The friction and adhesion between pairs of materials (silica, alumina, and polytetrafluoroethylene) have been studied and interpreted in terms of the long-ranged interactions present. In ambient laboratory air, the interactions are dominated by van der Waals attraction and strong adhesion leading to significant frictional forces. In the presence of the ionic liquid (IL) ethylammonium nitrate (EAN) the van der Waals interaction is suppressed and the attractive/adhesive interactions which lead to "stiction" are removed, resulting in an at least a 10-fold reduction in the friction force at large applied loads. The friction coefficient for each system was determined coefficients obtained in air were significantly larger than those obtained in the presence of EAN (which ranged between 0.1 and 0.25), and variation in the friction coefficients between systems was correlated with changes in surface roughness. As the viscosity of ILs can be relatively high, which has implications for the lubricating properties, the hydrodynamic forces between the surfaces have therefore also been studied. The linear increase in repulsive force with speed, expected from hydrodynamic interactions, is clearly observed, and these forces further inhibit the potential for stiction. Remarkably, the viscosity extracted from the data is dramatically reduced compared to the bulk value, indicative of a surface ordering effect which significantly reduces viscous losses.
Publisher: American Chemical Society (ACS)
Date: 12-06-2008
DOI: 10.1021/LA800402S
Abstract: Hydroxyapatite is a very interesting material given that it is the main component in tooth enamel and because of its uses in bone implant applications. Therefore, not only the characterization of its surface is of high relevance but also designing reliable methods to study the interfacial properties of films adsorbed onto it. In this paper we apply the colloidal probe atomic force microscopy method to investigate the surface properties of commercially available hydroxyapatite surfaces (both microscopic particles and macroscopic discs) in terms of interfacial and frictional forces. In this way, we find that hydroxyapatite surfaces at physiological relevant conditions are slightly negatively charged. The surfaces were then exposed to human whole saliva, and the surface properties were re-evaluated. A thick film was formed that was very resistant to mechanical stress. The frictional measurements demonstrated that the film was indeed highly lubricating, supporting the argument that this system may prove to be a relevant model for evaluating dental and implant systems.
Publisher: Informa UK Limited
Date: 2004
Publisher: Institution of Engineering and Technology (IET)
Date: 2006
Publisher: American Chemical Society (ACS)
Date: 23-12-1998
DOI: 10.1021/LA980848P
Publisher: Elsevier BV
Date: 05-2010
Publisher: American Chemical Society (ACS)
Date: 06-1990
DOI: 10.1021/LA00096A010
Publisher: Elsevier BV
Date: 12-2001
Publisher: Elsevier BV
Date: 10-2000
Publisher: IOP Publishing
Date: 03-2007
Publisher: Royal Society of Chemistry (RSC)
Date: 2020
DOI: 10.1039/D0CP05110A
Abstract: The influence of ambient levels of water on the electroresponsive interfacial structuring and nanofriction of ionic liquid lubricant mixtures has been investigated by neutron reflectivity and atomic force microscopy.
Publisher: Royal Society of Chemistry (RSC)
Date: 2017
DOI: 10.1039/C7CP01772C
Abstract: Ethylammonium nitrate confined between polar glass plates diffuses faster by a factor of 2 as compared to bulk values.
Publisher: American Chemical Society (ACS)
Date: 13-06-2011
DOI: 10.1021/LA201121P
Abstract: A range of surfaces coated with spherical silica particles, covering the size range from nanometer to micrometer, have been produced using Langmuir-Blodgett (LB) deposition. The particles were characterized both in suspension and in the Langmuir trough to optimize the surface preparation procedure. By limiting the particle aggregation and surface layer failures during the preparation steps, well-defined monolayers with a close-packed structure have been obtained for all particle sizes. Thus, this procedure led to structured surfaces with a characteristic variation in the litude and spatial roughness parameters. In order to obtain robust surfaces, a sintering protocol and an AFM-based wear test to determine the stability of the deposited surface layer were employed. Hydrophobization of the LB films followed by water contact angle measurements showed, for all tested particle sizes, the same increase in contact angle compared to the contact angle of a flat hydrophobic surface. This indicates nearly hexagonal packing and gives evidence for nearly complete surface wetting of the surface features.
Publisher: American Chemical Society (ACS)
Date: 17-11-2014
DOI: 10.1021/JZ5021422
Abstract: The remarkable physical properties of ionic liquids (ILs) make them potentially excellent lubricants. One of the challenges for using ILs as lubricants is their high cost. In this article, atomic force microscopy (AFM) nanotribology measurements reveal that a 1 mol % solution of IL dissolved in an oil lubricates the silica surface as effectively as the pure IL. The adsorption isotherm shows that the IL surface excess need only be approximately half of the saturation value to prevent surface contact and effectively lubricate the sliding surfaces. Using ILs in this way makes them viable for large-scale applications.
