ORCID Profile
0000-0001-6561-6293
Current Organisation
Swinburne University of Technology
Does something not look right? The information on this page has been harvested from data sources that may not be up to date. We continue to work with information providers to improve coverage and quality. To report an issue, use the Feedback Form.
Publisher: MDPI AG
Date: 25-02-2023
DOI: 10.3390/MA16051917
Abstract: Ultra-short 230 fs laser pulses of 515 nm wavelength were tightly focused into 700 nm focal spots and utilised in opening ∼400 nm nano-holes in a Cr etch mask that was tens-of-nm thick. The ablation threshold was found to be 2.3 nJ ulse, double that of plain silicon. Nano-holes irradiated with pulse energies below this threshold produced nano-disks, while higher energies produced nano-rings. Both these structures were not removed by either Cr or Si etch solutions. Subtle sub-1 nJ pulse energy control was harnessed to pattern large surface areas with controlled nano-alloying of Si and Cr. This work demonstrates vacuum-free large area patterning of nanolayers by alloying them at distinct locations with sub-diffraction resolution. Such metal masks with nano-hole opening can be used for formation of random patterns of nano-needles with sub-100 nm separation when applied to dry etching of Si.
Publisher: Optica Publishing Group
Date: 16-11-2021
DOI: 10.1364/PRJ.434599
Abstract: Flat lenses thinner than a wavelength promise to replace conventional refractive lenses in miniaturized optical systems. However, Fresnel zone plate flat lens designs require dense annuli, which significantly challenges nanofabrication resolution. Herein, we propose a new implementation of detour phase graphene flat lens with flexible annular number and width. Several graphene metalenses demonstrated that with a flexible selection of the line density and width, the metalenses can achieve the same focal length without significant distortions. This will significantly weaken the requirement of the nanofabrication system which is important for the development of large-scale flat lenses in industry applications.
Publisher: MDPI AG
Date: 06-03-2023
DOI: 10.20944/PREPRINTS202303.0106.V1
Abstract: Microlens arrays (MLAs) which are increasingly popular micro-optical elements in compact integrated optical systems were fabricated by femtosecond direct laser write (fs-DLW) technique in the low-shrinkage SZ2080TM photoresist. High fidelity definition of 3D surfaces on IR transparent CaF2 substrates allowed to achieve & sim 50% transmittance at chemical fingerprinting spectral region 2-5 & mu m wavelengths since MLAs were only & sim 10 & mu m high corresponding to the numerical aperture of 0.3 (the lens height is comparable with the IR wavelength). To combine diffractive and refractive capabilities in miniaturised optical setup, a graphene oxide (GO) grating acting as a linear polariser was also fabricated by fs-DLW by ablation of a 1 & mu m-thick GO thin film. Such an ultra-thin GO polariser can be integrated with the fabricated MLA to add dispersion control at the focal plane. Pairs of MLAs and GO polarisers were characterised throughout visible-IR spectral window and numerical modeling was used to simulate their performance. Good match between experimental results of MLA focusing and simulations was achieved.
Publisher: MDPI AG
Date: 26-02-2023
DOI: 10.3390/MI14030550
Abstract: Ultra-short 230 fs laser pulses of a 515 nm wavelength were tightly focused onto 700 nm focal spots and utilised in opening ∼0.4–1 μm holes in alumina Al2O3 etch masks with a 20–50 nm thickness. Such dielectric masks simplify the fabrication of photonic crystal (PhC) light-trapping patterns for the above-Lambertian performance of high-efficiency solar cells. The conditions of the laser ablation of transparent etch masks and the effects sub-surface Si modifications were revealed by plasma etching, numerical modelling, and minority carrier lifetime measurements. Mask-less patterning of Si is proposed using fs laser direct writing for dry plasma etching of Si.
Publisher: MDPI AG
Date: 20-06-2023
DOI: 10.3390/NANO13121894
Abstract: Herein, we give an overview of several less explored structural and optical characterization techniques useful for biomaterials. New insights into the structure of natural fibers such as spider silk can be gained with minimal s le preparation. Electromagnetic radiation (EMR) over a broad range of wavelengths (from X-ray to THz) provides information of the structure of the material at correspondingly different length scales (nm-to-mm). When the s le features, such as the alignment of certain fibers, cannot be characterized optically, polarization analysis of the optical images can provide further information on feature alignment. The 3D complexity of biological s les necessitates that there be feature measurements and characterization over a large range of length scales. We discuss the issue of characterizing complex shapes by analysis of the link between the color and structure of spider scales and silk. For ex le, it is shown that the green-blue color of a spider scale is dominated by the chitin slab’s Fabry–Pérot-type reflectivity rather than the surface nanostructure. The use of a chromaticity plot simplifies complex spectra and enables quantification of the apparent colors. All the experimental data presented herein are used to support the discussion on the structure–color link in the characterization of materials.
