ORCID Profile
0000-0002-3890-7105
Current Organisations
Norges teknisk-naturvitenskapelige universitet
,
Massey University
Does something not look right? The information on this page has been harvested from data sources that may not be up to date. We continue to work with information providers to improve coverage and quality. To report an issue, use the Feedback Form.
Publisher: Hindawi Limited
Date: 2014
DOI: 10.1155/2014/189197
Abstract: Bovine pericardium is used for heart valve leaflet replacement where the strength and thinness are critical properties. Pericardium from neonatal animals (4–7 days old) is advantageously thinner and is considered as an alternative to that from adult animals. Here, the structures of adult and neonatal bovine pericardium tissues fixed with glutaraldehyde are characterized by synchrotron-based small angle X-ray scattering (SAXS) and compared with the mechanical properties of these materials. Significant differences are observed between adult and neonatal tissue. The glutaraldehyde fixed neonatal tissue has a higher modulus of elasticity (83.7 MPa) than adult pericardium (33.5 MPa) and a higher normalised ultimate tensile strength (32.9 MPa) than adult pericardium (19.1 MPa). Measured edge on to the tissue, the collagen in neonatal pericardium is significantly more aligned (orientation index (OI) 0.78) than that in adult pericardium (OI 0.62). There is no difference in the fibril diameter between neonatal and adult pericardium. It is shown that high alignment in the plane of the tissue provides the mechanism for the increased strength of the neonatal material. The superior strength of neonatal compared with adult tissue supports the use of neonatal bovine pericardium in heterografts.
Publisher: American Chemical Society (ACS)
Date: 28-04-2022
Publisher: MDPI AG
Date: 23-07-2022
Abstract: Thin, strong scaffold materials are needed for surgical applications. New materials are required, particularly those readily available, such as from non-human sources. Bovine amniotic membrane (antepartum) and equine amniotic membrane (postpartum) were characterized with tear and tensile tests. The structural arrangement of the collagen fibrils was determined by small-angle X-ray scattering, scanning electron microscopy, and ultrasonic imaging. Bovine amnion had a thickness-normalized tear strength of 12.6 (3.8) N/mm, while equine amnion was 14.8 (5.3) N/mm. SAXS analysis of the collagen fibril arrangement yielded an orientation index of 0.587 (0.06) and 0.681 (0.05) for bovine and equine, respectively. This may indicate a relationship between more highly aligned collagen fibrils and greater strength, as seen in other materials. Amnion from bovine or equine sources are strong, thin, elastic materials, although weaker than other collagen tissue materials commonly used, that may find application in surgery as an alternative to material from human donors.
Publisher: Wiley
Date: 13-02-2017
DOI: 10.1002/JSFA.8199
Abstract: Deer leather has a characteristic pattern, referred to as 'pebble', which is accorded such importance that a lack of it renders a leather defective. Synchrotron-based small-angle X-ray scattering (SAXS), ultrasonic imaging, scanning electron microscopy, and tear tests were used to investigate the structural characteristics of well-pebbled and poorly pebbled cervine leathers. Poorly pebbled leather has a less open structure in the upper grain region than well-pebbled leather. The orientation index (OI) of leather with a poor pebble is less than that of the well-pebbled leather, particularly in the corium. The tear strength is also less for the poorly pebbled leather. The differences in structure between well- and poorly pebbled cervine leathers are not the same as the structural differences between tight and loose bovine leathers, to which they are sometimes compared. On the contrary, good pebble may reflect an internal structure similar to that of looseness. It is hoped that methods to prevent a reduction in pebbling during the processing of cervine leather may be developed by applying this knowledge of cervine leather's structural characteristics. © 2017 Society of Chemical Industry.
