ORCID Profile
0000-0003-1221-7445
Current Organisation
Nanyang Technological University
Does something not look right? The information on this page has been harvested from data sources that may not be up to date. We continue to work with information providers to improve coverage and quality. To report an issue, use the Feedback Form.
Publisher: AIP Publishing
Date: 13-08-2007
DOI: 10.1063/1.2772668
Abstract: Surface modification of ZnO nanocombs was performed through a Ti plasma immersion ion implantation (PIII) with low bias voltages ranging from 0to5kV to quench surface-originated exciton emission. The ion energy dependent surface modification on ZnO was investigated using transmission electron microscopy and temperature-dependent photoluminescence (PL). The surface exciton (SX) was clearly identified for the as-grown s le at 4.5K, and complete quenching was observed for s le treated with 5kV PIII due to surface state passivation. The SX related surface states were located within 5nm in depth from the surface corresponding to the implantation depth of 5kV PIII. Room-temperature PL enhancement of these surface-modified ZnO nanocombs was observed and discussed. The results show that PIII can become a viable technique for nanostructure surface passivation.
Publisher: AIP Publishing
Date: 03-2007
DOI: 10.1063/1.2709578
Abstract: Polyimide s les modified by aluminum (Al) ions produced by filtered cathodic vacuum arc (FCVA) with plasma immersion ion implantation (PIII) technique, under ambient argon and oxygen gases (flow rate Ar:O2=2:1) were investigated by x-ray photoelectron spectroscopy (XPS). The working pressure was about 8×10−4 Torr and the plasma density was estimated to be 109 ions∕cm3. The applied bias voltages were varied from 5 to 12.5 kV but with fixed frequency at 900 Hz and duty time of 15μs. For 1 min process time, C 1s and O 1s spectra for modified s les clearly indicated that the carbonyl group (C=O) was largely destroyed by incident Al ions while Al 2p spectra suggested Al atoms remain inside polyimide matrices in the form of C-O-Al complexes. For a 5 min process time, when the ion fluence became large, both C 1s and O 1s spectra suggested a structure of “aluminum oxide-mixed layer-polyimide” and Al 2p spectra confirmed that most Al atoms were bonded to oxygen atoms on the top surface. These XPS results revealed the chemical bonds between implanted and deposited Al ions and polyimide matrix by using the PIII technique. The structural information can also be suggested. Furthermore in this paper, some discussions with the theoretical [the stopping and range of ions in matter (SRIM)] simulation were also mentioned in order to explore the effectiveness of Al ions irradiation on polyimide.
Publisher: CSIRO Publishing
Date: 2012
DOI: 10.1071/CH12037
Abstract: Gold nanorods (AuNRs) possess unique optical properties which make them good contrast agents for optical microscopy. Their longitudinal plasmon resonance peak can be easily tuned from red to near infrared wavelength by increasing their aspect ratio to match the wavelengths of different imaging modalities. AuNRs are also stronger scatterers of light as compared with gold nanospheres. Nevertheless what sets them apart from other gold nanoparticles is their strong multiphoton luminescence. AuNRs are therefore being increasingly used as contrast agents for multiphoton microscopy of biological s les. In this study, control of the longitudinal resonance peak of gold nanorods is investigated with comparison of two chemical synthesis approaches. Both based on a seed-mediated method, one approach is to tune the aspect ratio through manipulation of the ratio of gold seeds to gold salt and the other is through variation of the volume of hydrochloric acid. The synthesized gold nanorods were made biocompatible by replacing the cytotoxic cetyltrimethylammonium bromide (CTAB) molecules with either silica (SiO2) or polyethylene glycol (PEG). Multiphoton imaging of gold nanorods taken up by cells was demonstrated and the effect of PEG chain length on passive uptake of gold nanorods by cells is discussed.
Publisher: American Vacuum Society
Date: 07-03-2007
DOI: 10.1116/1.2712196
Abstract: A thin passivation layer of aluminum oxide was deposited on polyimide by using the combined plasma immersion ion implantation and deposition (PIII& D) and cathodic vacuum arc technique. X-ray photoelectron spectroscopy C 1s spectra showed that the carbonyl bond (CO) and ether group (C–O–C and C–N–C) presented in pristine polyimide were damaged by implantation of aluminum ions and deposition of an aluminum oxide passivation layer. O 1s and Al 2p spectra confirmed the formation of a thin aluminum oxide passivation layer. This passivation layer can be implemented in aerospace engineering where polyimide may suffer degradation from fast atomic oxygen in the low-earth-orbit environment. To test the protection of this passivation layer to energetic oxygen ions, a plasma-enhanced chemical vapor deposition system was used to simulate the oxygen-ion irradiation, and the results showed that a higher weight occurred for passivated s les compared to pristine ones. X-ray diffraction showed that Al peaks were presented on the surface region, but no aluminum oxide peak was detected. The authors then concluded that Al clusters were formed in polyimide besides aluminum oxide, which was in an x-ray amorphous state. Furthermore, contact-angle measurements showed a reduced contact angle for passivated polyimide from a pristine value of 78° to 20° by using deionized water. Several discussions have been made on the surface chemical and structural property changes by using the combined PIII& D and cathodic vacuum arc technique.
Publisher: SPIE
Date: 23-02-2005
DOI: 10.1117/12.582855
No related grants have been discovered for Jia Yin Sze.