ORCID Profile
0000-0003-4756-595X
Current Organisation
Gwangju Institute of Science and Technology
Does something not look right? The information on this page has been harvested from data sources that may not be up to date. We continue to work with information providers to improve coverage and quality. To report an issue, use the Feedback Form.
In Research Link Australia (RLA), "Research Topics" refer to ANZSRC FOR and SEO codes. These topics are either sourced from ANZSRC FOR and SEO codes listed in researchers' related grants or generated by a large language model (LLM) based on their publications.
Engineering | Environmental sciences | Mechanical engineering | Earth sciences | Soil sciences | Geophysics
There are no SEO codes available for Dr Mohammad Boshir Ahmed
Publisher: Elsevier BV
Date: 07-2018
Publisher: Elsevier BV
Date: 12-2022
Publisher: Elsevier BV
Date: 03-2017
Publisher: Bangladesh Journals Online (JOL)
Date: 28-03-2016
DOI: 10.3329/BJSIR.V51I1.27031
Abstract: Objective of this work was to pyrolysis woody biomass. Experiments were carried out at 300 to 500oC. Relatively bigger particles were used. Special emphasis was given to investigate the effects of heating rate and heating up time of the central mass of the particles on the product distribution. Surface temperature reached to the reactor set temperature immediately while the temperature at the central part was as low as 50oC. The center temperature gradually increased to the final temperature within 3 to 8 minutes, depending on the wood types and the reactor set temperature. For ipil-ipil wood the heating rate of the central mass was much faster than krishnachura and koroi woods, and thus the heating up time was lower. Ipil-ipil wood was experienced higher yield (65%) even at lower reactor temperature 300oC with particle temperature 450oC. In the case of krishnachura and koroi woods, the bio-oil yields were lower under the same condition due to the heating rates of the central parts were much slower. Further researchon different biomasses may be necessary to demonstrate overall process.Bangladesh J. Sci. Ind. Res. 51(1), 13-22, 2016
Publisher: MDPI AG
Date: 06-02-2020
DOI: 10.3390/PR8020203
Abstract: Activated carbon (AC) has been extensively utilized as an adsorbent over the past few decades. AC has widespread applications, including the removal of different contaminants from water and wastewater, and it is also being used in capacitors, battery electrodes, catalytic supports, and gas storage materials because of its specific characteristics e.g., high surface area with electrical properties. The production of AC from naturally occurring precursors (e.g., coal, biomass, coconut shell, sugarcane bagasse, and so on) is highly interesting in terms of the material applications in chemistry however, recently much focus has been placed on the use of agricultural wastes (e.g., rice husk) to produce AC. Rice husk (RH) is an abundant as well as cheap material which can be converted into AC for various applications. Various pollutants such as textile dyes, organic contaminants, inorganic anions, pesticides, and heavy metals can be effectively removed by RH-derived AC. In addition, RH-derived AC has been applied in supercapacitors, electrodes for Li-ion batteries, catalytic support, and energy storage, among other uses. Cost-effective synthesis of AC can be an alternative for AC production. Therefore, this review mainly covers different synthetic routes and applications of AC produced from RH precursors. Different environmental, catalytic, and energy applications have been pinpointed. Furthermore, AC regeneration, desorption, and relevant environmental concerns have also been covered. Future scopes for further research and development activities are also discussed. Overall, it was found that RH-derived AC has great potential for different applications which can be further explored at real scales, i.e., for industrial applications in the future.
Publisher: Elsevier
Date: 2020
Publisher: Elsevier BV
Date: 2018
DOI: 10.1016/J.SCITOTENV.2017.08.097
Abstract: Gold-modified TiO
Publisher: Elsevier BV
Date: 02-2017
DOI: 10.1016/J.JHAZMAT.2016.04.045
Abstract: This review focuses on the removal of emerging contaminants (ECs) by biological, chemical and hybrid technologies in effluents from wastewater treatment plants (WWTPs). Results showed that endocrine disruption chemicals (EDCs) were better removed by membrane bioreactor (MBR), activated sludge and aeration processes among different biological processes. Surfactants, EDCs and personal care products (PCPs) can be well removed by activated sludge process. Pesticides and pharmaceuticals showed good removal efficiencies by biological activated carbon. Microalgae treatment processes can remove almost all types of ECs to some extent. Other biological processes were found less effective in ECs removal from wastewater. Chemical oxidation processes such as ozonation/H
Publisher: Elsevier BV
Date: 09-2021
Publisher: Elsevier BV
Date: 03-2020
DOI: 10.1016/J.CHEMOSPHERE.2019.125366
Abstract: The global occurrence and adverse environmental impacts of perfluorooctanoic acid (PFOA) have attracted wide attention. This study focused on the PFOA photodegradation by using photocatalyst TiO
Publisher: Springer Science and Business Media LLC
Date: 21-11-2013
Publisher: Wiley
Date: 28-11-2022
Abstract: Carbon has an extraordinary ability to bind with itself and other elements, resulting in unique structures for a wide range of applications. Recently, intensive research has been focused on the properties of carbon‐based materials (CBMs) and on increasing their performance by doping them with metals and non‐metallic elements. While materials with excellent performance have been experimentally achieved, a fundamental knowledge of the relationship between the electronic, physical, and electrochemical properties and their structural features, particularly the chemistry of carbon‐based materials remains a top challenge. This review begins with the doping chemistries of CBMs, covering the role of electron affinity, orbital chemistry, the chemistry of band gap, conductivity, bonding type, spin redistribution, and conducting relevant comparisons. These will lead to providing an in‐depth understanding of the overall picture in the CBMs doping chemistry particularly as catalysts. The future research prospects and challenges for doped CBMs are highlighted.