Bovine Meniscus Middle Zone Tissue: Measurement of Collagen Fibril Behavior During Compression
Publisher: Informa UK Limited
Date: 07-2020
DOI: 10.2147/IJN.S261298
Publisher: Elsevier BV
Date: 12-2018
Publisher: American Chemical Society (ACS)
Date: 17-01-2013
DOI: 10.1021/JF3043067
Abstract: Collagen is the main structural component of leather, skin, and some other applications such as medical scaffolds. All of these materials have a mechanical function, so the manner in which collagen provides them with their strength is of fundamental importance and was investigated here. This study shows that the tear strength of leather across seven species of mammals depends on the degree to which collagen fibrils are aligned in the plane of the tissue. Tear-resistant material has the fibrils contained within parallel planes with little crossover between the top and bottom surfaces. The fibril orientation is observed using small-angle X-ray scattering in leather, produced from skin, with tear strengths (normalized for thickness) of 20-110 N/mm. The orientation index, 0.420-0.633, is linearly related to tear strength such that greater alignment within the plane of the tissue results in stronger material. The statistical confidence and ersity of animals suggest that this is a fundamental determinant of strength in tissue. This insight is valuable in understanding the performance of leather and skin in biological and industrial applications.
Publisher: Royal Society of Chemistry (RSC)
Date: 2017
DOI: 10.1039/C7RA05560A
Abstract: Water, lanolin and Lipsol interact with collagen to alter the structure at the fibrillar scale.
Publisher: American Chemical Society (ACS)
Date: 25-02-2015
DOI: 10.1021/JF506357J
Abstract: As hides and skins are processed to produce leather, chemical and physical changes take place that affect the strength and other physical properties of the material. The structural basis of these changes at the level of the collagen fibrils is not fully understood and forms the basis of this investigation. Synchrotron-based small-angle X-ray scattering (SAXS) is used to quantify fibril orientation and D-spacing through eight stages of processing from fresh green ovine skins to staked dry crust leather. Both the D-spacing and fibril orientation change with processing. The changes in thickness of the leather during processing affect the fibril orientation index (OI) and account for much of the OI differences between process stages. After thickness is accounted for, the main difference in OI is due to the hydration state of the material, with dry materials being less oriented than wet. Similarly significant differences in D-spacing are found at different process stages. These are due also to the moisture content, with dry s les having a smaller D-spacing. This understanding is useful for relating structural changes that occur during different stages of processing to the development of the final physical characteristics of leather.
Publisher: American Chemical Society (ACS)
Date: 05-09-2017
Publisher: American Scientific Publishers
Date: 12-2016
Publisher: Elsevier BV
Date: 2006
DOI: 10.1016/J.WATRES.2005.11.002
Abstract: Active filters, which facilitate phosphorus (P) removal via precipitation and/or adsorption, offer a promising 'appropriate technology' for upgrading small wastewater treatment systems. Research on active filters for P removal using steel slag material has been conducted in laboratories across the world, however, field experiments have been limited and long-term data is practically non-existent. This paper presents a decade of experience on P removal by active slag filters at a full-scale treatment plant. During 1993-1994 the filter removed 77% of the total phosphorus (TP), and over the first 5 years of the filter's operation it reduced the mean effluent TP concentration to 2.3 mgl(-1). However during the sixth year of operation P removal was significantly reduced. Over the 11 years of monitoring, 22.4 tonnes of TP was removed by the filter, 19.7 tonnes of this in the first 5-year period. It was determined that the slag material maintained its maximum removal potential until reaching a P-retention ratio of 1.23 kg TP per tonne of slag. This paper provides the first long-term field data for slag filters, and shows that they can provide P removal for a half a decade before filter replacement/rejuvenation is required.
Publisher: Springer Science and Business Media LLC
Date: 04-09-2019
Publisher: AIP Publishing
Date: 26-01-2015
DOI: 10.1063/1.4906325
Abstract: Type I collagen is the main structural component of skin, tendons, and skin products, such as leather. Understanding the mechanical performance of collagen fibrils is important for understanding the mechanical performance of the tissues that they make up, while the mechanical properties of bulk tissue are well characterized, less is known about the mechanical behavior of in idual collagen fibrils. In this study, bovine pericardium is subjected to strain while small angle X-ray scattering (SAXS) patterns are recorded using synchrotron radiation. The change in d-spacing, which is a measure of fibril extension, and the change in fibril diameter are determined from SAXS. The tissue is strained 0.25 (25%) with a corresponding strain in the collagen fibrils of 0.045 observed. The ratio of collagen fibril width contraction to length extension, or the Poisson's ratio, is 2.1 ± 0.7 for a tissue strain from 0 to 0.25. This Poisson's ratio indicates that the volume of in idual collagen fibrils decreases with increasing strain, which is quite unlike most engineering materials. This high Poisson's ratio of in idual fibrils may contribute to high Poisson's ratio observed for tissues, contributing to some of the remarkable properties of collagen-based materials.
