Jun Wang

Cutting Forces and Tool Wear in Dry Milling of Ti6Al4V

Publisher: Trans Tech Publications, Ltd.

Date: 09-2012

DOI: 10.4028/WWW.SCIENTIFIC.NET/AMR.565.454

Abstract: Titanium alloys are difficult-to-cut materials. This paper presents an experimental study of the effects of different cutting conditions and tool wear on cutting forces in dry milling Ti6Al4V with coated carbide inserts. The experimental results show that the peak forces increase with the increase in the feed rate and depth of cut. With the cutting speed increment in the range from 50 m/min to 150 m/min the peak forces decrease, while at further higher cutting speeds investigated peak forces increase. The decrease of the peak forces is due to thermal softening of the workpiece material and the increase is because of the strain hardening rate of Ti6Al4V. The tool wear experiment reveals that the major tool wear mechanism is the flank wear. The variations of the peak forces are caused by both the tool wear propagation and the thermal effects.

An efficient framework to exploit frequency diversity in OFDM: Precoding with adaptive subcarrier selection

Publisher: IEEE

Date: 09-2006

DOI: 10.1109/PIMRC.2006.254299

Impact characteristics and stagnation formation on a solid surface by a supersonic abrasive waterjet

Publisher: IOP Publishing

Date: 12-2019

DOI: 10.1088/2631-7990/AB531C

Abstract: A computational fluid dynamics (CFD) study of the impact characteristics and stagnation formation on a solid target surface by an abrasive waterjet at supersonic velocities is presented to understand the impact process. A CFD model is developed and verified by experimental water and particle velocities and then used to simulate the jet impact process. The trends of the stagnation formation and its effect on the jet flow with respect to the jetting and impacting parameters are ly discussed. It is found that stagnation formation at the impact site increases with an increase in the impact time, nozzle standoff distance and nozzle diameter, while the initial peak velocity at the nozzle exit has little effect on the size of the stagnation zone. It is shown that stagnation markedly changes the water and particle flow direction, so that the particle impact angle is varied and the jet impact area is enlarged. The jet structure may be classified to have a free jet flow region, a jet deflection region with a stagnation zone and a wall jet region. Furthermore, the stagnation affects significantly the waterjet and particle energy transferred to the target surface. The average particle velocity across the jet is reduced by approximately one third due to the d ing effect of the stagnation under the conditions considered in this study.

Characterisation of the Femtosecond Laser Micro-Grooving Process for Germanium Substrates

Publisher: Trans Tech Publications, Ltd.

Date: 10-2016

DOI: 10.4028/WWW.SCIENTIFIC.NET/MSF.874.291

Abstract: An experimental study is reported to characterise the femtosecond (FS) laser grooving process for Germanium (Ge) substrates. The effects of process parameters, including laser fluence, pulse repetition rate and scan speed, on the groove characteristics, material removal rate (MRR) and heat affected zone (HAZ) size are discussed. It is shown that with properly selected process parameters, high quality micro-grooves can be obtained on Ge wafers. Recommendations are finally made on the selection of the most appropriate process parameters for FS micro-grooving of Ge substrates.

Material removal of single crystal 4H-SiC wafers in hybrid laser-waterjet micromachining process

Publisher: Elsevier BV

Date: 08-2018

DOI: 10.1016/J.MSSP.2018.03.035

An intelligent chatter detection method based on EEMD and feature selection with multi-channel vibration signals

Publisher: Elsevier BV

Date: 10-2018

DOI: 10.1016/J.MEASUREMENT.2018.06.006

Surface quality evaluation of single crystal 4H-SiC wafer machined by hybrid laser-waterjet: Comparing with laser machining

Publisher: Elsevier BV

Date: 04-2019

DOI: 10.1016/J.MSSP.2018.12.037

A cutting forces model for milling Inconel 718 alloy based on a material constitutive law

Publisher: SAGE Publications

Date: 30-11-2012

DOI: 10.1177/0954406212469167

Abstract: This article presents a cutting force model for the milling of Inconel 718 whose machinability is considered to be very poor. The Johnson–Cook constitutive material model is used to determine the flow stress of Inconel 718 while the shear angle is determined based on a shear plane model assuming that the total energy on the shear plane plus the energy on the rake face is minimum. The temperature in the machining region is determined by using an iterative process. Finally, the cutting forces on each tooth of the milling cutter are calculated from its chip load considering the oblique cutting effects. The model is then verified by comparing the model predictions with the experimental data under the corresponding conditions, which shows a relatively good agreement with an average percentage error of 10.5% along the feed and normal directions.