Publisher: Elsevier BV
Date: 08-2022
Publisher: Elsevier BV
Date: 10-2018
Publisher: Elsevier BV
Date: 03-2019
DOI: 10.1016/J.NEURO.2018.12.002
Abstract: Welding involves exposure to fumes, gases and radiant energy that can be hazardous to human health. Welding fumes (WFs) comprise a complex mixture of metallic oxides, silicates and fluorides that may result in different health effects. Inhalation of WFs in large quantities over a long periods may pose a risk of developing neurodegenerative diseases (NDGDs), but the nature of this risk is poorly understood. To address this we performed transcriptomic analysis to identify links between WF exposure and NDGDs. We developed quantitative frameworks to identify the gene expression relationships of WF exposure and NDGDs. We analyzed gene expression microarray data from fume-exposed tissues and NDGDs including Parkinson's disease (PD), Alzheimer's disease (AD), Lou Gehrig's disease (LGD), Epilepsy disease (ED) and multiple sclerosis disease (MSD) datasets. We constructed disease-gene relationship networks and identified dysregulated pathways, ontological pathways and protein-protein interaction sub-network using multilayer network topology and neighborhood-based benchmarking. We observed that WF associated genes share 18, 16, 13, 19 and 19 differentially expressed genes with PD, AD, LGD, ED and MSD respectively. Gene expression dysregulation along with relationship networks, pathways and ontologic analysis indicate that WFs may be linked to the progression of these NDGDs. Our developed network-based approach to analysis and investigate the genetic effects of welding fumes on PD, AD, LGD, ED and MSD neurodegenerative diseases could be helpful to understand the causal influences of WF exposure for the progression of the NDGDs.
Publisher: MDPI AG
Date: 19-07-2022
DOI: 10.3390/PR10071408
Abstract: Perovskite solar cells (PSCs) have captured the attention of the global energy research community in recent years by showing an exponential augmentation in their performance and stability. The supremacy of the light-harvesting efficiency and wider band gap of perovskite sensitizers have led to these devices being compared with the most outstanding rival silicon-based solar cells. Nevertheless, there are some issues such as their poor lifetime stability, considerable J–V hysteresis, and the toxicity of the conventional constituent materials which restrict their prevalence in the marketplace. The poor stability of PSCs with regard to humidity, UV radiation, oxygen and heat especially limits their industrial application. This review focuses on the in-depth studies of different direct and indirect parameters of PSC device instability. The mechanism for device degradation for several parameters and the complementary materials showing promising results are systematically analyzed. The main objective of this work is to review the effectual strategies of enhancing the stability of PSCs. Several important factors such as material engineering, novel device structure design, hole-transporting materials (HTMs), electron-transporting materials (ETMs), electrode materials preparation, and encapsulation methods that need to be taken care of in order to improve the stability of PSCs are discussed extensively. Conclusively, this review discusses some opportunities for the commercialization of PSCs with high efficiency and stability.
