ORCID Profile
0000-0002-5306-6869
Current Organisation
University of South Australia
Does something not look right? The information on this page has been harvested from data sources that may not be up to date. We continue to work with information providers to improve coverage and quality. To report an issue, use the Feedback Form.
Publisher: Springer Science and Business Media LLC
Date: 08-08-2017
DOI: 10.1038/S41598-017-07531-Y
Abstract: A practical fabrication technique is presented to tackle the trade-off between the water flux and salt rejection of thin film composite (TFC) reverse osmosis (RO) membranes through controlled creation of a thinner active selective polyamide (PA) layer. The new thin film nano-composite (TFNC) RO membranes were synthesized with multifunctional poly tannic acid-functionalized graphene oxide nanosheets (pTA-f-GO) embedded in its PA thin active layer, which is produced through interfacial polymerization. The incorporation of pTA-f-GOL into the fabricated TFNC membranes resulted in a thinner PA layer with lower roughness and higher hydrophilicity compared to pristine membrane. These properties enhanced both the membrane water flux (improved by 40%) and salt rejection (increased by 8%) of the TFNC membrane. Furthermore, the incorporation of biocidal pTA-f-GO nanosheets into the PA active layer contributed to improving the antibacterial properties by 80%, compared to pristine membrane. The fabrication of the pTA-f-GO nanosheets embedded in the PA layer presented in this study is a very practical, scalable and generic process that can potentially be applied in different types of separation membranes resulting in less energy consumption, increased cost-efficiency and improved performance.
Publisher: Oxford University Press (OUP)
Date: 12-07-2013
Publisher: American Chemical Society (ACS)
Date: 30-07-2013
DOI: 10.1021/LA401987Y
Abstract: A series of novel hiphiles were designed for self-assembly into chiral morphologies, the hiphiles consisting of a glutamic acid (Glu) headgroup connected through an 11-carbon alkoxy chain to a diphenyldiazenyl (Azo) group and terminated with a variable length alkyl chain (R-Azo-11-Glu, where R denotes the number of carbons in the distal chain). TEM imaging of hiphile aggregates self-assembled from heated, methanolic, aqueous solution showed that chiral order, expressed as twisted ribbons, helical ribbons, and helically based nanotubes, increased progressively up to a distal chain length containing eight carbons, and then decreased with further increases in distal chain length. TEM and CD showed that the chiral aggregations of single enantiomers were influenced by the molecular chirality of the headgroup. However, the assembly of D,L-10-Azo-11-Glu into nanotubes demonstrated that chiral symmetry breaking effected by the azo group was also relevant to the chiral organization of the hiphiles. The chiral order of aggregate morphologies was additionally affected by the temperature and solvent composition of assembly in a manner correlated to the mechanism driving assembly i.e., D,L-10-Azo-11-Glu was sensitive to the temperature of assembly but less so to solvent composition, while L-14-Azo-11-Glu was sensitive to solvent composition and not to temperature. FTIR and UV-vis spectroscopic investigations into the organization of the head and azo groups, in chiral and achiral structures, illustrated that a balance of the influences of the hydrophilic and hydrophobic components on self-assembly was required for the optimization of the chiral organization of the self-assembled structures.