Predictive models for the geometrical characteristics of channels milled by abrasive waterjet

Publisher: IEEE

Date: 08-2015

DOI: 10.1109/COASE.2015.7294305

Mechanisms and predictive force models for machining with rake face textured cutting tools under orthogonal cutting conditions

Publisher: Elsevier BV

Date: 04-2021

DOI: 10.1016/J.IJMECSCI.2020.106246

An experimental study of abrasive waterjet machining of Ti-6Al-4V

Publisher: Springer Science and Business Media LLC

Date: 07-05-2015

DOI: 10.1007/S00170-015-7245-5

Machining of Micro-Channels on Brittle Glass Using an Abrasive Slurry Jet

Publisher: Trans Tech Publications, Ltd.

Date: 06-2010

DOI: 10.4028/WWW.SCIENTIFIC.NET/KEM.443.639

Abstract: This paper presents a study of using an abrasive slurry jet for the machining of micro channels on brittle glasses. The machined surface morphology and channel dimensions are used to assess the technology. Surface morphology was found featuring with two types of wave patterns one was along the channels with large wave lengths as a result of the jet deflection during the motion of nozzle, and the other was due to viscous flow that resulted in smooth surface eroded predominantly by ductile mode. The investigation showed that using higher jet pressure and higher particle concentration enables to create channels with higher depth, although these widened the channels and degraded the surface quality in some cases by inducing a larger number of pit fragments on the surface. With proper control of the operating parameters, this technology can be used for machining micro channels on brittle materials with high quality of surface finish.

Experimental Study of Cutting Forces in Micro End-Milling

Publisher: Trans Tech Publications, Ltd.

Date: 04-2012

DOI: 10.4028/WWW.SCIENTIFIC.NET/AMR.500.357

Abstract: Micro-end-milling is an efficient and economical manufacturing operation that is capable of accurately producing high aspect ratio features and parts. It is important to study the cutting forces in micro-milling for the planning and control of the process. This paper presents an experimental study of the cutting forces in micro-end-milling of a 6160 aluminum alloy. The measured cutting forces are presented and discussed for different cutting conditions, such as various feeds per tooth, cutter diameters, and cutting speeds. It is found that the peak cutting forces increase with increasing cutting speed and feed rate. The effects of tool runout on the cutting forces were also analyzed based on the experimental results, from which the influences of feed rate and cutting speed are found to be obvious.

On DEM-CFD study of the dynamic characteristics of high speed micro-abrasive air jet

Publisher: Elsevier BV

Date: 11-2014

DOI: 10.1016/J.POWTEC.2014.07.018

Assessment of cutting forces in high-speed milling of Inconel 718 considering the dynamic effects

Publisher: SAGE Publications

Date: 10-06-2013

DOI: 10.1177/0954405413489968

Abstract: Aerospace material Inconel 718 is well known for its poor machinability. This article presents an experimental study of the cutting forces in high-speed dry milling of Inconel 718 using a milling cutter with coated carbide inserts. An assessment of the cutting force variations is conducted using statistical approaches and wavelet decomposition taking into consideration the dynamic effects. The averaged peak force values, the peak force variation range and distribution, and the skewness are evaluated. It shows that cutting speed does not have a significant influence on the averaged peak cutting force for the range tested. The tool–workpiece vibrations at the cutter entry stage and exit stage are generally more significant. Moreover, wavelet packet decomposition at level 3 with the DB4 wavelet and Shannon entropy is found to be an effective approach to identify the chatter onset.