Publisher: MDPI AG
Date: 15-11-2022
DOI: 10.3390/MA15228063
Abstract: The controlled deposition of CoCrFeNiMo0.2 high-entropy alloy (HEA) microparticles was achieved by using laser-induced forward transfer (LIFT). Ultra-short laser pulses of 230 fs of 515 nm wavelength were tightly focused into ∼2.4 μm focal spots on the ∼50-nm thick plasma-sputtered films of CoCrFeNiMo0.2. The morphology of HEA microparticles can be controlled at different fluences. The HEA films were transferred onto glass substrates by magnetron sputtering in a vacuum (10−8 atm) from the thermal spray-coated substrates. The absorption coefficient of CoCrFeNiMo0.2α≈6×105 cm−1 was determined at 600-nm wavelength. The real and imaginary parts of the refractive index (n+iκ) of HEA were determined from reflectance and transmittance by using nanofilms.
Publisher: MDPI AG
Date: 25-07-2022
DOI: 10.3390/MI13081170
Abstract: THz band-pass filters were fabricated by femtosecond-laser ablation of 25-μm-thick micro-foils of stainless steel and Kapton film, which were subsequently metal coated with a ∼70 nm film, closely matching the skin depth at the used THz spectral window. Their spectral performance was tested in transmission and reflection modes at the Australian Synchrotron’s THz beamline. A 25-μm-thick Kapton film performed as a Fabry–Pérot etalon with a free spectral range (FSR) of 119 cm−1, high finesse Fc≈17, and was tuneable over ∼10μm (at ∼5 THz band) with β=30∘ tilt. The structure of the THz beam focal region as extracted by the first mirror (slit) showed a complex dependence of polarisation, wavelength and position across the beam. This is important for polarisation-sensitive measurements (in both transmission and reflection) and requires normalisation at each orientation of linear polarisation.
Publisher: MDPI AG
Date: 31-03-2023
DOI: 10.3390/MI14040798
Abstract: Microlens arrays (MLAs) which are increasingly popular micro-optical elements in compact integrated optical systems were fabricated using a femtosecond direct laser write (fs-DLW) technique in the low-shrinkage SZ2080TM photoresist. High-fidelity definition of 3D surfaces on IR transparent CaF2 substrates allowed to achieve ∼50% transmittance in the chemical fingerprinting spectral region 2–5 μm wavelengths since MLAs were only ∼10 μm high corresponding to the numerical aperture of 0.3 (the lens height is comparable with the IR wavelength). To combine diffractive and refractive capabilities in miniaturised optical setup, a graphene oxide (GO) grating acting as a linear polariser was also fabricated by fs-DLW by ablation of a 1 μm-thick GO thin film. Such an ultra-thin GO polariser can be integrated with the fabricated MLA to add dispersion control at the focal plane. Pairs of MLAs and GO polarisers were characterised throughout the visible–IR spectral window and numerical modelling was used to simulate their performance. A good match between the experimental results of MLA focusing and simulations was achieved.
Publisher: MDPI AG
Date: 04-05-2023
DOI: 10.20944/PREPRINTS202305.0246.V1
Abstract: In this perspective, we give an overview of several less explored structural and optical characterisation techniques useful for biomaterials. New insights into the structure of natural fibres such as spider silk can be gained with minimal s le preparation. Electromagnetic radiation (EMR) over a broad range of wavelengths (from X-ray to THz) provides information of the structure of the material at cor- respondingly different length scales (nm-to-mm). When the s le features, such as the alignment of certain fibres, cannot be characterised optically, polarisation analysis of the optical images can provide further information on feature alignment. The 3D complexity of biological s les necessitates that there be feature measure- ments and characterisation over a large range of length scales. We discuss the issue of characterising complex shapes by analysis of the link between the color and struc- ture of spider scales and silk. For ex le, it is shown that the green-blue color of a spider scale is dominated by the chitin slab& rsquo s Fabry-P ́erot type reflectivity rather than the surface nanostructure. The use of a chromaticity plot simplifies complex spectra and enables quantification of the apparent colors. All the experimental data presented herein are used to support the discussion on the structure-color link in the characterisation of materials.
Publisher: Elsevier BV
Date: 12-2023
No related grants have been discovered for Haoran Mu.