ORCID Profile
0000-0003-2610-891X
Current Organisation
UNSW Sydney
Does something not look right? The information on this page has been harvested from data sources that may not be up to date. We continue to work with information providers to improve coverage and quality. To report an issue, use the Feedback Form.
Publisher: Informa UK Limited
Date: 02-10-2015
Publisher: SAGE Publications
Date: 24-09-2019
Abstract: Knowledge of fibre strength is crucial for understanding the failure behaviour of fibre-reinforced composite materials and structures. Measuring the properties of technical fibres has been known to be very challenging, and the different challenges associated with single fibre characterisation are illustrated in this article. An improved and automated experimental methodology for tensile testing of single fibres is described. This process has been used to generate fibre strength data for T700 carbon fibres at three different gauge lengths of 4, 20 and 30 mm. The variability in strength and modulus of short fibres was found to be much larger than that of longer fibres. Statistical analysis of this large data set has also highlighted the limitations of the standard Weibull distribution for representing fibre strength behaviour. The need for a better statistical representation of the fibre strength data in order to provide a more accurate description of the fibre strength behaviour has been emphasized.
Publisher: MDPI AG
Date: 09-07-2019
DOI: 10.3390/JCS3030069
Abstract: Mechanical properties of fibre reinforced composites are primarily dependent on those of fibres. Fibre properties are used for estimating the damage and strength behaviour of composite materials and structures. Tensile strength of fibres is commonly determined by single fibre tensile tests, which is challenging and is prone to measurement errors. In this study, different possible sources of errors due to experimental limitations in the fibre testing process were identified. Their effect on fibre tensile strength was analytically modelled. This model was used to evaluate the uncertainty in experimentally determined fibre strength. A sensitivity analysis was conducted to rank the relative significance of input quantities on the calculated fibre strength. Since composite models require fibre properties determined at very small gauge lengths, the results of the sensitivity analysis were extrapolated to determine critical parameters for tests done at those small gauge lengths of a few millimetres. It was shown that, for sufficiently long fibres, their strength depends mainly on the diameter and failure force however, for shorter gauge lengths, the effects of misalignment become very significant. The knowledge of uncertainty would be useful in estimating the reliability of the predictions made by composite strength models on the damage and failure behaviour of composite materials and structures. Minimising the influence of critical parameters on fibre strength would help in designing improved single fibre testing systems capable of determining fibre strength more accurately.
Publisher: Research Square Platform LLC
Date: 15-11-2022
DOI: 10.21203/RS.3.RS-2220331/V1
Abstract: Automated fibre placement (AFP) is an advanced robotic manufacturing technique which can overcome the challenges of traditional composite manufacturing. The interlaminar strength of AFP-manufactured composites depends on the in-situ thermal history during manufacturing. The thermal history is controlled by the choice of processing conditions and improper interfacial temperatures may result in insufficient bonding. Being able to better predict such maintenance issues in real-time is an important focus of smart manufacturing and Industry 4.0 to improve manufacturing operations. This study focuses on developing a digital tool for process monitoring which integrates the physical and digital space of the AFP process. The digital tool constitutes a machine learning model to predict the in-situ thermal history during AFP manufacturing. The predicted thermal history can be compared with the real-time in-situ temperatures during manufacturing to predict the quality of the layup. A GUI application is developed to provide benchmarking data for comparison with real-time temperatures during manufacturing enabling monitoring and predictive maintenance of the AFP process paving way for the development of a digital twin of the AFP composites manufacturing process.
Publisher: Elsevier BV
Date: 07-2022
Publisher: SAGE Publications
Date: 20-09-2023
DOI: 10.1177/08927057221123477
Abstract: Many numerical models of the Automated Fibre Placement (AFP) manufacturing process have been developed to assist in the design process of composite components and structures. Although the tape placement process, in general is a 3-D transient process, limited models considering the 3-D nature of the process exist. This paper describes the development of a 3-D Finite Element (FE) model incorporating the effect of non-concentrated input heat flux distribution on adjacent paths. The model can predict an accurate thermal history of a thermoplastic composite laminate for a complete AFP deposition process. Composite laminates having plies made up of both a single tow and multiple tows have been simulated to study their thermal behaviour during the manufacturing process. Simulations have been conducted both with and without considering the input heat effect on adjacent tows for comparison. Temperatures were measured by embedding two different configurations of optical fibre Bragg grating (FBGs) sensors within the laminate during the lay-up process. This served a dual purpose of validating the model as well as the experimental methodology.
Publisher: Elsevier BV
Date: 04-2022
Publisher: Springer Science and Business Media LLC
Date: 05-05-2020
Publisher: Walter de Gruyter GmbH
Date: 04-2021
DOI: 10.1515/MT-2020-0058
Abstract: The test data for static burst strength and load cycle fatigue strength of pressure vessels can often be well described by Gaussian normal or Weibull distribution functions. There are various approaches which can be used to determine the parameters of the Weibull distribution function however, the performance of these methods is uncertain. In this study, six methods are evaluated by using the criterion of OSL (observed significance level) from Anderson-Darling (AD) goodness of Fit (GoF), These are: a) the norm-log based method, b) least squares regression, c) weighted least squares regression, d) a linear approach based on good linear unbiased estimators, e) maximum likelihood estimation and f) method of moments estimation. In addition, various approaches of ranking function are considered. The results show that there are no outperforming methods which can be identified clearly, primarily due to the limitation of the small s le size of the test data used for Weibull analysis. This randomness resulting from the s ling is further investigated by using Monte Carlo simulations, concluding that the s le size of the experimental data is more crucial than the exact method used to derive Weibull parameters. Finally, a recommendation is made to consider the uncertainties of the limitations due to the small size for pressure vessel testing and also for general material testing.
No related grants have been discovered for Faisal Islam.