Publisher: Bangladesh Journals Online (JOL)
Date: 2011
Abstract: The objective of the present work is to install a modified suitable and compatible reactor system for the efficient production of renewable liquid fuel (bio-oil) from agro-based bio-mass. This new type of reactor system contains a combustor connected with the upper end of the reactor chamber. The bottom end of the reactor is connected with the bottom part of the combustor by a stainless steel pipe through which hot sand is circulated by the force of air pump. Thus, effective heat transfer from the continuously circulated heated sand as well as efficient biomass conversion into the reactor can be obtained. In this work, jute stick and bagasse abundantly available in Bangladesh were pyrolyzed separately in a continuous feeding circulating fluidized bed reactor at around 500°C for bio-oil production. The total bio-oil yields from bagasse and jute stick were about 69.5 wt% and 68.2 wt% respectively, which are higher than the yields obtained from fixed bed pyrolysis reactor. The total yields of char contents were 19.4 wt% and 21.7wt% after complete pyrolysis of bagasse and jute stick respectively, which are less than that of char yields obtained from fixed bed pyrolysis reactor. Physical and chemical analyses of bio-oils were carried out by conventional methods. The density, viscosity, pH, acid value, water, lignin, solid and ash contents of bio-oils obtained from both jute stick and bagasse were found to be 1.1 g/cc, 3.1 cp, 4.1, 126.3 mgKOH/g, 14.0 wt%, 2.5wt%, 0.05wt%, 0.03wt%, and 1.12 g/cc, 3.2cp, 4.0, 127.1 mgKOH/g, 13.0 wt%, 2.5wt%, 0.015wt%, 0.025wt%, respectively. Key words: Renewable energy Bio-mass Bio-oil Pyrolysis Fluid bed circulating reactor DOI: 0.3329/bjsir.v46i3.9036 BJSIR 2011 46(3): 313-322
Publisher: MDPI AG
Date: 14-03-2022
DOI: 10.3390/GELS8030177
Abstract: There is a great demand for biodegradable hydrogel, and cellulose enriched wastes materials are widely used to serve this purpose for various advance applications (e.g., biomedical and environmental). Sugarcane bagasse is cellulose-enriched agro-waste, abundantly grown in Bangladesh. This study aimed to treat sugarcane bagasse-based agro-waste using a sustainable and ecofriendly approach to produce hydrogel with super-swelling capacity for adsorption of copper, chromium, iron ions, methylene blue and drimaren red dyes. To increase the swelling property of hydrogels, copolymerization of hydrophilic monomers is an effective technique. Therefore, this study aimed to prepare hydrogel via free radical graft-copolymerization reaction among acrylamide, methyl methacrylate and treated bagasse in the presence of N,N-methylene-bis-acrylamide as a crosslinker and potassium persulphate as an initiator. To obtain maximum yield, reaction conditions were optimized. It was found that hydrogel obtained from chemically treated sugarcane bagasse showed maximum water absorption capacity of 228.0 g/g, whereas untreated bagassebased hydrogel could absorb ~50 g/g of water. Maximum adsorption capacity of 247.0 mg/g was found for copper ion. In addition, organic pollutant removal from industrial effluent also showed good performance, removing % of methylene blue and 62% of drimaren red dye, with shorter kinetics. The biodegradability study showed that after 90 days of exposure, the hydrogels degraded to about 43% of their own mass. Therefore, the produced hydrogel could be an alternative adsorbent to remove pollutants and also for other potential applications.
Publisher: Elsevier BV
Date: 05-2019
DOI: 10.1016/J.COMPBIOMED.2019.04.004
Abstract: The welding process releases potentially hazardous gases and fumes, mainly composed of metallic oxides, fluorides and silicates. Long term welding fume (WF) inhalation is a recognized health issue that carries a risk of developing chronic health problems, particularly respiratory system diseases (RSDs). Aside from general airway irritation, WF exposure may drive direct cellular responses in the respiratory system which increase risk of RSD, but these are not well understood. We developed a quantitative framework to identify gene expression effects of WF exposure that may affect RSD development. We analyzed gene expression microarray data from WF-exposed tissues and RSD-affected tissues, including chronic bronchitis (CB), asthma (AS), pulmonary edema (PE), lung cancer (LC) datasets. We built disease-gene (diseasome) association networks and identified dysregulated signaling and ontological pathways, and protein-protein interaction sub-network using neighborhood-based benchmarking and multilayer network topology. We observed many genes with altered expression in WF-exposed tissues were also among differentially expressed genes (DEGs) in RSD tissues for CB, AS, PE and LC there were 34, 27, 50 and 26 genes respectively. DEG analysis, using disease association networks, pathways, ontological analysis and protein-protein interaction sub-network suggest significant links between WF exposure and the development of CB, AS, PE and LC. Our network-based analysis and investigation of the genetic links of WFs and RSDs confirm a number of genes and gene products are plausible participants in RSD development. Our results are a significant resource to identify causal influences on the development of RSDs, particularly in the context of WF exposure.