Publisher: Informa UK Limited
Date: 07-2011
DOI: 10.1080/09593330.2010.525749
Abstract: Active slag filters are an emerging technology for removing phosphorus (P) from wastewaters. Recent research revealed that adsorption onto Fe oxides/oxyhydroxides at near-neutral pH and oxidizing Eh is the key mechanism of P removal by melter slag filters. Currently, filter lifespan is limited by available adsorption sites. This study examined whether the performance and longevity of active filters could be improved via chemical treatment to create additional reactive sites as well as regenerate exhausted ones. Fresh original melter slag as well as slag from an exhausted full-scale filter was tested. Chemical reagents that could manipulate the pH/Eh of the slag granule surfaces and potentially activate them for further P removal were used, namely hydrochloric acid (HCI), sodium hydroxide (NaOH) and sodium dithionite (Na2S2O4). Waste stabilization pond effluent was then applied to the treated slag to assess the effectiveness of the treatments at improving P removal. Fresh slag treated with Na2S204 and HCl, respectively, retained 1.9 and 1.4 times more P from the effluent than the untreated fresh slag. These reagents were even more effective at regenerating the exhausted slag, increasing total retained P by a factor of 13 and six, respectively, compared with untreated slag. Sodium hydroxide was ineffective at increasing P removal. The higher P retention by the 'treated exhausted slag' compared with the 'treated fresh media' indicates that adsorption sites on melter slag filters become increasingly reactive with time. This research is the first study to provide evidence that P retention by active slag filters can be increased by both (1) chemical pre treatment and (2) chemical post-treatment once their P removal is exhausted, thereby potentially transforming them from a single use system to a more viable, reusable treatment technology.
Publisher: American Chemical Society (ACS)
Date: 10-09-2015
Publisher: American Chemical Society (ACS)
Date: 04-08-2022
Publisher: Elsevier BV
Date: 02-2019
DOI: 10.1016/J.JMBBM.2018.10.004
Abstract: Applications for skin derived collagen materials, such as leather and acellular dermal matrices, usually require both strength and flexibility. In general, both the tensile modulus (which has an impact on flexibility) and strength are known to increase with fiber alignment, in the tensile direction, for practically all collagen-based tissues. The structural basis for flexibility in leather was investigated and the moisture content was varied. Small angle X-ray scattering was used to determine collagen fibril orientation, elongation and lateral intermolecular spacing in leather conditioned by different controlled humidity environments. Flexibility was measured by a three point bending test. Leather was prepared by tanning under biaxial loading to create leather with increased fibril alignment and thus strength, but this treatment also increased the stiffness. As collagen aligns, it not only strengthens the material but it also stiffens because tensile loading is then applied along the covalent chain of the collagen molecules, rather than at an angle to it. Here it has been shown that with higher moisture content greater flexibility of the material develops as water absorption inside collagen fibrils produces a larger lateral spacing between collagen molecules. It is suggested that water provides a lubricating effect in collagen fibrils, enabling greater freedom of movement and therefore greater flexibility. When collagen molecules align in the strain direction during tanning, leather stiffens not only by the fiber alignment itself but also because collagen molecules pack closer together, reducing the ability of the molecules to move relative to each other.
Publisher: Elsevier BV
Date: 03-2018
DOI: 10.1016/J.JMBBM.2017.12.009
Abstract: Acellular dermal matrix (ADM) materials are used as scaffold materials in reconstructive surgery. The internal structural response of these materials in load-bearing clinical applications is not well understood. Bovine ADM is characterized by small-angle X-ray scattering while subjected to strain. Changes in collagen fibril orientation (O), degree of orientation as an orientation index (OI) (measured both edge-on and flat-on to the ADM), extension (from d-spacing changes) and changes to intermolecular spacing are measured as a result of the strain and stress in conjunction with mechanical measurements. As is already well established in similar systems, when strained, collagen fibrils in ADM can accommodate the strain by reorienting by up to 50° (as an average of all the fibrils). This reorientation corresponds to the OI increasing from 0.3 to 0.7. Here it is shown that concurrently, the intermolecular spacing between tropocollagen decreases by 10% from 15.8 to 14.3Å, with the fibril diameter decreasing from 400 to 375Å, and the in idual fibrils extending by an average of 3.1% (D-spacing from 63.9 to 65.9nm). ADM materials can withstand large strain and high stress due to the combined mechanisms of collagen reorientation, in idual fibril extension, sliding and changes in the molecular packing density.