Modelling the cutting forces in micro-end-milling using a hybrid approach

Publisher: Springer Science and Business Media LLC

Date: 27-05-2014

DOI: 10.1007/S00170-014-5953-X

Temperature evolution and material removal mechanisms in nanosecond-pulsed laser ablation of polycrystalline diamond

Publisher: SAGE Publications

Date: 20-06-2014

DOI: 10.1177/0954405414535773

Abstract: A study of the single-pulsed laser ablation process for a polycrystalline diamond is presented. A simulation of the laser ablation process using a finite element model is carried out to understand the temperature evolution, material removal process and mechanisms, as well as the other physical phenomena associated with this process, that is, carbon phase transformation, liquid-phase ejection and vapour lasma shielding effect. It is found that mass material removal can be achieved through surface evaporation under a higher laser pulse energy. It is further found that diamond graphitization under laser irradiation is responsible for heat losses due to the large heat accumulation in the graphitized diamond, while cobalt melting suppresses the evaporation of cobalt phase because of the heat consumption for solid–liquid transition. Crater depth and surface formation are also investigated experimentally on the polycrystalline diamond using single-pulsed laser ablation. The predicted crater depths are in reasonably good agreement with the corresponding experimental results.

Modelling of the micro-channelling process on glasses using an abrasive slurry jet

Publisher: Elsevier BV

Date: 02-2012

DOI: 10.1016/J.IJMACHTOOLS.2011.10.005

The wear mechanisms of reaction bonded silicon carbide under abrasive polishing and slurry jet impact conditions

Publisher: Elsevier BV

Date: 09-2018

DOI: 10.1016/J.WEAR.2018.06.001

An investigation of surface roughness in micro-end-milling of metals

Publisher: Informa UK Limited

Date: 26-07-2016

DOI: 10.1080/14484846.2016.1211472

On the erosion process on quartz crystals by the impact of multiple high-velocity micro-particles

Publisher: Elsevier BV

Date: 03-2016

DOI: 10.1016/J.TRIBOINT.2015.12.003

An analytical model for the prediction of temperature distribution and evolution in hybrid laser-waterjet micro-machining

Publisher: Elsevier BV

Date: 2017

DOI: 10.1016/J.PRECISIONENG.2016.07.002

Strip formation mechanisms and characteristics models in 3D printing of viscous polymer inks

Publisher: Elsevier BV

Date: 09-2021

DOI: 10.1016/J.JMAPRO.2021.08.009

Mechanisms of channel formation on glasses by abrasive waterjet milling

Publisher: Elsevier BV

Date: 07-2012

DOI: 10.1016/J.WEAR.2012.06.008

A Study of Cutting Forces in High-Speed Dry Milling of Inconel 718

Publisher: Trans Tech Publications, Ltd.

Date: 04-2012

DOI: 10.4028/WWW.SCIENTIFIC.NET/AMR.500.105

Abstract: nconel 718 is one of the most commercially important superalloys but with very poor machinability. It has a very high yield stress and a high tendency to adhesion and work-hardening. A recent trend of improving the machining processes of difficult-to-cut materials is to move towards dry cutting operations. This paper presents an experimental study of the cutting forces in high speed dry milling of Inconel 718 using a milling cutter with coated carbide inserts. It is found that the peak cutting forces increase with an increase in chip load in a nonlinear way, but cutting speed does not show a significant influence on the cutting force for the range of cutting speeds tested in this study.

10.4028/0-87849-364-6.375

Publisher: Trans Tech Publications Ltd.

Date: 2005

DOI: 10.4028/0-87849-364-6.375

Microgrooving of Germanium Wafers Using Laser and Hybrid Laser-Waterjet Technologies

Publisher: Trans Tech Publications, Ltd.