Publisher: Elsevier BV
Date: 08-2017
Publisher: MDPI AG
Date: 20-04-2021
Abstract: Carboxymethyl cellulose (CMC) is one of the most promising cellulose derivatives. Due to its characteristic surface properties, mechanical strength, tunable hydrophilicity, viscous properties, availability and abundance of raw materials, low-cost synthesis process, and likewise many contrasting aspects, it is now widely used in various advanced application fields, for ex le, food, paper, textile, and pharmaceutical industries, biomedical engineering, wastewater treatment, energy production, and storage energy production, and storage and so on. Many research articles have been reported on CMC, depending on their sources and application fields. Thus, a comprehensive and well-organized review is in great demand that can provide an up-to-date and in-depth review on CMC. Herein, this review aims to provide compact information of the synthesis to the advanced applications of this material in various fields. Finally, this article covers the insights of future CMC research that could guide researchers working in this prominent field.
Publisher: Elsevier BV
Date: 08-2017
Publisher: Elsevier BV
Date: 12-2020
Publisher: Elsevier BV
Date: 08-2016
DOI: 10.1016/J.BIORTECH.2016.05.057
Abstract: Modified biochar (BC) is reviewed in its preparation, functionality, applications and regeneration. The nature of precursor materials, preparatory conditions and modification methods are key factors influencing BC properties. Steam activation is unsuitable for improving BC surface functionality compared with chemical modifications. Alkali-treated BC possesses the highest surface functionality. Both alkali modified BC and nanomaterial impregnated BC composites are highly favorable for enhancing the adsorption of different contaminants from wastewater. Acidic treatment provides more oxygenated functional groups on BC surfaces. The Langmuir isotherm model provides the best fit for sorption equilibria of heavy metals and anionic contaminants, while the Freundlich isotherm model is the best fit for emerging contaminants. The pseudo 2(nd) order is the most appropriate model of sorption kinetics for all contaminants. Future research should focus on industry-scale applications and hybrid systems for contaminant removal due to scarcity of data.
Publisher: MDPI AG
Date: 29-04-2023
Abstract: Developing cost-effective, eco-friendly, efficient, stable, and unique catalytic systems remains a crucial issue in catalysis. Due to their superior physicochemical and electrochemical properties, exceptional structural characteristics, environmental friendliness, economic productivity, minimal energy demand, and abundant supply, a significant amount of research has been devoted to the development of various doped carbon materials as efficient catalysts. In addition, carbon-based materials (CBMs) with specified doping have lately become significant members of the carbon group, showing promise for a broad range of uses (e.g., catalysis, environmental remediation, critical chemical production, and energy conversion and storage). This study will, therefore, pay attention to the function of heteroatom-based doped and undoped CBMs for catalytical applications and discuss the underlying chemistries of catalysis. According to the findings, doping CBMs may greatly improve their catalytic activity, and heteroatom-doped CBMs may be a promising option for further metal doping to attach them to an appropriate place. This paper also covers the potential applications of both doped and undoped CBMs in the future.
Publisher: MDPI AG
Date: 19-06-2020
DOI: 10.3390/PR8060711
Abstract: Lignocellulosic biomass is widely grown in many agricultural-based countries. These are typically incinerated or discarded in open spaces, which further may cause severe health and environmental problems. Hence, the proper utilization and conversion of different parts of lignocellulosic biomasses (e.g., corn wastes derived leave, cob, stalk, and husk) into value-added materials could be a promising way of protecting both health and environments. In addition, they have high-potential for myriads applications (e.g., pharmaceuticals, cosmetics, textiles, and so on). In this context, herein, we isolated holocellulose (a mixture of alpha α, beta β, and gamma γ cellulose) from corn waste, and then it was converted into carboxymethyl cellulose (CMC). Subsequently, the prepared CMC was evaluated successfully to be used as a pharmaceutical excipient. Different characterization tools were employed for structural, morphological, and thermal properties of the extracted holocellulose and synthesized CMC. Results showed that the highest yield of CMC was obtained 187.5% along with the highest degree of substitution (DS i.e., 1.83) in a single stage (i.e., size reduction technique) with the lowest particle size of holocellulose (100 µm). This happened due to the use of a single stage instead of multiple stages. Finally, extracted CMC was successfully used as a pharmaceutical excipient with promising results compared to commercially available pharmaceutical-grade CMC.
