ORCID Profile
0000-0002-4556-3590
Current Organisation
Macquarie University
Does something not look right? The information on this page has been harvested from data sources that may not be up to date. We continue to work with information providers to improve coverage and quality. To report an issue, use the Feedback Form.
Publisher: Elsevier BV
Date: 03-2017
Publisher: Institution of Engineering and Technology (IET)
Date: 10-05-2017
Publisher: MDPI AG
Date: 08-01-2021
DOI: 10.3390/ELECTRONICS10020119
Abstract: A simple metasurface integrated with horn antenna exhibiting wide bandwidth, covering full Ku-band using 3D printing is presented. It consists of a 3D-printed horn and a 3D-printed phase transformation surface placed at the horn aperture. Considering the non-uniform wavefront of 3D printed horn, the proposed 3D-printed phase transformation surface is configured by unit cells, consisting of a cube in the centre which is supported by perpendicular cylindrical rods from its sides. Placement of proposed surface helps to improve the field over the horn aperture, resulting in lower phase variations. Both simulated and measured results show good radiation characteristics with lower side lobe levels in both E- and H-planes. Additionally, there is an overall increment in directivity with peak measured directivity up to 24.8 dBi and improvement in aperture efficiency of about 35% to 72% in the frequency range from 10–18 GHz. The total weight of the proposed antenna is about 345.37 g, which is significantly light weight. Moreover, it is a low cost and raid manufacturing solution using 3D printing technology.
Publisher: IEEE
Date: 10-2017
Publisher: IEEE
Date: 04-12-2021
Publisher: Institute of Electrical and Electronics Engineers (IEEE)
Date: 10-2021
Publisher: MDPI AG
Date: 13-06-2023
DOI: 10.3390/MI14061244
Abstract: The three-dimensional printed wideband prototype (WBP) was proposed, which is able to enhance the horn feed source by generating a more uniform phase distribution that is obtained after correcting aperture phase values. The noted phase variation obtained without the WBP was 163.65∘ for the horn source only, which was decreased to 19.68∘, obtained after the placement of the WBP at a λ/2 distance above the feed horn aperture. The corrected phase value was observed at 6.25 mm (0.25λ) above the top face of the WBP. The use of a five-layer cubic structure is able to generate the proposed WBP with dimensions of 105 mm × 105 mm × 37.5 mm (4.2λ× 4.2λ× 1.5λ), which can improve directivity and gain by 2.5 dB throughout the operating frequency range with a lower side lobe level. The overall dimension of the 3D printed horn was 98.5 mm × 75.6 mm × 192.6 mm (3.94λ× 3.02λ× 7.71λ), where the 100 % infill value was maintained. The horn was painted with a double layer of copper throughout its surface. In a design frequency of 12 GHz, the computed directivity, gain, side lobe level in H- and E- planes were 20.5 dB, 20.5 dB, −26.5 dB, and −12.4 dB with only a 3D printed horn case and, with the proposed prototype placed above this feed source, these values improved to 22.1 dB, 21.9 dB, −15.5 dB, and −17.5 dB, respectively. The realized WBP was 294 g and the overall system was 448 g in weight, which signifies a light weight condition. The measured return loss values were less than 2, which supports that the WBP has matching behavior over the operating frequency range.
Publisher: IEEE
Date: 08-2020
Publisher: MDPI AG
Date: 20-12-2021
DOI: 10.3390/ELECTRONICS10243174
Abstract: In this paper, 3D printed surfaces are presented to study this technology’s application in generating beam tilt for the electromagnetic waves in the Ku-band. Additionally, the input source is maintained by a feed horn that is additively manufactured and is coated with copper spray paint to add conductivity, which is fed by a WR-75 waveguide. The proposed beam tilt generating surface is also referred to as a Beam Deviating Surface (BDS). There is no relative gap between the BDS and the aperture of the horn, which eventually decreased the overall antenna height. The BDS layer is able to deviate the beam for a fixed elevation angle of 22.5∘ and could be consequently rotated along with the rotation of the BDS prototype. The voltage standing wave ratio value is less than two over the operating frequency range, which depicts the wideband behavior. The measured and simulated radiation patterns show that we can tilt the electromagnetic waves in ranges of up to +/−22.5∘ with a minimum side lobe level of −5 dB at frequencies from 10 to 15 GHz. This signifies the wideband characteristic of the proposed prototype, which is achieved by Vero material from Multijet Printing that is a low-cost and rapid manufacturing 3D printing technology.