Date: 09-2014

DOI: 10.4028/WWW.SCIENTIFIC.NET/AMR.1017.193

Abstract: Lasers have the potential for the micromachining of germanium (Ge). However, the thermal damages associated with the laser machining process need to be properly controlled. To minimize the thermal damages, a hybrid laser-waterjet ablation technology has recently been developed for micromachining. This paper presents an experimental study to assess the machining performances in microgrooving of Ge by using a nanosecond laser and the hybrid laser-waterjet technology. The effects of laser pulse energy, pulse overlap and focal plane position on the groove geometry and heat affected zone (HAZ) size are analyzed and discussed. It is shown that the hybrid laser-waterjet technology can give rise to narrow and deep microgrooves with minimum HAZ.

A study of abrasive waterjet characteristics by CFD simulation

Publisher: Elsevier BV

Date: 11-2004

DOI: 10.1016/J.JMATPROTEC.2004.04.037

Study of Abrasive Jet Micromachining for Brittle Materials

Publisher: American Scientific Publishers

Date: 15-06-2012

DOI: 10.1166/ASL.2012.2772

A study of delamination on graphite/epoxy composites in abrasive waterjet machining

Publisher: Elsevier BV

Date: 06-2008

DOI: 10.1016/J.COMPOSITESA.2008.04.001

Mechanisms of enhancing the machining performance in micro abrasive waterjet drilling of hard and brittle materials by vibration assistance

Publisher: Elsevier BV

Date: 04-2020

DOI: 10.1016/J.IJMACHTOOLS.2020.103528

Laser–material interaction and grooving performance in ultrafast laser ablation of crystalline germanium under ambient conditions

Publisher: SAGE Publications

Date: 15-07-2013

DOI: 10.1177/0954405413492322

Abstract: Microgrooving on crystalline germanium (Ge) surface using 1064 nm wavelength ultrafast laser pulses under ambient condition is investigated. The interaction of laser and target material and the influence of processing parameters such as laser power, pulse repetition rate and scan speed on the groove dimensions and surface roughness are studied. For the laser radiation fluence range used (0.4–0.8 J/cm 2 ), material removal is primarily controlled by optical penetration depth. The depth and width of grooves increase with laser power. In multipulse irradiation, heat accumulation due to residual thermal energy from successive laser pulses results in a greater material removal. Furthermore, groove depth and width decrease as the pulse repetition rate increases from 0.5 to 2 MHz, due to the decrease in pulse energy with an increase in repetition rate causing ablation threshold fluence to move towards the central portion of the Gaussian pulse. Surface roughness has not shown significant changes for the parameters used in this study. A micro-Raman analysis of groove surfaces reveals a change in the crystallinity of the Ge due to laser irradiation.

Evolution of micro/nano-structural arrays on crystalline silicon carbide by femtosecond laser ablation

Publisher: Elsevier BV

Date: 2021

DOI: 10.1016/J.MSSP.2020.105299

Mechanisms of microhole formation on glasses by an abrasive slurry jet

Publisher: AIP Publishing

Date: 15-02-2009

DOI: 10.1063/1.3079802

Abstract: Abrasive jet micromachining is considered as a promising precision processing technology for brittle materials such as silicon substrates and glasses that are increasingly used in various applications. In this paper, the mechanisms of microhole formation on brittle glasses by an abrasive slurry jet are studied based on the viscous flow and erosion theories. It is shown that the hole cross section is characterized by a “W” shape and can be classified into three zones caused, respectively, by jet direct impact, viscous flow, and turbulent flow induced erosion. An analysis of the surface morphology shows that ductile-mode erosion is dominant. The effect of process parameters on material removal is studied which shows that increasing the pressure and erosion time increases the hole depth, but has little effect on the hole diameter.

An investigation of recast behavior in laser ablation of 4H-silicon carbide wafer

Publisher: Elsevier BV

Date: 2020

DOI: 10.1016/J.MSSP.2019.104701

Controlled Fabrication of Micro/Nano-Structures on Germanium Using Ultrashort Laser Pulses under Ambient Conditions

Publisher: Trans Tech Publications, Ltd.