Publisher: Elsevier BV
Date: 09-2022
DOI: 10.1016/J.JENVMAN.2022.115497
Abstract: The adsorption of inorganic arsenic (As) plays an important role in the mobility and transport of As in the river environment. In this work, the adsorption and desorption of arsenite [As(III)] and arsenate [As(V)] on river sediment were conducted under different pH, initial As concentrations, river water and sediment composition to assess As adsorption behavior and mechanism. Both adsorption kinetics and equilibrium results showed higher adsorption capacity of sediment for As(V) than As(III). Adsorption of As(III) and As(V) on river sediment was favored in acidic to neutral conditions and on finer sediment particles, while sediment organic matter marginally reduced adsorption capacity. In addition, higher adsorption affinity of As(III) and As(V) in river sediment was observed in deionised water than in river water. For the release process, the desorption of both As(III) and As(V) followed nonlinear kinetic models well, showing higher amount of As(III) release from sediment than As(V). Adsorption isotherm was well described by both Langmuir and Freundlich models, demonstrating higher maximum adsorption capacity of As(V) at 298.7 mg/kg than As(III) at 263.3 mg/kg in deionised water, and higher maximum adsorption capacity of As(III) of 234.3 mg/kg than As(V) of 206.2 mg/kg in river water. The XRD showed the changes in the peaks of mineral groups of sediment whilst FTIR results revealed the changes related to surface functional groups before and after adsorption, indicating that Fe-O/Fe-OH, Si(Al)-O, hydroxyl and carboxyl functional groups were predominantly involved in As(III) and As(V) adsorption on sediment surface. XPS analysis evidenced the transformation between these As species in river sediment after adsorption, whilst SEM-EDS revealed higher amount of As(V) in river sediment than As(III) due to the lower signal of Al.
Publisher: MDPI AG
Date: 03-2023
Abstract: Over the last decade, researchers have investigated the potential of nano and microfiber scaffolds to promote wound healing, tissue regeneration, and skin protection. The centrifugal spinning technique is favored over others due to its relatively straightforward mechanism for producing large quantities of fiber. Many polymeric materials have yet to be investigated in search of those with multifunctional properties that would make them attractive in tissue applications. This literature presents the fundamental process of fiber generation, and the effects of fabrication parameters (machine, solution) on the morphologies such as fiber diameter, distribution, alignment, porous features, and mechanical properties. Additionally, a brief discussion is presented on the underlying physics of beaded morphology and continuous fiber formation. Consequently, the study provides an overview of the current advancements in centrifugally spun polymeric fiber-based materials and their morphological features, performance, and characteristics for tissue engineering applications.
Publisher: Elsevier BV
Date: 02-2020
Publisher: Elsevier BV
Date: 2020
DOI: 10.1016/J.CHEMOSPHERE.2019.124722
Abstract: Perfluorooctanoic acid (PFOA) has attracted considerable attention worldwide due to its widespread occurrence and environmental impacts. This research focused on the photocatalytic process for the treatment of PFOA in water and wastewater. Gallium oxide (Ga
Publisher: Elsevier
Date: 2021
Publisher: Springer Science and Business Media LLC
Date: 07-05-2019
DOI: 10.1007/S10653-019-00302-W
Abstract: The contamination and risk by nutrients (NH
Publisher: Elsevier BV
Date: 12-2018
DOI: 10.1016/J.BIORTECH.2018.08.046
Abstract: The sorptive removal of dissolved organic matter (DOM) in biologically-treated effluent was studied by using multi-walled carbon nanotube (MWCNT), carboxylic functionalised MWCNT (MWCNT-COOH), hydroxyl functionalized MWCNT (MWCNT-OH) and functionalized biochar (fBC). DOM was dominated by hydrophilic fraction (79.6%) with a significantly lower hydrophobic fraction (20.4%). The sorption of hydrophobic DOM was not significantly affected by the sorbent functionality (∼10.4% variation) and sorption capacity followed the order of MWCNT > MWCNT-COOH > MWCNT-OH > fBC. In comparison, the sorption of hydrophilic fraction of DOM changed significantly (∼37.35% variation) with the change of sorbent functionality with adsorption capacity decreasing as MWCNT-OH > MWCNT-COOH > MWCNT > fBC. Furthermore, the affinity of adsorbents toward a hydrophilic compound (dinitrobenzene), a hydrophobic compound (pyrene) and humic acid was also evaluated to validate the proposed mechanisms. The results provided important insights on the type of sorbents which are most effective to remove different DOM fractions.
Publisher: Elsevier BV
Date: 08-2017
DOI: 10.1016/J.BIORTECH.2017.04.042
Abstract: Competitive sorption of sulfamethazine (SMT), sulfamethoxazole (SMX), sulfathiazole (STZ) and chlor henicol (CP) toward functionalized biochar (fBC) was highly pH dependent with maximum sorption at pH ∼4.0-4.25. Equilibrium data were well represented by the Langmuir and Freundlich models in the order STZ>SMX>CP>SMT. Kinetics data were slightly better fitted by the pseudo second-order model than pseudo first-order and intra-particle-diffusion models. Maximum sorptive interactions occurred at pH 4.0-4.25 through H-bonds formations for neutral sulfonamides species and through negative charge assisted H-bond (CAHB) formation for CP, in addition to π-π electron-donor-acceptor (EDA) interactions. EDA was the main mechanism for the sorption of positive sulfonamides species and CP at pH 7.0 was regulated by H-bond formation and proton exchange with water by forming CAHB, respectively. The results suggested fBC to be highly efficient in removing antibiotics mixture.