Publisher: Hindawi Limited
Date: 03-03-2019
DOI: 10.1155/2019/9538061
Abstract: Rain attenuation measurement techniques are studied with appropriate prediction of rain attenuation at Ku-band for Koreasat 6. This is accomplished by the establishment of experimental setup in Mokdong at 12.25 GHz link. The databases are analyzed for three years, 2013 till 2015. During observation period, rainfall rate of 50 mm/hr is obtained which is measured by OTT Parsivel showing the signal attenuated by 10.7 dB for 0.01% of the occurrence. Comparison with the measured data demonstrates that the proposed technique provides sufficiently accurate estimation for Ku-band signal attenuation in site specifically whose effectiveness is performed through the statistical analysis against the established rain attenuation models. The proposed technique is judged through the error matrices where relative error margins of 52.82, 4.11, and 23.64% are obtained for 0.1%, 0.01%, and 0.001% of the occurrence.
Publisher: The Electromagnetics Academy
Date: 2018
Publisher: MDPI AG
Date: 19-03-2022
DOI: 10.3390/MI13030471
Abstract: A wideband antenna is proposed based on three-dimensional printing technology. The antenna was designed using the PREPERM 10 material, with permittivity ϵr = 10, where the overall height of the proposed prototype was maintained as 12.83 mm (0.51λ), having a lateral dimension of 60 mm × 60 mm, at an operating frequency of 12 GHz (λ = 25 mm). The proposed antenna achieved a wide frequency bandwidth with a voltage standing-wave ratio (VSWR) of less than two, from 10 GHz to 15 GHz in the Ku-band, where the maximum directivity was 20 dBi over a reflection coefficient bandwidth of 50%. It showed a miniaturized non-uniform metasurface of 2.4λ × 2.4λ × 0.51λ that was placed at 16.5 mm (0.66λ) above the ground plane, which was 2.4λ × 2.4λ × 0.04λ in dimension. Thus, the overall height of the proposed antenna system from the feed source was 29.33 mm (1.17λ). The total weight of the system including the designed structures made of PREPERM 10 and ABS with copper-painted prototypes was 96 g and 79 g, respectively. The measured results were consistent with the simulated results, demonstrating the feasibility and effectiveness of the proposed method.
Publisher: IEEE
Date: 09-2019
Publisher: MDPI AG
Date: 15-06-2022
DOI: 10.3390/APP12126074
Abstract: A novel flat beam steering prototype based on the specific arrangement of a cylindrical unit cell is designed, manufactured and tested. The wideband and broad scanning capability is demonstrated at the Ku-band. We have considered two configurations, first with circular rings (CR) of the defined permittivity values for respective radial distance from the center of the aperture, second with cylindrical rods that shall be placed on a respective CR, which mimics the defined permittivity. The structure is generated from Vero CMYK full color wax, which utilizes the Multijet 3D printing method. The proposed prototype is designed in the operating frequency of 12 GHz (λ = 25 mm) and separation distance between the two parallel plates are maintained at 12.5 mm (0.5λ) for the TE10 mode of operation. The diameter of the two parallel plates and the proposed structure is of 100 mm (4λ) where the radius of cylinders varies from 0.5 to 3.5 mm and corresponding relative permittivity varies from 0.6687 to 2.4395. The overall height of the structure is 12.5 mm and is placed between two parallel plates. The minimum separation distance is maintained between the proposed structure and the feed WR-75 waveguide. Irises effect is performed to obtain impedance matching in the operating frequency bands. Beam steering of the radiated waves is observed for relative rotation angles of 0∘, 30∘, 45∘, 75∘ and 90∘ of the WR-75 waveguide along the edge of parallel plates. The overall proposed system weighs 179 g, which signifies the light weight characteristics. Moreover, the proposed structure shows low return loss over 10 GHz to 15 GHz operating frequency band.