Date: 2016

DOI: 10.4028/WWW.SCIENTIFIC.NET/AMR.1136.440

Abstract: A technique for ordered fabrication of periodic freestanding micro/nanostructures on the crystalline germanium (Ge) surfaces with 1064 nm wavelength ultrashort laser pulses under ambient conditions is presented. The laser radiation fluence used for obtaining the structures is close to the melting threshold (0.1 J/cm 2 ) of Ge. The dimensions of structures range from hundreds of nanometres to a few microns. The orientation of the periodic surface structures depends on laser beam polarization direction. Arrays of structures are formed in rows parallel to the s le movement direction for s les machined with s-polarized laser pulses, but formed in the direction perpendicular to the movement for p-polarized pulses. The structures are fabricated under variable temperatures on s le surface owing to the changed interference between incident and reflected laser beams. A micro-Raman analysis of the processed surfaces shows a minor change in the spectral intensity as compared to the unprocessed surface and the material retains its crystallinity after laser irradiation.

An investigation of the hole machining processes on woven carbon-fiber reinforced polymers (CFRPs) using abrasive waterjets

Publisher: Informa UK Limited

Date: 17-05-2018

DOI: 10.1080/10910344.2018.1449217

Kerf formation analysis in the abrasive waterjet cutting of industrial ceramics

Publisher: Elsevier BV

Date: 10-2002

DOI: 10.1016/S0924-0136(02)00437-5

An Experimental Study of the Effect of Cutting Parameters on Micro Milling Process

Publisher: Trans Tech Publications, Ltd.

Date: 09-2012

DOI: 10.4028/WWW.SCIENTIFIC.NET/AMR.565.558

Abstract: In micro milling, cutting parameters such as feed per tooth and cutting speed are found to have significant influence on cutting forces and surface quality. To address these issues, an experimental study of micro milling with three types of metal material (steel, brass and aluminium alloy) is conducted. The experiment setup and cutting conditions are described the experiment results are presented with a discussion of the influence of various cutting parameters such as feed per tooth and tool diameter. These results are used to provide strategies to optimise cutting parameters and achieve better surface quality with the concern of tool diameter and material hardness when micro milling selected materials.

Enhancing the machining performance by cutting tool surface modifications: a focused review

Publisher: Informa UK Limited

Date: 27-03-2019

DOI: 10.1080/10910344.2019.1575412

Analytical modelling of cutting forces in near-orthogonal cutting of titanium alloy Ti6Al4V

Publisher: SAGE Publications

Date: 10-07-2014

DOI: 10.1177/0954406214542967

Abstract: Titanium and its alloys are difficult to machine due to their high chemical reactivity with tool materials and low thermal conductivity. Chip segmentation caused by the thermoplastic instability is always observed in titanium machining processes, which leads to varied cutting forces and chip thickness, etc. This paper presents an analytical modelling approach for cutting forces in near-orthogonal cutting of titanium alloy Ti6Al4V. The catastrophic shear instability in the primary shear plane is assumed as a semi-static process. An analytical approach is used to evaluate chip thicknesses and forces in the near-orthogonal cutting process. The shear flow stress of the material is modelled by using the Johnson–Cook constitutive material law where the strain hardening, strain rate sensitivity and thermal softening behaviours are coupled. The thermal equations with non-uniform heat partitions along the tool–chip interface are solved by a finite difference method. The model prediction is verified with experimental data, where a good agreement in terms of the average cutting forces and chip thickness is shown. A comparison of the predicted temperatures with published data obtained by using the finite element method is also presented.

A study of the micro-hole geometry evolution on glass by abrasive air-jet micromachining

Publisher: Elsevier BV

Date: 2018

DOI: 10.1016/J.JMAPRO.2017.11.013

Reliability of partial ambiguity fixing with multiple GNSS constellations

Publisher: Springer Science and Business Media LLC

Date: 12-06-2012

DOI: 10.1007/S00190-012-0573-4

Effect of liquid properties on the stability of an abrasive waterjet

Publisher: Elsevier BV

Date: 08-2008

DOI: 10.1016/J.IJMACHTOOLS.2008.01.009

Micromachining of 4H-SiC using femtosecond laser

Publisher: Elsevier BV

Date: 10-2018

DOI: 10.1016/J.CERAMINT.2018.06.245

Computed success rates of various carrier phase integer estimation solutions and their comparison with statistical success rates

Publisher: Springer Science and Business Media LLC

Date: 24-10-2010

DOI: 10.1007/S00190-010-0418-Y

Further Development of Oxley’s Predictive Force Model for Orthogonal Cutting

Publisher: Informa UK Limited

Date: 02-01-2015

DOI: 10.1080/10910344.2014.991026

A Comparison among Dry Laser Ablation and Some Different Water-Laser Co-Machining Processes of Single Crystal Silicon Carbide

Publisher: Trans Tech Publications, Ltd.