Publisher: Elsevier BV
Date: 10-2018
DOI: 10.1016/J.JHAZMAT.2018.08.005
Abstract: The sorption of five potent endocrine disruptors as representative hydrophobic organic contaminants (HOCs) namely estrone (E1), 17β-estradiol (E2), estriol (E3), 17α-ethynylestradiol (EE2) and bisphenol A (BPA) on functionalized biochar (fBC) was systematically examined, with a particular focus on the importance of π-electron-donor (phenanthrene: PHEN) and π-electron-acceptors (1,3-dinitrobenzene: DNB, p-amino benzoic acid: PABA) on sorption. Experimental results suggested that hydrogen-bond formation and π-π-electron-donor-acceptor (EDA) interactions were the dominant sorption mechanisms. The sorption of HOCs decreased as E1 > E2 > EE2 > E3 > BPA based on the Freundlich and Polanyi-Mane-models. The comparison of adsorption coefficient (K
Publisher: Elsevier BV
Date: 11-2015
DOI: 10.1016/J.SCITOTENV.2015.05.130
Abstract: Antibiotics as emerging contaminants are of global concern due to the development of antibiotic resistant genes potentially causing superbugs. Current wastewater treatment technology cannot sufficiently remove antibiotics from sewage, hence new and low-cost technology is needed. Adsorptive materials have been extensively used for the conditioning, remediation and removal of inorganic and organic hazardous materials, although their application for removing antibiotics has been reported for ~30 out of 250 antibiotics so far. The literature on the adsorptive removal of antibiotics using different adsorptive materials is summarized and critically reviewed, by comparing different adsorbents with varying physicochemical characteristics. The efficiency for removing antibiotics from water and wastewater by different adsorbents has been evaluated by examining their adsorption coefficient (Kd) values. For sulfamethoxazole the different adsorbents followed the trend: biochar (BC)> multi-walled carbon nanotubes (MWCNTs)>graphite = clay minerals, and for tetracycline the adsorptive materials followed the trend: SWCNT > graphite > MWCNT = activated carbon (AC) > bentonite = humic substance = clay minerals. The underlying controlling parameters for the adsorption technology have been examined. In addition, the cost of preparing adsorbents has been estimated, which followed the order of BCs < ACs < ion exchange resins < MWCNTs < SWCNTs. The future research challenges on process integration, production and modification of low-cost adsorbents are elaborated.
Publisher: Elsevier BV
Date: 03-2018
Publisher: Elsevier BV
Date: 08-2018
DOI: 10.1016/J.SCITOTENV.2018.03.206
Abstract: Graphitic carbon nitride (g-C
Publisher: Wiley
Date: 29-05-2019
DOI: 10.1111/AJO.12989
Abstract: Increasingly, couples are seeking assistance to conceive. It is not clear whether obstetric and gynaecological trainees in Australia and New Zealand receive adequate training and exposure to infertility training. To determine the perspectives of Royal Australian and New Zealand College of Obstetrics and Gynaecology (RANZCOG) trainees regarding their experience of infertility management during training, in order to better inform discussions of training in this area. RANZCOG trainees were invited to participate in an anonymous online survey containing 17 questions. Data collected included demographic details, training year, cumulative infertility experience as a trainee, and perspectives regarding infertility experience during training. Of the 191 RANZCOG trainees who participated in the study (25.7% response rate), the majority reported they had never had the opportunity to attend an infertility clinic as part of their training (53.2%). Lack of experience in infertility medicine was associated with a high dissatisfaction rate (89.8%). Trainees in Australia and New Zealand have limited access to infertility medicine during training with associated high dissatisfaction rates. Access to training in a private healthcare setting or the expansion of public in vitro fertilisation may improve trainees' experiences.