Publisher: Elsevier BV
Date: 09-2022
DOI: 10.1016/J.IJBIOMAC.2022.06.180
Abstract: Type I collagen is a ubiquitous structural protein in animal tissues. It is normally present in a hydrated form. However, collagen is very dependent on associated water for its mechanical properties. In skin, where type I collagen is dominant, there is a longstanding concern that the skin and therefore collagen may partially dry out and result in structural degradation. Here we show that dehydration of type I collagen fibrils, using 2-propanol, results in a two-stage dehydration process. Initially, the fibrils do not change length, i.e. the D-period remains constant, but shrinkage occurs within the fibrils by an increase in the gap region and a decrease in the overlap region within a D-band and a shortening of the helical turn distance and fibril diameter. Only with further dehydration does the length of the collagen fibril decrease (a decrease in D-period). This mechanism explains why collagen materials are resistant to gross structural change in the early stages of dehydration and shows why they may then suffer from sudden external shrinkage with further dehydration.
Publisher: American Chemical Society (ACS)
Date: 04-04-2007
DOI: 10.1021/ES062496B
Abstract: Phosphorus (P) removal mechanisms from waste stabilization pond effluent by a melter slag filter were investigated. The studied filter had treated pond effluent for a decade, but lost its P removal efficiency after 5 years. The P distribution in the slag was examined by scanning electron microscopy (SEM), electron dispersive spectrometry (EDS), X-ray fluorescence (XRF), X-ray diffraction (XRD), and chemical fractionation. The results showed the slag to be covered by a film comprising metal oxides/oxyhydroxides, organic resin, and Fe-phosphate precipitates. The slag porous matrix beneath this film hosted lower P concentrations and consisted of metal oxides/oxyhydroxides and calcmagnesium silicates. The study revealed the following mechanisms for P removal from effluent by the melter slag: (1) P adsorption onto metal oxides/oxyhydroxides which are ubiquitous throughout the porous slag matrix and its surface film (2) P precipitation, mainly as Fe-phosphates (determined by SEM/EDS) on the surface film, derived from the release of metal ions into the solution phase and (3) P sequestration by an amorphous organic resin that comprises a substantial proportion of the surface film, which was deduced by SEM/EDS and XRF. Results of chemical extractions performed on the slag demonstrated that 1 M HCl, which has been used to determine Ca-associated P in previous studies, is an unreliable Ca-P marker. By contrast, the citrate-dithionite reagent was shown to be a good indicator of Fe/Al-associated P and revealed that adsorption onto metal oxides/oxyhydroxides, in the porous matrix as well as its surface film, is the most significant P removal mechanism achieved by the slag filter.
Publisher: Royal Society of Chemistry (RSC)
Date: 2015
DOI: 10.1039/C4RA10658J
Abstract: Cross linking was found to be a factor in collagen fibril alignment in pericardium tissue.
Publisher: American Chemical Society (ACS)
Date: 13-09-2017
Publisher: Elsevier BV
Date: 02-2009
DOI: 10.1016/J.WATRES.2008.10.020
Abstract: Active slag filters are an emerging technology for removing phosphorus (P) from wastewater. Currently, the lifespan of these filters is limited by their available reactive sites. An increasing number of researchers suggest that drying active filters can renew their P removal capacity, although there has only been one research paper that has achieved regeneration. Hence, this study investigated techniques to regenerate the P removal efficiency of exhausted melter slag filter media which had successfully treated effluent for 5 years in the field before becoming inactive. Several techniques were performed to expose fresh surface sites on the slag, including: (1) drying (2) agitation and (3) crushing of the slag granules. Crushing resulted in the best regeneration of P removal efficiency by the slag, however, after just 2 months the renewed P removal efficiency of the crushed slag fell back to a similar level to that exhibited by exhausted slag. Furthermore, none of the other physical methods caused long-term rejuvenation of the exhausted slag to remove P from effluent. Scanning electron microscopy revealed that none of the regeneration techniques exposed substantial new phosphorus adsorption sites on the slag granules. These findings therefore challenge the validity of the existing dogma that active slag filters can be effectively regenerated by simple physical treatments, indicating further research is required to optimise active filter performance.