Publisher: American Chemical Society (ACS)
Date: 23-01-2002
DOI: 10.1021/LA015573J
Publisher: American Chemical Society (ACS)
Date: 04-2004
DOI: 10.1021/JP0374197
Publisher: American Chemical Society (ACS)
Date: 11-02-2021
Publisher: Informa UK Limited
Date: 12-2003
DOI: 10.1080/08927010310001618571
Abstract: The role of saliva in the oral cavity is manifold an important function is to serve as lubricant between hard (enamel) and soft (mucosal) tissues. Intraoral lubrication is of crucial importance in order to maintain functions such as deglutition, mastication and the faculty of speech. A large number of people suffer from impaired salivary functions, displaying symptoms such as 'dry mouth'. This results in a need for methods to assess the lubricating properties of both native saliva and potential artificial saliva formulations. Here, normal as well as lateral forces, acting between adsorbed salivary films, have been measured for the first time by means of colloidal probe atomic force microscopy (AFM). It was found that the presence of salivary pellicles between hard surfaces reduces the friction coefficient by a factor of 20. This reduction of friction is consistent with the long-range purely repulsive nature of the normal forces acting between the salivary films. The lubricating mechanism is presumably based on a full separation of the sliding surfaces by the salivary films. The friction between salivary films has been investigated at normal loads that cover the clinical jaw closing forces, and it can be concluded that the lubricating properties are maintained within this load interval. The present study indicates the usefulness of colloidal probe AFM, which offers a direct and quantitative measure of lubrication at a molecular level, in the study of biotribological phenomena. In particular, the results obtained here may have implications for the development of saliva substitutes.
Publisher: American Chemical Society (ACS)
Date: 22-01-2005
DOI: 10.1021/LA047763A
Abstract: Forces have been measured between silica surfaces with adsorbed surfactants by means of a bimorph surface force apparatus. The surfactants used are the cationic surfactant tetradecyltrimethylammonium bromide (TTAB) and the nonionic surfactant hexakis(ethylene glycol) mono-n-tetradecyl ether (C(14)E(6)) as well as mixtures of these two surfactants. The measurements were made at elevated pH, and the effect of salt was studied. At high pH the glass surface is highly charged, which increases the adsorption of TTAB. Despite the low adsorption generally seen for nonionic surfactants on silica at high pH, addition of C(14)E(6) has a considerable effect on the surface forces between two glass surfaces in a TTAB solution. The barrier force is hardly affected, but the adhesion is reduced remarkably. Also, addition of salt decreases the adhesion, but increases the barrier force. In the presence of salt, addition of C(14)E(6) also increases the thickness of the adsorbed layer. The force barrier height is also shown to be related to literature values for surface pressure data in these systems.
Publisher: American Chemical Society (ACS)
Date: 16-02-2008
DOI: 10.1021/LA7036907
Abstract: Using colloid probe atomic force microscopy, we show that if repulsive van der Waals forces exist between two surfaces prior to their contact then friction is essentially precluded and supersliding is achieved. The friction measurements presented here are of the same order as the lowest ever recorded friction coefficients in liquid, though they are achieved by a completely different approach. A gold sphere attached to an AFM cantilever is forced to interact with a smooth Teflon surface (templated on mica). In cyclohexane, a repulsive van der Waals force is observed that erges at short separations. The friction coefficient associated with this system is on the order of 0.0003. When the refractive index of the liquid is changed, the force can be tuned from repulsive to attractive and adhesive. The friction coefficient increases as the Hamaker constant becomes more positive and the ergent repulsive force, which prevents solid-solid contact, gets switched off.
Publisher: PeerJ
Date: 15-08-2023
DOI: 10.7717/PEERJ.15842
Publisher: American Chemical Society (ACS)
Date: 21-08-2001
DOI: 10.1021/LA010330C
Publisher: Wiley
Date: 05-07-1993
Publisher: American Chemical Society (ACS)
Date: 09-12-2007
DOI: 10.1021/JP063912H
Publisher: American Chemical Society (ACS)
Date: 16-09-2009
DOI: 10.1021/AM900381T
Abstract: The efficiency of poly(ε-caprolactone) (PCL) as a matrix polymer for cellulose nanocomposites has been investigated at the macromolecular contact level using atomic force microscopy in a colloidal probe configuration. Model cellulose microspheres grafted with PCL were prepared via ring-opening polymerization. Force measurements between the functionalized particles revealed the adhesion to be highly dependent on the contact time because of a diffusion-controlled mechanism. Moreover, an increase of the temperature to 60 degrees C (close to T(m) for the PCL graft) greatly enhanced the adhesion at the polymer-polymer interface, demonstrating the importance of entanglements in the annealing of composite materials.
Publisher: AIP Publishing
Date: 07-2014
DOI: 10.1063/1.4890335
Publisher: Royal Society of Chemistry (RSC)
Date: 2012
DOI: 10.1039/C2CP23694J
Abstract: The nanostructure of the ethanolammonium nitrate (EtAN)-air surface has been investigated using X-ray reflectometry (XRR), vibrational sum frequency spectroscopy (VSFS) and neutral impact collision ion scattering spectroscopy (NICISS). The XRR data decays more rapidly than expected for a perfectly sharp interface, indicating a diffuse electron (scattering length) density profile. Modelling of the XRR data using three different fitting routines produced consistent interfacial profiles that suggest the formation of interfacial EtAN clusters. Consistent with this, VSFS reveals that the EtAN surface is predominantly covered by -CH(2)- moieties, with the -NH(3)(+) and -OH groups of the cation buried slightly deeper in the interface. The elemental profiles determined using NICISS also show enrichment of carbon relative to nitrogen and oxygen in the outermost surface layer, which is consistent with the surface cation orientation deduced from VSFS, and with the presence of EtAN aggregates at the liquid surface.