Publisher: Elsevier BV
Date: 07-2018
DOI: 10.1016/J.IJBIOMAC.2018.02.152
Abstract: The in vitro antioxidant, cytotoxic and cytoprotective properties and in vivo hepatoprotective activities of crude polysaccharides extracted from cyanobacteria Phormidim versicolor NCC466 (CFv-PS) were investigated. The CFv-PS, identified as heteropolysaccharides with molecular weight of 63.79kDa, exhibited relatively strong antioxidant activity, in a concentration-depended manner, in vitro assays. Additionally, CFv-PS did not induce cytotoxic effect on HepG2 human hepatocellular carcinoma cells within the range of tested concentrations (25-150μg·mL
Publisher: Elsevier BV
Date: 2016
Publisher: Wiley
Date: 23-03-2023
Publisher: Bangladesh Journals Online (JOL)
Date: 28-03-2016
DOI: 10.3329/BJSIR.V51I1.27031
Abstract: Objective of this work was to pyrolysis woody biomass. Experiments were carried out at 300 to 500oC. Relatively bigger particles were used. Special emphasis was given to investigate the effects of heating rate and heating up time of the central mass of the particles on the product distribution. Surface temperature reached to the reactor set temperature immediately while the temperature at the central part was as low as 50oC. The center temperature gradually increased to the final temperature within 3 to 8 minutes, depending on the wood types and the reactor set temperature. For ipil-ipil wood the heating rate of the central mass was much faster than krishnachura and koroi woods, and thus the heating up time was lower. Ipil-ipil wood was experienced higher yield (65%) even at lower reactor temperature 300oC with particle temperature 450oC. In the case of krishnachura and koroi woods, the bio-oil yields were lower under the same condition due to the heating rates of the central parts were much slower. Further researchon different biomasses may be necessary to demonstrate overall process.Bangladesh J. Sci. Ind. Res. 51(1), 13-22, 2016
Publisher: Elsevier BV
Date: 10-2019
DOI: 10.1016/J.COMPBIOMED.2019.103385
Abstract: Identification of genes whose regulation of expression is functionally similar in both brain tissue and blood cells could in principle enable monitoring of significant neurological traits and disorders by analysis of blood s les. We thus employed transcriptional analysis of pathologically affected tissues, using agnostic approaches to identify overlapping gene functions and integrating this transcriptomic information with expression quantitative trait loci (eQTL) data. Here, we estimate the correlation of gene expression in the top-associated cis-eQTLs of brain tissue and blood cells in Parkinson's Disease (PD). We introduced quantitative frameworks to reveal the complex relationship of various biasing genetic factors in PD, a neurodegenerative disease. We examined gene expression microarray and RNA-Seq datasets from human brain and blood tissues from PD-affected and control in iduals. Differentially expressed genes (DEG) were identified for both brain and blood cells to determine common DEG overlaps. Based on neighborhood-based benchmarking and multilayer network topology approaches we then developed genetic associations of factors with PD. Overlapping DEG sets underwent gene enrichment using pathway analysis and gene ontology methods, which identified candidate common genes and pathways. We identified 12 significantly dysregulated genes shared by brain and blood cells, which were validated using dbGaP (gene SNP-disease linkage) database for gold-standard benchmarking of their significance in disease processes. Ontological and pathway analyses identified significant gene ontology and molecular pathways that indicate PD progression. In sum, we found possible novel links between pathological processes in brain tissue and blood cells by examining cell pathway commonalities, corroborating these associations using well validated datasets. This demonstrates that for brain-related pathologies combining gene expression analysis and blood cell cis-eQTL is a potentially powerful analytical approach. Thus, our methodologies facilitate data-driven approaches that can advance knowledge of disease mechanisms and may, with clinical validation, enable prediction of neurological dysfunction using blood cell transcript profiling.
Publisher: Elsevier BV
Date: 12-2017
DOI: 10.1016/J.IJBIOMAC.2017.06.046
Abstract: In this study, response surface methodology (RSM) based on Box-Behnken design (BBD) was employed to optimize the aqueous extraction of crude polysaccharides from Tunisian cyanobacteria Phormidium versicolor (NCC 466). The optimal extraction conditions with an extraction yield of 21.56±0.92% were as follows: extraction temperature at 81.05°C, extraction time of 3.99h, and water to raw material ratio of 21.52mLg
Publisher: Springer Science and Business Media LLC
Date: 17-02-2020
DOI: 10.1038/S41598-020-57916-9
Abstract: Welding generates and releases fumes that are hazardous to human health. Welding fumes (WFs) are a complex mix of metallic oxides, fluorides and silicates that can cause or exacerbate health problems in exposed in iduals. In particular, WF inhalation over an extended period carries an increased risk of cancer, but how WFs may influence cancer behaviour or growth is unclear. To address this issue we employed a quantitative analytical framework to identify the gene expression effects of WFs that may affect the subsequent behaviour of the cancers. We examined datasets of transcript analyses made using microarray studies of WF-exposed tissues and of cancers, including datasets from colorectal cancer (CC), prostate cancer (PC), lung cancer (LC) and gastric cancer (GC). We constructed gene-disease association networks, identified signaling and ontological pathways, clustered protein-protein interaction network using multilayer network topology, and analyzed survival function of the significant genes using Cox proportional hazards (Cox PH) model and product-limit (PL) estimator. We observed that WF exposure causes altered expression of many genes (36, 13, 25 and 17 respectively) whose expression are also altered in CC, PC, LC and GC. Gene-disease association networks, signaling and ontological pathways, protein-protein interaction network, and survival functions of the significant genes suggest ways that WFs may influence the progression of CC, PC, LC and GC. This quantitative analytical framework has identified potentially novel mechanisms by which tissue WF exposure may lead to gene expression changes in tissue gene expression that affect cancer behaviour and, thus, cancer progression, growth or establishment.