Publisher: American Chemical Society (ACS)
Date: 17-08-2007
DOI: 10.1021/ES070914M
Abstract: The release of phosphorus (P) and iron (Fe) from a melter slag filter in solutions of varying Eh and pH was examined. The filter had been removing P from waste stabilization pond effluent for several years. The study revealed that the highest P (95% of total P) and Fe (25% of total Fe) release from the slag occurred in the solution with the lowest Eh (-400 mV, relative to the standard hydrogen electrode, SHE) and lowest pH (4.9). Solutions with high pH (9.1) also proved favorable for P release (20 to 40% of total P) from the slag, at both reducing (-400 mV) and oxidizing (+300 mV) Eh. By contrast, solutions with pH 4.9 and 6.7 and oxidizing Eh (+300 mV) liberated the lowest P and Fe contents into the aqueous phase (<1% for both elements). The findings showed that Eh and pH are important parameters affecting P release from slag filters. At low Eh and low pH, P is released due to the dissolution of Fe oxides/oxyhydroxides, as supported by scanning electron microscopy (SEM)/energy dispersive spectrometry (EDS). At high pH, P is desorbed from negatively charged Fe oxide/oxyhydroxide surfaces. The results of this investigation are pertinentto the design and operation of melter slag filters that treat all forms of P-rich waters, such as wastewater, stormwater, and farm runoff. The study demonstrated that P retention by melter slag filters is optimal in water bodies characterized by near-neutral pH and oxidizing Eh because these conditions favor P adsorption onto Fe oxides/oxyhydroxides.
Publisher: Springer Science and Business Media LLC
Date: 09-01-2009
DOI: 10.1007/S00249-008-0399-4
Abstract: In this paper, we model the mechanics of a collagen pair in the connective tissue extracellular matrix that exists in abundance throughout animals, including the human body. This connective tissue comprises repeated units of two main structures, namely collagens as well as axial, parallel and regular anionic glycosaminoglycan between collagens. The collagen fibril can be modeled by Hooke's law whereas anionic glycosaminoglycan behaves more like a rubber-band rod and as such can be better modeled by the worm-like chain model. While both computer simulations and continuum mechanics models have been investigated for the behavior of this connective tissue typically, authors either assume a simple form of the molecular potential energy or entirely ignore the microscopic structure of the connective tissue. Here, we apply basic physical methodologies and simple applied mathematical modeling techniques to describe the collagen pair quantitatively. We found that the growth of fibrils was intimately related to the maximum length of the anionic glycosaminoglycan and the relative displacement of two adjacent fibrils, which in return was closely related to the effectiveness of anionic glycosaminoglycan in transmitting forces between fibrils. These reveal the importance of the anionic glycosaminoglycan in maintaining the structural shape of the connective tissue extracellular matrix and eventually the shape modulus of human tissues. We also found that some macroscopic properties, like the maximum molecular energy and the breaking fraction of the collagen, were also related to the microscopic characteristics of the anionic glycosaminoglycan.
Publisher: Elsevier BV
Date: 11-2018
Publisher: American Chemical Society (ACS)
Date: 16-06-2014
DOI: 10.1021/SC500212R
Publisher: Elsevier BV
Date: 02-2010
DOI: 10.1016/J.JTBI.2009.10.009
Abstract: Stiff polymers, such as single-stranded DNA, unstructured RNA and cellulose, are all basically extremely long rods with relatively short repeating monomers. The simplest model for describing such stiff polymers is called the freely jointed chain model, which treats a molecule as a chain of perfectly rigid subunits of orientationally independent statistical segments, joined together by perfectly flexible hinges. A more realistic model that incorporates the entropic elasticity of a molecule, called the worm-like chain model, has been proposed by assuming that each monomer resists the bending force. Some force-extension formulae for the worm-like chain model have been previously found in terms of interpolation and numerical solutions resulting from statistical mechanics. In this paper, however, we adopt a variational principle to seek the minimum energy configuration of a stretched molecule by incorporating all the possible orientations of each monomer under thermal equilibrium, i.e., constant temperature. We determine a force-extension formula for the worm-like chain model analytically. We find that our formula suggests new terms such as the free energy and the cut-off force of a molecule, which define a clear transition from the entropic regime to the enthalpic regime and the fracture of the molecule, respectively. In addition, we predict two possible phase changes for a stretched molecule, i.e., from a super-helix to a soliton and then from a soliton to a vertical twisted line. We show theoretically that a molecule must undergo at least one phase change before it is fully stretched into its total contour length. This new formula is used to fit recent experimental data and shows a good agreement with some current literature that uses a statistical approach. Finally, an instability analysis is adopted to investigate the sensitivity of the new formula subject to small changes in temperature.