Publisher: American Chemical Society (ACS)
Date: 26-09-2012
DOI: 10.1021/LA3030606
Abstract: Four hiphiles with L-aspartic acid headgroups (Asp) and a diphenyldiazenyl group (Azo) contained within the hydrophobic tails were designed and synthesized for self-assembly into helically based nanotubes. The hiphiles of the form R'-{4-[(4-alkylphenyl)diazenyl]phenoxy}alkanoyl-L-aspartic acid (where R' is 10 or 11) varied only in alkyl chain lengths either side of the azo group, having 4, 7, or 10 carbon distal chains and 10 or 11 carbon proximal chains (R-Azo-R'-Asp, where R denotes the number of carbons in the distal chain and R' denotes the number of carbons in the proximal chain). Despite the molecular similarities, distinct differences were identified in the chiral order of the structures self-assembled from hot methanolic aqueous solutions using microscopy and spectroscopic analyses. This was reflected in dominant thermodynamic aggregate morphologies that ranged from amorphous material for 10-Azo-10-Asp, through twisted ribbons (196 ± 49 nm pitch) for 7-Azo-11-Asp, to the desired helically based nanotubes for 4- and 7-Azo-10-Asp (81 ± 11 and 76 ± 6 nm diameters, respectively). Another key variable in the self-assembly of the hiphiles was the use of a second method to precipitate aggregates from solution at room temperature. This method enabled the isolation of thermodynamically unstable and key transitional structures. Helical ribbons were precursor structures to the nanotubes formed from 4- and 7-Azo-10-Asp as well as the wide, flattened nanotube structures (587 ± 85 nm width) found for 4-Azo-10-Asp. Overall, the results highlighted the interplay of influence of the headgroup and the hydrophobic tail on self-assembly, providing a basis for future rational design of self-assembling hiphiles.
Publisher: Springer Science and Business Media LLC
Date: 28-01-2011
DOI: 10.1557/JMR.2010.3
Publisher: Royal Society of Chemistry (RSC)
Date: 2015
DOI: 10.1039/C5RA09370H
Abstract: The use of a polydopamine-based macroinitiator provides a flexible attachment method that is virtually independent of membrane substrate. The subsequent ARGET-ATRP controllably grafts the stable biofouling resistant polyzwitterion coating.
Publisher: American Chemical Society (ACS)
Date: 07-10-2014
DOI: 10.1021/CR400085M
Publisher: Elsevier BV
Date: 2014
Publisher: MDPI AG
Date: 06-11-2019
DOI: 10.3390/PHARMACEUTICS11110581
Abstract: Delta inulin, also known as microparticulate inulin (MPI), was modified by covalently attaching doxorubicin to its nanostructured surface for use as a targeted drug delivery vehicle. MPI is readily endocytosed by monocytes, macrophages, and dendritic cells and in this study, we sought to utilize this property to develop a system to target anti-cancer drugs to lymphoid organs. We investigated, therefore, whether MPI could be used as a vehicle to deliver doxorubicin selectively, thereby reducing the toxicity of this antibiotic anthracycline drug. Doxorubicin was covalently attached to the surface of MPI using an acid–labile linkage to enable pH-controlled release. The MPI-doxorubicin conjugate was characterized using FTIR and SEM, confirming covalent attachment and indicating doxorubicin coupling had no obvious impact on the physical nanostructure, integrity, and cellular uptake of the MPI particles. To simulate the stability of the MPI-doxorubicin in vivo, it was stored in artificial lysosomal fluid (ALF, pH 4.5). Although the MPI-doxorubicin particles were still visible after 165 days in ALF, 53% of glycosidic bonds in the inulin particles were hydrolyzed within 12 days in ALF, reflected by the release of free glucose into solution. By contrast, the fructosidic bonds were much more stable. Drug release studies of the MPI-doxorubicin in vitro, demonstrated a successful pH-dependent controlled release effect. Confocal laser scanning microscopy studies and flow cytometric analysis confirmed that when incubated with live cells, MPI-doxorubicin was efficiently internalized by immune cells. An assay of cell metabolic activity demonstrated that the MPI carrier alone had no toxic effects on RAW 264.7 murine monocyte/macrophage-like cells, but exhibited anti-cancer effects against HCT116 human colon cancer cells. MPI-doxorubicin had a greater anti-cancer cell effect than free doxorubicin, particularly when at lower concentrations, suggesting a drug-sparing effect. This study establishes that MPI can be successfully modified with doxorubicin for chemotherapeutic drug delivery.