Publisher: Elsevier BV
Date: 12-2017
DOI: 10.1016/J.SCITOTENV.2017.07.239
Abstract: Biochar and functionalized biochar (fBC-1 and fBC-2) were prepared and applied to remove antibiotic chlor henicol from deionized water, lake water and synthetic wastewater. Results showed that chlor henicol removal on biochar was pH dependent and maximum sorption occurred at pH4.0-4.5. The sorption data of chlor henicol fitted better with the Langmuir isotherm model than the Freundlich isotherm model with the maximum Langmuir sorption capacity of 233μMg
Publisher: Elsevier BV
Date: 12-2020
Publisher: Elsevier BV
Date: 04-2020
Publisher: MDPI AG
Date: 30-05-2020
DOI: 10.3390/PR8060654
Abstract: Carbon dioxide (CO2), a major greenhouse gas, capture has recently become a crucial technological solution to reduce atmospheric emissions from fossil fuel burning. Thereafter, many efforts have been put forwarded to reduce the burden on climate change by capturing and separating CO2, especially from larger power plants and from the air through the utilization of different technologies (e.g., membrane, absorption, microbial, cryogenic, chemical looping, and so on). Those technologies have often suffered from high operating costs and huge energy consumption. On the right side, physical process, such as adsorption, is a cost-effective process, which has been widely used to adsorb different contaminants, including CO2. Henceforth, this review covered the overall efficacies of CO2 adsorption from air at 196 K to 343 K and different pressures by the carbon-based materials (CBMs). Subsequently, we also addressed the associated challenges and future opportunities for CBMs. According to this review, the efficacies of various CBMs for CO2 adsorption have followed the order of carbon nanomaterials (i.e., graphene, graphene oxides, carbon nanotubes, and their composites) mesoporous -microporous or hierarchical porous carbons biochar and activated biochar activated carbons.
Publisher: Elsevier BV
Date: 10-2021
Publisher: Elsevier BV
Date: 07-2019
Publisher: Elsevier BV
Date: 06-2021
Publisher: Elsevier BV
Date: 03-2019
Publisher: Elsevier BV
Date: 12-2017
DOI: 10.1016/J.CHEMOSPHERE.2017.09.110
Abstract: This review focuses on heterogeneous photocatalysis of perfluoroalkyl substances (PFAS) which are of worldwide concern as emerging persistent organic contaminants. Heterogeneous photocatalysis is an effective and advanced technology for PFAS removal from water with relatively high efficacy. During photocatalysis, various short chain perfluorocarboxylic acids (PFCA) are produced as intermediates and the efficacy is related to the photo-generated hole (h
Publisher: Elsevier BV
Date: 05-2014
Publisher: Elsevier BV
Date: 08-2021
Publisher: Elsevier BV
Date: 2017
DOI: 10.1016/J.JENVMAN.2016.10.023
Abstract: Concentration of eight heavy metals in surface and groundwater around Dhaka Export Processing Zone (DEPZ) industrial area were investigated, and the health risk posed to local children and adult residents via ingestion and dermal contact was evaluated using deterministic and probabilistic approaches. Metal concentrations (except Cu, Mn, Ni, and Zn) in Bangshi River water were above the drinking water quality guidelines, while in groundwater were less than the recommended limits. Concentration of metals in surface water decreased as a function of distance. Estimations of non-carcinogenic health risk for surface water revealed that mean hazard index (HI) values of As, Cr, Cu, and Pb for combined pathways (i.e., ingestion and dermal contact) were >1.0 for both age groups. The estimated risk mainly came from the ingestion pathway. However, the HI values for all the examined metals in groundwater were <1.0, indicating no possible human health hazard. Deterministically estimated total cancer risk (TCR) via Bangshi River water exceeded the acceptable limit of 1 × 10
Location: Korea, Republic of
Start Date: 2020
End Date: 2023
Funder: NRF
View Funded Activity