Publisher: Elsevier BV
Date: 08-2022
Publisher: Wiley
Date: 20-02-2018
DOI: 10.1002/JSFA.8863
Abstract: Ovine leather has around half the tear strength of bovine leather and is therefore not suitable for high-value applications such as shoes. Tear strength has been correlated with the natural collagen fibril alignment (orientation index, OI). It is hypothesized that it could be possible to artificially increase the OI of the collagen fibrils and that an artificial increase in OI could increase tear strength. Ovine skins, after pickling and bating, were strained biaxially during chrome tanning. The strain ranged from 2 to 15% of the initial s le length, either uniformly in both directions by 10% or with 3% in one direction and 15% in the other. Once tanned, the leather tear strengths were measured and the collagen fibril orientation was measured using synchrotron-based small-angle X-ray scattering. The OI increased as a result of strain during tanning from 0.48 to 0.79 (P = 0.001) measured edge-on and the thickness-normalized tear strength increased from 27 to 43 N mm
Publisher: SAGE Publications
Date: 02-08-2018
Abstract: The authors used microscopy and synchrotron-based small-angle X-ray scattering analysis (SAXS) to describe lesions macroscopically typical of tropical keratopathy (“Florida spots”) from 6 cats on St Kitts. Microscopically, there were varying degrees of epithelial hyperplasia and thinning of the cornea (by 4% to 18%) due to loss of corneal stroma associated with dense accumulations of collagen in the superficial stroma. The collagen fibrils in lesions were wider and had more variable diameters (39.5 ± 5.0 nm, mean ± SD) than in normal corneas (25.9 ± 3.6 nm P .01). There were occasional vacuoles ( μm) in the corneal epithelial basement membrane but no evidence of inflammation, edema, stromal neovascularization, fibrosis, acid-fast organisms, or structures suggestive of a fungal organism. SAXS analysis showed collagen fibril diameters and variation in size were greater in stroma containing the lesions compared to normal corneas (48.8 ± 4.5 nm vs 35.5 ± 2.6 P .05). The d-spacing of collagen in the stroma of lesions and normal corneas was the same, but the average orientation index of collagen in lesions was greater (0.428 ± 0.08 vs 0.285 ± 0.03 P .05). A survey revealed Florida spots lesions were static over time and became less obvious in only 1 of 6 affected cats adopted on St Kitts and taken to areas in the US where lesions are not reported. An anterior stromal collagen disorder with various degrees of epithelial hyperplasia is the pathologic hallmark of lesions clinically identical to Florida spots in cats from St Kitts.
Publisher: Elsevier BV
Date: 09-2019
DOI: 10.1016/J.IJBIOMAC.2019.07.061
Abstract: Arteries are elastic structures containing both elastin and collagen. While the high content of elastin is understood to be important for the elasticity of arteries with systolic and diastolic pressure pulses, the role of collagen in the elastic properties of arteries is less understood. Here we use small angle X-ray scattering to investigate the changes in arrangement of collagen fibrils and the strain experienced by collagen fibrils as arteries are inflated. Collagen fibrils re-orient to become more aligned in both the annular direction and radially as arteries inflate. With arterial pressures up to 32 kPa there is no observable increase in D-spacing of the collagen fibrils ( 6%. In arteries the collagen fibril elasticity (strain at the scale of fibrils) is not the main elastic component of the arterial walls. This indicates that wall elasticity is dominated by other factors such as the structural arrangement of the collagen fibers.
Location: United States of America
Location: New Zealand
No related grants have been discovered for Richard Haverkamp.