Publisher: Hindawi Limited
Date: 2017
DOI: 10.1155/2017/8694748
Abstract: The attenuation induced by rain is prominent in the satellite communication at Ku and Ka bands. The paper studied the empirical determination of the power law coefficients which support the calculation of specific attenuation from the knowledge of rain rate at Ku and Ka band for Koreasat 6 and COMS1 in South Korea that are based on the three years of measurement. Rain rate data was measured through OTT Parsivel which shows the rain rate of about 50 mm/hr and attenuation of 10.7, 11.6, and 11.3 dB for 12.25, 19.8, and 20.73 GHz, respectively, for 0.01% of the time for the combined values of rain rate and rain attenuation statistics. Comparing with the measured data illustrates the suitability for estimation of signal attenuation in Ku and Ka band whose validation is done through the comparison with prominent rain attenuation models, namely, ITU-R P.618-12 and ITU-R P. 838-3 with the use of empirically determined coefficient sets. The result indicates the significance of the ITU-R recommended regression coefficients of rain specific attenuation. Furthermore, the overview of predicted year-wise rain attenuation estimation for Ka band in the same link as well as different link is studied which is obtained from the ITU-R P. 618-12 frequency scaling method.
Publisher: IEEE
Date: 05-07-2020
Publisher: IEEE
Date: 02-2020
Publisher: Elsevier BV
Date: 2017
Publisher: Springer Science and Business Media LLC
Date: 12-04-2016
Publisher: MDPI AG
Date: 02-2021
DOI: 10.3390/ELECTRONICS10030333
Abstract: A simple, nearfield transformation meta-structure is proposed to increase the directivity of resonant cavity antennas (RCA). The meta-structure is comprised of 14 × 14 meta-atoms or so called “unit-cells”, adding localized phase delays in the aperture of the RCA and thus increasing its broadside directivity. A prototype of the meta-structure is additively manufactured using the stereolithograpy process and has a profile of 0.56λ. With the meta-structure integrated with the RCA, it demonstrates a measured broadside directivity of 20.15 dBi without affecting its half-power directivity bandwidth. Benefiting from additive manufacturing, the proposed approach is a simple, light-weight, low-cost, and planar approach that can be tailored to achieve medium-to-high gains with RCAs.
Publisher: Hindawi Limited
Date: 31-03-2019
DOI: 10.1155/2019/1712791
Abstract: Absorption of microwave radio frequency signal by atmospheric rain and losses is prevalent at frequencies above 5 GHz. The functioning frequencies of 18 GHz are taken for the point-to-point microwave link system. This paper presents studies on rain attenuation at 18 GHz, which specifies minimum performance parameters for terrestrial fixed service digital radio communication equipment. It presents a 3.2 km experimental link at 18 GHz between Khumdang (Korea Telecom, KT station) and Icheon (National Radio Research Agency, RRA station). The received signal data for rain attenuation and the rain rate were collected at 10-second intervals over three year’s periods from 2013 to 2015. During the observation period, rain rates of about 50 mm/hr and attenuation values of 33.38 dB and 21.88 dB occurred for 0.01% of the time for horizontal and vertical polarization. This paper highlights the discussion and comparison of ITU-R P.530-16, Moupfouma, Silva Mello, and Abdulrahman models and proposed an attenuation prediction approach where it presents the relationship between theoretical specific rain attenuation as specified by ITU-R P.838-3, γ % p , and effective specific rain attenuation, γ eff . Additionally, it studies 1-minute rain rates derived from higher time integration of 5-minute, 10-minute, 20-minute, 30-minute, and 60-minute instances which are obtained from experimental 1-minute rainfall amounts that are maintained by the Korea Meteorological Administration (KMA). The effectiveness of the proposed approach is further analyzed for 38 and 75 GHz links which shows better prediction capability. Particularly, in an 18 GHz link under horizontal polarization, ITU-R P. 530-16 shows the relative error margin of 71%, 60%, and 38% where as 64%, 49%, and 42% were obtained under vertical polarization for 0.1%, 0.01%, and 0.001% of the time, respectively. The limitation of research lies on the experimental system that is set up in only one location however, the preliminary results indicate the application of a suitable 1-minute rain attenuation model for a specific site. The method provides useful information for microwave engineers and researchers in making decisions over the choice of the most suitable rain attenuation prediction for terrestrial links operating in the South Korea region, particularly for lower frequency ranges.
Publisher: Elsevier BV
Date: 10-2016
Publisher: IEEE
Date: 09-2019
Publisher: Institute of Electrical and Electronics Engineers (IEEE)
Date: 2022
No related grants have been discovered for Sujan Shrestha.