Publisher: MDPI AG
Date: 05-2020
Abstract: This paper reports the oxidation of inulin using varying ratios of sodium periodate and the characterization of the inulin polyaldehyde. The physicochemical properties of the inulin polyaldehyde (oxidized inulin) were characterized using different techniques including 1D NMR spectroscopy, 13C Nuclear magnetic resonance (NMR), Fourier transform infrared spectroscopy (FTIR), thermal gravimetric analysis (TGA), differential scanning calorimetric (DSC), ultraviolet-visible spectroscopy (UV), and scanning electron microscopy (SEM). The aldehyde peak was not very visible in the FTIR, because the aldehyde functional group exists in a masked form (hemiacetal). The thermal stability of the oxidized inulin decreased with the increasing oxidation degree. The smooth spherical shape of raw inulin was destructed due to the oxidation, as confirmed by the SEM result. The 1HNMR results show some new peaks from 4.8 to 5.0 as well as around 5.63 ppm. However, no aldehyde peak was found around 9.7 ppm. This can be attributed to the hemiacetal. The reaction of oxidized inulin with tert-butyl carbazate produced a carbazone conjugate. There was clear evidence of decreased peak intensity for the proton belonging to the hemiacetal group. This clearly shows that not all of the hemiacetal group can be reverted by carbazate. In conclusion, this work provides vital information as regards changes in the physicochemical properties of the oxidized inulin, which has direct implications when considering the further utilization of this biomaterial.
Publisher: Elsevier BV
Date: 2019
Publisher: Elsevier BV
Date: 08-2017
DOI: 10.1016/J.VACCINE.2017.06.045
Abstract: Insoluble, nanostructured delta inulin particles enhance the immunogenicity of co-administered protein antigens and consequently are used as a vaccine adjuvant (Advax™). To better understand their immunomodulatory properties, the in vitro hydrolysis and in vivo distribution of delta inulin particles were investigated. Delta inulin particle hydrolysis under bio-relevant acidic conditions resulted in no observable change to the bulk morphology using SEM, and HPLC results showed that only 6.1% of the inulin was hydrolysed over 21days. However, 65% of the terminal glucose groups were released, showing that acid hydrolysis relatively rapidly releases surface bound chemistries. This was used to explain in vivo biodistribution results in which delta inulin particles surface-labelled with fluorescein-5-thiosemicabizide were administered to mice using intramuscular (I.M.) or subcutaneous (S.C.) routes. Comparison analysis of the fluorescence of soluble inulin in the supernatants of homogenised tissues maintained at room temperature or heated to 100°C to solubilise particulate inulin was used to distinguish between fluorescent probe on soluble inulin and probe bound to inulin within particles. Following both I.M. and S.C. injection delta inulin exhibited a depot behaviour with local injection site residence for several weeks. Over this time, as injection site inulin reduced, there was measurable transport of intact delta inulin particles by macrophages to secondary lymphoid organs and the liver. Ultimately, the injected delta inulin became solubilised resulting in its detection in the plasma and in the urine. Thus injected delta inulin particles are initially taken up by macrophages at the site of injection, trafficked to secondary lymphoid tissue and the liver, and hydrolysed resulting in their becoming soluble and diffusing into the blood stream, from whence they are glomerularly filtered and excreted into the urine. These results provide important insights into the biodistribution of I.M. or S.C. injected delta inulin particles when used as vaccine adjuvants and their method of excretion.
