ORCID Profile
0000-0001-6960-0491
Current Organisations
University of Western Australia
,
Ocean University of China
,
Tongji University
Does something not look right? The information on this page has been harvested from data sources that may not be up to date. We continue to work with information providers to improve coverage and quality. To report an issue, use the Feedback Form.
Publisher: American Society of Civil Engineers (ASCE)
Date: 12-2015
Publisher: American Society of Civil Engineers (ASCE)
Date: 03-2018
Publisher: American Society of Civil Engineers (ASCE)
Date: 2022
Publisher: American Society of Civil Engineers (ASCE)
Date: 07-2014
Publisher: Elsevier BV
Date: 04-2015
Publisher: Elsevier BV
Date: 09-2019
Publisher: Thomas Telford Ltd.
Date: 17-03-2017
Publisher: Thomas Telford Ltd.
Date: 02-2015
Abstract: Spudcan foundations of various geometries are commonly used in the field for supporting offshore oil and gas drilling (jack-up) rigs. This paper investigates the effect of the spudcan and its base geometry on the penetration and extraction resistance in soft normally and lightly overconsolidated clay. A series of centrifuge tests was undertaken on model spudcans of three different geometries typically used in the field. The spudcans were extracted from penetrations of 2·64∼3 (area equivalent) diameters and after an operation period of ∼19 months. Additional large-deformation finite-element analyses allowed for exploring a range of spudcan base geometries. Corresponding field data were accumulated. The results from this study have confirmed the accuracy of the assumption of a circular conical-based footing and the use of area equivalent diameter for assessing spudcan penetration resistance, as suggested by ISO guidelines 19905-1. Simulation of a flat-based circular plate resulted in 19% higher resistance compared to that of conical-based footings. For spudcans with cutouts and with a peripheral skirt, maximum penetration resistances were, respectively, 14 and 12% lower, and maximum extraction resistances were 20 and 14% lower compared to those for a general spudcan. The corresponding required jack-up leg length was 9 and 7% higher. The effect of peripheral skirt length was shown to be minimal (at least for length relative to spudcan diameter ≤ 0·42).
Publisher: Canadian Science Publishing
Date: 12-2016
Abstract: Spudcan punch-through during installation and preloading process is one of the key concerns for the jack-up industry. This incident occurs in layered deposits, with new design approaches for spudcan penetration in sand-over-clay deposits reported recently. This paper reports a novel design approach for spudcan penetration in stiff-over-soft clay deposits. Large-deformation finite element (LDFE) analyses were carried out using the Coupled Eulerian–Lagrangian (CEL) approach. The clay was modelled using the extended elastic – perfectly plastic Tresca soil model allowing strain softening and rate dependency of the undrained shear strength. A detailed parametric study was undertaken, varying the strength ratio between bottom and top soil layers, the thickness of the top layer relative to the spudcan diameter, and degree of nonhomogeneity of the bottom layer. Existing data from centrifuge model tests were first used to validate the LDFE results, and then the measured and computed datasets were used to develop the formulas in the proposed design approach. The approach accounts for the soil plug in the bottom layer, and the corresponding additional resistance. Where there is the potential for punch-through, the approach provides estimations of the depth and bearing capacity at punch-through, the bearing capacity at the stiff–soft layer interface, and the bearing capacity in the bottom layer. Comparison shows that the punch-through method suggested in ISO standard 19905-1 provides a conservative estimate of the bearing capacity at punch-through, with guidelines provided to improve the method.
Publisher: MDPI AG
Date: 24-06-2021
DOI: 10.3390/JMSE9070689
Abstract: Clay–sand–clay deposits are commonly encountered in the offshore field. For spudcan installation in this soil stratigraphy, the potential for punch-through exists, with the peak penetration resistance formed within the interbedded sand layer. Therefore, a careful assessment of the penetration resistance profile has to be performed. Based on the recently proposed failure-stress-dependent model, this paper presents a modified predictive model for estimating the peak resistance. The modified model incorporates the bearing capacity depth factor and the protruded soil plug in the bottom clay layer into the formulation. It is proven that the modified predictive model provides improved deterministic estimations for the peak resistances measured in centrifuge tests. Based on the modified predictive model, a parameter optimization technique is utilized to optimize the prediction of peak resistance using penetration resistances observed beforehand. A detailed application procedure is proposed and applied to the centrifuge tests accumulated from existing publications, with further improvement on the predictions demonstrated. The proposed parameter optimization procedure combined with the modified predictive model provides an approach to perform real-time optimization for assessing spudcan peak resistance in clay–sand–clay deposits.
Publisher: Springer International Publishing
Date: 2018
Publisher: Hindawi Limited
Date: 2018
DOI: 10.1155/2018/4312494
Abstract: This paper focuses on the mechanical behavior and damage evolution of Huashan granite subjected to cyclic loading. Four levels of confining pressure (0, 15, 25, and 35 MPa) were applied during cyclic axial loading by using a Rock Test System (MTS815) along with an acoustic emission (AE) monitoring device. Experimental results indicate that the number of AE activities is higher under cyclic triaxial loading compared to that under cyclic uniaxial loading. The measured stress-strain curves of both uniaxial and triaxial tests under cyclic loading are concave-up, but the degree of concavity is mild for the latter. As the cycle number rises, elastic modulus of the granite s le under different confining pressures increases. The slope of the peak strength versus confining pressure plot for the cyclic loading is larger than that for the monotonic loading. Besides, it is found that the dissipated energy increases with the increase of cyclic stress, but it hardly increases in proportion with the confining pressure. The damage parameters defined in terms of the plastic strain can be extended for the whole cyclic loading process, and they agree well with the energy-based damage parameters.
Publisher: American Society of Civil Engineers (ASCE)
Date: 04-2015
Publisher: Elsevier BV
Date: 03-2023
No related grants have been discovered for Jingbin Zheng.