Date: 07-2016

DOI: 10.4028/WWW.SCIENTIFIC.NET/MSF.861.3

Abstract: Single crystal silicon carbide (SiC) is a new semiconductor material that has a great potential to be widely used. However, SiC is a kind of difficult-to-machine material due to its extreme hardness and brittleness. The present study investigated the machinability of single crystal SiC using dry laser and three different water-laser co-machining processes. The results indicate that using the hybrid laser-waterjet micro-machining to micro-groove single crystal SiC can derive the clean and straight edges and thermal damage-free grooves.

A STUDY OF MICRO-CHANNELING ON GLASSES USING AN ABRASIVE SLURRY JET

Publisher: Informa UK Limited

Date: 12-2012

DOI: 10.1080/10910344.2012.731947

Predictive modelling of cutting forces in end milling of titanium alloy Ti6Al4V

Publisher: SAGE Publications

Date: 11-10-2016

DOI: 10.1177/0954405416673108

Abstract: A cutting force model, based on a predictive model for orthogonal cutting, is developed for force predictions in end milling of titanium alloy Ti6Al4V. The model assumes a semi-stationary process for the serrated chip formation. The Johnson–Cook material model that couples strain hardening, strain rate sensitivity and thermal softening effects is applied to represent the material strength. A thermal model considering the tool thermal properties is integrated to account for the high temperature rise due to the low thermal conductivity of Ti6Al4V. To extend the predictive model to milling, the end mill is discretised into several axial slices, and an equivalent cutting edge is used to include the end cutting edge effect caused by the first axial slice. The model is assessed by comparing its prediction with the experimental results and a mechanistic model for verification. The results show that the proposed model outperforms the mechanistic model with higher accuracy in force prediction.

Mechanisms and predictive models for the erosion process of super hard and brittle materials by a vibration-assisted slurry jet

Publisher: Elsevier BV

Date: 12-2021

DOI: 10.1016/J.IJMECSCI.2021.106794

Detection and analysis of chatter occurrence in micro-milling process

Publisher: SAGE Publications

Date: 31-10-2014

DOI: 10.1177/0954405414522216

Abstract: An experimental study to understand the characteristics related to chatter occurrence in micro-milling operations is presented. Accelerometers are used to measure the vibration signals in the machining process. The acceleration signals are then analysed in the time domain and the frequency domain. Along with the onset of chatter, it is found that there is a characteristic shift of the dominant frequency components in addition to the change of vibration litude. A modulation of the spindle frequency around the chatter frequency is also found to be present in the vibration signal. A dimensionless chatter indicator based on revolution root-mean-square values is designed and used to evaluate the stability of the micro-milling process. It is shown that the proposed indicator provides a simple, but effective way to detect chatter onset.

Impact erosion by high velocity micro-particles on a quartz crystal

Publisher: Elsevier BV

Date: 02-2015

DOI: 10.1016/J.TRIBOINT.2014.10.016

Investigation and modelling of hybrid laser-waterjet micromachining of single crystal SiC wafers using response surface methodology

Publisher: Elsevier BV

Date: 09-2017

DOI: 10.1016/J.MSSP.2017.05.029

A study of the flow characteristics in micro-abrasive jets

Publisher: Elsevier BV

Date: 09-2011

DOI: 10.1016/J.EXPTHERMFLUSCI.2011.03.004

Spray Pyrolysis Technique for Fabrication of Nano-Sized Spherical Agglomerated Oxide Powders for Batteries

Publisher: Trans Tech Publications, Ltd.