Publisher: Elsevier BV
Date: 03-2014
Publisher: Wiley
Date: 12-09-2017
Publisher: American Chemical Society (ACS)
Date: 29-06-2016
Abstract: Graphene oxide (GO) nanosheets have antibacterial properties that have been exploited as a biocidal agent used on desalination membrane surfaces in recent research. Nonetheless, improved strategies for efficient and stable attachment of GO nanosheets onto the membrane surface are still required for this idea to be commercially viable. To address this challenge, we adopted a novel, single-step surface modification approach using tannic acid cross-linked with polyethylene imine as a versatile platform to immobilize GO nanosheets to the surface of polyamide thin film composite forward osmosis (FO) membranes. An experimental design based on Taguchi's statistical method was applied to optimize the FO processing conditions in terms of water and reverse solute fluxes. Modified membranes were analyzed using water contact angle, adenosine triphosphate bioluminescence, total organic carbon, Fourier transform infrared spectroscopy, ζ potential, X-ray photoelectron spectroscopy, transmission electron microscopy, and atomic force microscopy. These results show that membranes were modified with a nanoscale (<10 nm), smooth, hydrophilic coating that, compared to pristine membranes, improved filtration and significantly mitigated biofouling by 33% due to its extraordinary, synergistic antibacterial properties (99.9%).
Publisher: Elsevier BV
Date: 05-2018
Publisher: Elsevier BV
Date: 08-2015
Publisher: Elsevier BV
Date: 05-2016
Publisher: Elsevier BV
Date: 2012
Publisher: MDPI AG
Date: 22-05-2019
DOI: 10.3390/PHARMACEUTICS11050243
Abstract: The propensity of monocytes to migrate into sites of mycobacterium tuberculosis (TB) infection and then become infected themselves makes them potential targets for delivery of drugs intracellularly to the tubercle bacilli reservoir. Conventional TB drugs are less effective because of poor intracellular delivery to this bacterial sanctuary. This study highlights the potential of using semicrystalline delta inulin particles that are readily internalised by monocytes for a monocyte-based drug delivery system. Pyrazinoic acid was successfully attached covalently to the delta inulin particles via a labile linker. The formation of new conjugate and amide bond was confirmed using zeta potential, Proton Nuclear Magnetic Resonance (1HNMR) and Fourier transform infrared spectroscopy (FTIR). Scanning electron microscopy (SEM) confirmed that no significant change in size after conjugation which is an important parameter for monocyte targeting. Thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) were used to establish the change in thermal properties. The analysis of in-vitro release demonstrated pH-triggered drug cleavage off the delta inulin particles that followed a first-order kinetic process. The efficient targeting ability of the conjugate for RAW 264.7 monocytic cells was supported by cellular uptake studies. Overall, our finding confirmed that semicrystalline delta inulin particles (MPI) can be modified covalently with drugs and such conjugates allow intracellular drug delivery and uptake into monocytes, making this system potentially useful for the treatment of TB.
Publisher: MDPI AG
Date: 22-07-2019
DOI: 10.3390/PHARMACEUTICS11070356
Abstract: Inulin-based hydrogels are useful carriers for the delivery of drugs in the colon-targeted system and in other biomedical applications. In this project, inulin hydrogels were fabricated by crosslinking oxidized inulin with adipic acid dihydrazide (AAD) without the use of a catalyst or initiator. The physicochemical properties of the obtained hydrogels were further characterized using different techniques, such as swelling experiments, in vitro drug release, degradation, and biocompatibility tests. The crosslinking was confirmed with Fourier transform infrared spectroscopy (FTIR), thermal gravimetric analysis (TGA), and differential scanning calorimetry (DSC). In vitro releases of 5-fluorouracil (5FU) from the various inulin hydrogels was enhanced in acidic conditions (pH 5) compared with physiological pH (pH 7.4). In addition, blank gels did not show any appreciable cytotoxicity, whereas 5FU-loaded hydrogels demonstrated efficacy against HCT116 colon cancer cells, which further confirms the potential use of these delivery platforms for direct targeting of 5-FU to the colon.