Publisher: American Chemical Society (ACS)
Date: 07-09-2005
DOI: 10.1021/LA050825S
Abstract: The atomic force microscope, together with the colloid probe technique, has become a very useful instrument to measure interaction forces between two surfaces. Its potential has been exploited in this work to study the interaction between protein (apoferritin) layers adsorbed on silica surfaces and to analyze the effect of the medium conditions (pH, salt concentration, salt type) on such interactions. It has been observed that the interaction at low salt concentrations is dominated by electrical double layer (at large distances) and steric forces (at short distances), the latter being due to compression of the protein layers. The DLVO theory fits these experimental data quite well. However, a non-DLVO repulsive interaction, prior to contact of the protein layers, is observed at high salt concentration above the isoelectric point of the protein. This behavior could be explained if the presence of hydration forces in the system is assumed. The inclusion of a hydration term in the DLVO theory (extended DLVO theory) gives rise to a better agreement between the theoretical fits and the experimental results. These results seem to suggest that the hydration forces play a very important role in the stability of the proteins in the physiological media.
Publisher: Elsevier BV
Date: 07-1989
Publisher: Springer Science and Business Media LLC
Date: 05-12-2022
DOI: 10.1038/S41467-022-33407-5
Abstract: Although machine learning (ML) has shown promise across disciplines, out-of-s le generalizability is concerning. This is currently addressed by sharing multi-site data, but such centralization is challenging/infeasible to scale due to various limitations. Federated ML (FL) provides an alternative paradigm for accurate and generalizable ML, by only sharing numerical model updates. Here we present the largest FL study to-date, involving data from 71 sites across 6 continents, to generate an automatic tumor boundary detector for the rare disease of glioblastoma, reporting the largest such dataset in the literature ( n = 6, 314). We demonstrate a 33% delineation improvement for the surgically targetable tumor, and 23% for the complete tumor extent, over a publicly trained model. We anticipate our study to: 1) enable more healthcare studies informed by large erse data, ensuring meaningful results for rare diseases and underrepresented populations, 2) facilitate further analyses for glioblastoma by releasing our consensus model, and 3) demonstrate the FL effectiveness at such scale and task-complexity as a paradigm shift for multi-site collaborations, alleviating the need for data-sharing.
Publisher: Elsevier BV
Date: 02-2016
DOI: 10.1016/J.JMBBM.2015.09.014
Abstract: The mechanical resistance of the stratum corneum, the outermost layer of skin, to deformation has been evaluated at different length scales using Atomic Force Microscopy. Nanomechanical surface mapping was first conducted using a sharp silicon tip and revealed that Young׳s modulus of the stratum corneum varied over the surface with a mean value of about 0.4GPa. Force indentation measurements showed permanent deformation of the skin surface only at high applied loads (above 4µN). The latter effect was further demonstrated using nanomechanical imaging in which the obtained depth profiles clearly illustrate the effects of increased normal force on the elastic lastic surface deformation. Force measurements utilizing the single hair fiber probe supported the nanoindentation results of the stratum corneum being highly elastic at the nanoscale, but revealed that the lateral scale of the deformation determines the effective elastic modulus.This result resolves the fact that the reported values in the literature vary greatly and will help to understand the biophysics of the interaction of razor cut hairs that curl back during growth and interact with the skin.
Publisher: Elsevier BV
Date: 05-2015
DOI: 10.1016/J.IJPHARM.2015.03.049
Abstract: Tablets are the most convenient form for drug administration. However, despite the ease of manufacturing problems such as powder adhesion occur during the production process. This study presents surface and structural characterization of tablets formulated with commonly used excipients (microcrystalline cellulose (MCC), lactose, mannitol, magnesium (Mg) stearate) pressed under different compaction conditions. Tablet surface analyses were performed with scanning electron microscopy (SEM), profilometry and atomic force microscopy (AFM). The mechanical properties of the tablets were evaluated with a tablet hardness test. Local adhesion detected by AFM decreased when Mg stearate was present in the formulation. Moreover, the tablet strength of plastically deformable excipients such as MCC was significantly decreased after addition of Mg stearate. Combined these facts indicate that Mg stearate affects the particle-particle bonding and thus elastic recovery. The MCC excipient also displayed the highest hardness which is characteristic for a highly cohesive material. This is discussed in the view of the relatively high adhesion found between MCC and a hydrophilic probe at the nanoscale using AFM. In contrast, the tablet strength of brittle materials like lactose and mannitol is unaffected by Mg stearate. Thus fracture occurs within the excipient particles and not at particle boundaries, creating new surfaces not previously exposed to Mg stearate. Such uncoated surfaces may well promote adhesive interactions with tools during manufacture.
No related grants have been discovered for Mark Rutland.