Date: 04-2003

DOI: 10.4028/WWW.SCIENTIFIC.NET/JMNM.15-16.325

Process models for controlled-depth abrasive waterjet milling of amorphous glasses

Publisher: Springer Science and Business Media LLC

Date: 06-11-2014

DOI: 10.1007/S00170-014-6514-Z

Analysis and modelling of particle velocities in micro-abrasive air jet

Publisher: Elsevier BV

Date: 09-2009

DOI: 10.1016/J.IJMACHTOOLS.2009.05.012

Orthogonality defect and reduced search-space size for solving integer least-squares problems

Publisher: Springer Science and Business Media LLC

Date: 25-07-2012

DOI: 10.1007/S10291-012-0276-6

An Experimental Investigation of Cutting Forces in Micro End-Milling Process

Publisher: Trans Tech Publications, Ltd.

Date: 05-2016

DOI: 10.4028/WWW.SCIENTIFIC.NET/KEM.693.710

Abstract: This paper presents an experimental study of cutting forces during micro end-milling of brass. The influences of cutting speed and feed per tooth on cutting forces have been researched. The results show that the resultant force F r and feed force F x significantly increase with increasing the feed per tooth. The resultant force F r , feed force F x and normal force F y increase with increasing cutting speed. The specific shear energy is also investigated. It is observed that the specific shear energy increases greatly with decreasing the feed per tooth when the feed per tooth is less than minimum chip thickness.

Discovery Projects - Grant ID: DP110100690

Start Date: 2011

End Date: 12-2014

Amount: $380,000.00

Funder: Australian Research Council

Discovery Projects - Grant ID: DP210101645

Start Date: 2021

End Date: 2021

Amount: $395,000.00

Funder: Australian Research Council

Linkage Projects - Grant ID: LP0989304

Start Date: 06-2009

End Date: 06-2012

Amount: $351,000.00

Funder: Australian Research Council

Discovery Projects - Grant ID: DP110103150

Start Date: 2011

End Date: 12-2014

Amount: $210,000.00

Funder: Australian Research Council

Linkage - International - Grant ID: LX0242375

Start Date: 08-2002

End Date: 12-2006

Amount: $41,400.00

Funder: Australian Research Council

Discovery Projects - Grant ID: DP170100643

Start Date: 2017

End Date: 11-2020

Amount: $360,500.00

Funder: Australian Research Council

Discovery Projects - Grant ID: DP0663479

Start Date: 2006

End Date: 12-2009

Amount: $260,000.00

Funder: Australian Research Council

Discovery Projects - Grant ID: DP0451081

Start Date: 05-2004

End Date: 12-2007

Amount: $208,480.00

Funder: Australian Research Council

Discovery Projects - Grant ID: DP0878285

Start Date: 07-2008

End Date: 06-2012

Amount: $300,000.00

Funder: Australian Research Council

Discovery Projects - Grant ID: DP0342641

Start Date: 02-2003

End Date: 12-2006

Amount: $227,000.00

Funder: Australian Research Council

Discovery Projects - Grant ID: DP180103689

Start Date: 2018

End Date: 05-2021

Amount: $332,398.00

Funder: Australian Research Council

Linkage Projects - Grant ID: LP0667735

Start Date: 11-2006

End Date: 06-2011

Amount: $295,000.00

Funder: Australian Research Council

Research Networks - Grant ID: RN0458455

Start Date: 07-2004

End Date: 06-2009

Amount: $1,500,000.00

Funder: Australian Research Council

Linkage Infrastructure, Equipment And Facilities - Grant ID: LE0775643

Start Date: 07-2007

End Date: 07-2008

Amount: $380,000.00

Funder: Australian Research Council

Special Research Initiatives - Grant ID: SR0354722

Start Date: 02-2004

End Date: 12-2004

Amount: $20,000.00

Funder: Australian Research Council

Linkage Infrastructure, Equipment And Facilities - Grant ID: LE100100098

Start Date: 06-2010

End Date: 03-2012

Amount: $600,000.00

Funder: Australian Research Council