Publisher: Elsevier BV
Date: 06-2016
Publisher: Elsevier BV
Date: 03-2015
Publisher: Elsevier BV
Date: 05-2012
Publisher: MDPI AG
Date: 28-10-2019
DOI: 10.3390/PHARMACEUTICS11110555
Abstract: The use of particles for monocyte-mediated delivery could be a more efficient strategy and approach to achieve intracellular targeting and delivery of antitubercular drugs to host macrophages. In this study, the potential of inulin microparticles to serve as a drug vehicle in the treatment of chronic tuberculosis using a monocytes-mediated drug targeting approach was evaluated. Isoniazid (INH) was conjugated to inulin via hydrazone linkage in order to obtain a pH-sensitive inulin-INH conjugate. The conjugate was then characterized using proton nuclear magnetic resonance (1HNMR), Fourier transform infrared spectroscopy (FTIR) as well as in vitro, cellular uptake and intracellular Mycobacterium tuberculosis (Mtb) antibacterial efficacy. The acid-labile hydrazone linkage conferred pH sensitivity to the inulin-INH conjugate with ~95, 77 and 65% of the drug released after 5 h at pH 4.5, 5.2, and 6.0 respectively. Cellular uptake studies confirm that RAW 264.7 monocytic cells efficiently internalized the inulin conjugates into endocytic compartments through endocytosis. The intracellular efficacy studies demonstrate that the inulin conjugates possess a dose-dependent targeting effect against Mtb-infected monocytes. This was through efficient internalization and cleavage of the hydrazone bond by the acidic environment of the lysosome, which subsequently released the isoniazid intracellularly to the Mtb reservoir. These results clearly suggest that inulin conjugates can serve as a pH-sensitive intracellular drug delivery system for TB treatment.
Publisher: The Royal Society of Chemistry
Date: 09-07-2018
Abstract: The increased understanding of molecular aspects associated with chronic diseases, such as cancer and the role of tumor microenvironment, has led to the identification of endogenous and exogenous stimuli that can be exploited to devise “stimuli-responsive” materials for site-specific drug delivery applications. This book provides a comprehensive account on the design, materials chemistry, and application aspects behind these novel stimuli-responsive materials. Setting the scene, the editors open with a chapter addressing the need for smart materials in delivery applications for therapy, imaging and disease diagnosis. The following chapter describes the key physical and chemical aspects of smart materials, from lipids to polymers to hybrid materials, providing the reader with a springboard to delve into the more application oriented chapters that follow. With in-depth coverage of key drug delivery systems such as pH-responsive, temperature responsive, enzyme-responsive and light responsive systems, this book provides a rigorous foundation to the field. A perfect resource for graduate students and newcomers, the closing chapter on regulatory and commercialization challenges also makes the book ideal for those wanting to take the next step towards clinical translation.
Publisher: American Chemical Society (ACS)
Date: 06-08-2015
Abstract: Graphene oxide (GO) nanosheets were attached to the polyamide selective layer of thin film composite (TFC) forward osmosis (FO) membranes through a poly L-Lysine (PLL) intermediary using either layer-by-layer or hybrid (H) grafting strategies. Fourier transform infrared spectroscopy, zeta potential, and thermogravimetric analysis confirmed the successful attachment of GO/PLL, the surface modification enhancing both the hydrophilicity and smoothness of the membrane's surface demonstrated by water contact angle, atomic force microscopy, and transmission electron microscopy. The biofouling resistance of the FO membranes determined using an adenosine triphosphate bioluminescence test showed a 99% reduction in surviving bacteria for GO/PLL-H modified membranes compared to pristine membrane. This antibiofouling property of the GO/PLL-H modified membrane was reflected in reduced flux decline compared to all other s les when filtering brackish water under biofouling conditions. Further, the high density and tightly bound GO nanosheets using the hybrid modification reduced the reverse solute flux compared to the pristine, which reflects improved membrane selectivity. These results illustrate that the GO/PLL-H modification is a valuable addition to improve the performance of FO TFC membranes.
Publisher: Elsevier BV
Date: 10-2019
Start Date: 2015
End Date: 2018
Funder: Australian Research Council
View Funded Activity